Bao Zhang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Bao Zhang has a total of 6 co-authors. Here are the top co-authors by number of shared publications:
- Chunyu Zhao
School of Mechanical Engineering and Automation, Northeastern University, Shenyang 110819, China
2 shared publications - Jiaming Bian
School of Mechanical Engineering, Xi’an Jiaotong University, Xi’an 710049, China
1 shared publication - Jun Peng
School of Mechanical Engineering, Xi’an Jiaotong University, Xi’an 710049, China
1 shared publication - Shuhai Jia
Xi’an Jiaotong University
1 shared publication - Shunjian Xu
School of Intelligent Manufacturing, Huzhou College, Huzhou 313000, China
1 shared publication - Shuo Zhang
School of Mechanical Engineering, Xi’an Jiaotong University, Xi’an 710049, China
1 shared publication
Latest Publications
- 19 September 2023
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science
- Vol. 238 (7) , 2758-2771
Steady state prediction model and spectrum characteristics analysis of cutting force for CNC lathe considering variable machining parameters
This paper presents a steady state cutting force prediction model for CNC lathe considering feed displacement. The frequency spectrum characteristics of the cutting force in principal direction are analyzed. The turning test for 12Cr18Ni9 stainless steel workpiece is carried out by CNC machine tool ETC1625P firstly, and the real-time displacement data of worktable in the turning process are obtained. The cutting force data varying with the displacement of the worktable under different cutting parameters are obtained by cubic spline interpolation. The mechanical force model including metal shearing force and plowing force is established, so as to predict the steady state cutting force accurately corresponding to different displacement of the worktable. The influence of different cutting parameters on the amplitude frequency characteristics for the low frequency part of the cutting force in principal direction is studied by using wavelet packet decomposition and fast Fourier transform. The results show that the method can predict the steady cutting force accurately and reflect the amplitude frequency characteristics of the low frequency part for the cutting force in principal direction under different cutting parameters.
- 19 September 2023
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science
- Vol. 238 (7) , 2758-2771
Steady state prediction model and spectrum characteristics analysis of cutting force for CNC lathe considering variable machining parameters
This paper presents a steady state cutting force prediction model for CNC lathe considering feed displacement. The frequency spectrum characteristics of the cutting force in principal direction are analyzed. The turning test for 12Cr18Ni9 stainless steel workpiece is carried out by CNC machine tool ETC1625P firstly, and the real-time displacement data of worktable in the turning process are obtained. The cutting force data varying with the displacement of the worktable under different cutting parameters are obtained by cubic spline interpolation. The mechanical force model including metal shearing force and plowing force is established, so as to predict the steady state cutting force accurately corresponding to different displacement of the worktable. The influence of different cutting parameters on the amplitude frequency characteristics for the low frequency part of the cutting force in principal direction is studied by using wavelet packet decomposition and fast Fourier transform. The results show that the method can predict the steady cutting force accurately and reflect the amplitude frequency characteristics of the low frequency part for the cutting force in principal direction under different cutting parameters.
- Open Access
- 22 February 2021
- Published by MDPI AG in Micromachines
- Vol. 12 (2) , 221
Design and Fabrication of a MEMS Electromagnetic Swing-Type Actuator for Optical Switch
A microelectromechanical systems system (MEMS) electromagnetic swing-type actuator is proposed for an optical fiber switch in this paper. The actuator has a compact size of 5.1 × 5.1 × 5.3 mm3, consisting of two stators, a swing disc (rotator), a rotating shaft, and protective covers. Multi-winding stators and a multipole rotator were adopted to increase the output torque of the actuator. The actuator’s working principle and magnetic circuit were analyzed. The calculation results show that the actuator’s output torque is decisive to the air gap’s magnetic flux density between the stators and the swing disc. NiFe alloy magnetic cores were embedded into each winding center to increase the magnetic flux density. A special manufacturing process was developed for fabricating the stator windings on the ferrite substrate. Six copper windings and NiFe magnetic cores were electroplated onto the ferrite substrates. The corresponding six magnetic poles were configured to the SmCo permanent magnet on the swing disc. A magnetizing device with a particular size was designed and fabricated to magnetize the permanent magnet of the swing disc. The actuator prototype was fabricated, and the performance was tested. The results show that the actuator has a large output torque (40 μNm), fast response (5 ms), and a large swing angle (22°).
- 22 February 2021
- Published by MDPI AG in Micromachines
- Vol. 12 (2) , 221
Open AccessDesign and Fabrication of a MEMS Electromagnetic Swing-Type Actuator for Optical Switch
A microelectromechanical systems system (MEMS) electromagnetic swing-type actuator is proposed for an optical fiber switch in this paper. The actuator has a compact size of 5.1 × 5.1 × 5.3 mm3, consisting of two stators, a swing disc (rotator), a rotating shaft, and protective covers. Multi-winding stators and a multipole rotator were adopted to increase the output torque of the actuator. The actuator’s working principle and magnetic circuit were analyzed. The calculation results show that the actuator’s output torque is decisive to the air gap’s magnetic flux density between the stators and the swing disc. NiFe alloy magnetic cores were embedded into each winding center to increase the magnetic flux density. A special manufacturing process was developed for fabricating the stator windings on the ferrite substrate. Six copper windings and NiFe magnetic cores were electroplated onto the ferrite substrates. The corresponding six magnetic poles were configured to the SmCo permanent magnet on the swing disc. A magnetizing device with a particular size was designed and fabricated to magnetize the permanent magnet of the swing disc. The actuator prototype was fabricated, and the performance was tested. The results show that the actuator has a large output torque (40 μNm), fast response (5 ms), and a large swing angle (22°).
- 20 November 2019
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science
- Vol. 234 (5) , 1044-1056
Dynamic turning force prediction and feature parameters extraction of machine tool based on ARMA and HHT
The dynamic prediction of turning force is an effective means to reflect the changing course and characteristics of the force in the whole cutting process. It is very important to model and predict the turning force and analyze its spectrum characteristics. In order to obtain the dynamic turning force, the circular cutting experiment of 12Cr18Ni9 rotary piece was carried out on the numerical control machine ETC1625P. The KISTLER sensor was mounted on the tool head of the machine tool, and the real-time turning forces in three cutting directions were measured. The experimental data show that the turning force fluctuates with the change of displacement in the feed direction. In order to study the complex nonlinear relationship between turning force and cutting parameters, the dynamic turning force was predicted by autoregressive-moving average modeling. The time–frequency analysis of the main turning force was carried out by using Hilbert–Huang transform. The local time–frequency characteristics of the signal were obtained by analyzing the Hilbert amplitude spectrum of the signal. When only one cutting parameter was changed, the maximum amplitude of Hilbert marginal spectrum of turning force signal changed with the change of cutting parameters. The results show that the high-precision modeling of dynamic turning force and the extraction of cutting features can be effectively realized by using autoregressive-moving average and Hilbert–Huang transform.
- 20 November 2019
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science
- Vol. 234 (5) , 1044-1056
Dynamic turning force prediction and feature parameters extraction of machine tool based on ARMA and HHT
The dynamic prediction of turning force is an effective means to reflect the changing course and characteristics of the force in the whole cutting process. It is very important to model and predict the turning force and analyze its spectrum characteristics. In order to obtain the dynamic turning force, the circular cutting experiment of 12Cr18Ni9 rotary piece was carried out on the numerical control machine ETC1625P. The KISTLER sensor was mounted on the tool head of the machine tool, and the real-time turning forces in three cutting directions were measured. The experimental data show that the turning force fluctuates with the change of displacement in the feed direction. In order to study the complex nonlinear relationship between turning force and cutting parameters, the dynamic turning force was predicted by autoregressive-moving average modeling. The time–frequency analysis of the main turning force was carried out by using Hilbert–Huang transform. The local time–frequency characteristics of the signal were obtained by analyzing the Hilbert amplitude spectrum of the signal. When only one cutting parameter was changed, the maximum amplitude of Hilbert marginal spectrum of turning force signal changed with the change of cutting parameters. The results show that the high-precision modeling of dynamic turning force and the extraction of cutting features can be effectively realized by using autoregressive-moving average and Hilbert–Huang transform.