Alexey Stepanov
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Alexey Stepanov has a total of 22 co-authors. Here are the top co-authors by number of shared publications:
- Anton V. Koldaev
Bardin Central Research Institute of Ferrous Metallurgy, Moscow, Russian Federation
11 shared publications - Alexander I. Zaitsev
Bardin Central Research Institute of Ferrous Metallurgy, Moscow 105005, Russia
7 shared publications - Aleksey I. Dagman
NLMK PJSC, Lipetsk, Russian Federation
6 shared publications - D. A. Kovalev
Novolipetsk Steel PJSC, Lipetsk, Russia
4 shared publications - Nataliya Arutyunyan
I.P. Bardin Central Research Institute of Ferrous Metallurgy; M.V. Lomonosov Moscow State University
4 shared publications A. I. Zaitsev
Bardin Central Research Institute of Ferrous Metallurgy (TsNIIchermet)
3 shared publications
Latest Publications
- 21 July 2023
- Published by Springer Nature in Metallurgist
- Vol. 67 (3-4) , 265-272
Justification of the Production Technology Efficiency for High-Strength, Low-Alloy Steels with Improved Properties and Quality at Low-Cost. Part 2. Cold-Rolled Products
- 21 July 2023
- Published by Springer Nature in Metallurgist
- Vol. 67 (3-4) , 265-272
Justification of the Production Technology Efficiency for High-Strength, Low-Alloy Steels with Improved Properties and Quality at Low-Cost. Part 2. Cold-Rolled Products
- 29 May 2023
- Published by Springer Nature in Metallurgist
- Vol. 67 (1-2) , 1-12
Justification of the Production Technology Efficiency for Low-Alloy Steels with Improved Properties and Quality at Low-Cost. Part 1. Hot-Rolled Products
- 29 May 2023
- Published by Springer Nature in Metallurgist
- Vol. 67 (1-2) , 1-12
Justification of the Production Technology Efficiency for Low-Alloy Steels with Improved Properties and Quality at Low-Cost. Part 1. Hot-Rolled Products
- 1 March 2023
- Published by Springer Nature in Metallurgist
- Vol. 66 (11-12) , 1497-1511
Investigation of Production Technology for Hot-Rolled High-Strength Low-Alloy Automobile Sheet Steels to Improve Properties and Quality Indices at Reduced Cost
- 1 March 2023
- Published by Springer Nature in Metallurgist
- Vol. 66 (11-12) , 1497-1511
Investigation of Production Technology for Hot-Rolled High-Strength Low-Alloy Automobile Sheet Steels to Improve Properties and Quality Indices at Reduced Cost
- Open Access
Study of the Effect of Quenching and Tempering Modes on the Strength Level of Alloyed Structural Steels Used to Produce Fasteners
The development of high-strength fasteners is required due to the modern trend of reducing the weight of engineering structures. At present, structural bolts of property classes 8.8–10.9 are widely used, and higher-strength bolts of property classes 12.9 and 14.9 are being developed. In this paper, we analyzed the possibilities and conditions for manufacturing fasteners of different strength categories from steels of seven grades, containing and not containing boron. The necessary corresponding temperature ranges of processing are determined based on the study of hot-rolled round steel. Tensile strength, yield strength, relative elongation, reduction in area, and Vickers microhardness were measured. An analysis was made of the hardenability and the influence of the holding time during tempering on the mechanical properties of the considered round steel. Using the method of scanning electron microscopy, the effect of carbide precipitation during tempering on the mechanical properties of fasteners was established.
Open AccessStudy of the Effect of Quenching and Tempering Modes on the Strength Level of Alloyed Structural Steels Used to Produce Fasteners
The development of high-strength fasteners is required due to the modern trend of reducing the weight of engineering structures. At present, structural bolts of property classes 8.8–10.9 are widely used, and higher-strength bolts of property classes 12.9 and 14.9 are being developed. In this paper, we analyzed the possibilities and conditions for manufacturing fasteners of different strength categories from steels of seven grades, containing and not containing boron. The necessary corresponding temperature ranges of processing are determined based on the study of hot-rolled round steel. Tensile strength, yield strength, relative elongation, reduction in area, and Vickers microhardness were measured. An analysis was made of the hardenability and the influence of the holding time during tempering on the mechanical properties of the considered round steel. Using the method of scanning electron microscopy, the effect of carbide precipitation during tempering on the mechanical properties of fasteners was established.
- 1 July 2022
- Published by Springer Nature in Metallurgist
- Vol. 66 (3-4) , 359-367
Creation of an Effective Technology for the Production of Cold-Rolled High-Strength Low-Alloy Steels with High and Stable Properties. Part 2. Cold-rolled Products
- 1 July 2022
- Published by Springer Nature in Metallurgist
- Vol. 66 (3-4) , 359-367
Creation of an Effective Technology for the Production of Cold-Rolled High-Strength Low-Alloy Steels with High and Stable Properties. Part 2. Cold-rolled Products
- 1 July 2022
- Published by Springer Nature in Metallurgist
- Vol. 66 (3-4) , 243-254
Creation of an Effective Technology for the Production of Cold-Rolled High-Strength Low-Alloy Steels with High and Stable Properties. Part 1. Hot-rolled Products
- 1 July 2022
- Published by Springer Nature in Metallurgist
- Vol. 66 (3-4) , 243-254
Creation of an Effective Technology for the Production of Cold-Rolled High-Strength Low-Alloy Steels with High and Stable Properties. Part 1. Hot-rolled Products
- Open Access
Evolution of the Structural State and Properties of 32CrB4 Steel during the Production of High-Strength Fasteners
For the production of high-strength fasteners, bar sections are used, which must withstand significant cold plastic deformation and, therefore, are subjected to a special heat treatment. In the present work, the dependences of the microstructure and mechanical properties of round bars with diameters of 17 mm and 21 mm made of 32CrB4 steel on the heat treatment modes are established. During the study, the methods of optical and scanning electron microscopy, mechanical tests, and hardness measurements were used. Dependences of the degree of spheroidization of the ferrite–pearlite structure and mechanical properties on the spheroidizing annealing mode have been established. It is shown that preliminary obtainment of a bainitic or martensitic structure of rolled products after hot-rolling of steel accelerates the process of pearlite spheroidization. Additional heat treatment, including austenitizing, quenching, and tempering, allows obtaining fasteners of various strength classes: 8.8, 9.8, and 10.9. However, with a guaranteed receipt of strength characteristics for all strength classes, including 12.9, the problem arises of achieving the required values of the relative elongation of steel.
Open AccessEvolution of the Structural State and Properties of 32CrB4 Steel during the Production of High-Strength Fasteners
For the production of high-strength fasteners, bar sections are used, which must withstand significant cold plastic deformation and, therefore, are subjected to a special heat treatment. In the present work, the dependences of the microstructure and mechanical properties of round bars with diameters of 17 mm and 21 mm made of 32CrB4 steel on the heat treatment modes are established. During the study, the methods of optical and scanning electron microscopy, mechanical tests, and hardness measurements were used. Dependences of the degree of spheroidization of the ferrite–pearlite structure and mechanical properties on the spheroidizing annealing mode have been established. It is shown that preliminary obtainment of a bainitic or martensitic structure of rolled products after hot-rolling of steel accelerates the process of pearlite spheroidization. Additional heat treatment, including austenitizing, quenching, and tempering, allows obtaining fasteners of various strength classes: 8.8, 9.8, and 10.9. However, with a guaranteed receipt of strength characteristics for all strength classes, including 12.9, the problem arises of achieving the required values of the relative elongation of steel.