Haifeng Zou
Research Subjects
Haifeng Zou has a total of 15 co-authors. Here are the top co-authors by number of shared publications:
- Anand Jagadeesh Puppala
Zachry Department of Civil and Environmental Engineering, Texas A&M University, College Station, TX
5 shared publications - Guojun Cai
Institute of Geotechnical Engineering, School of Transportation, Southeast University, Nanjing, China
4 shared publications - Songyu Liu
Institute of Geotechnical Engineering, Southeast University, Nanjing, China
4 shared publications - Tejo Vikash Bheemasetti
The University of Texas at Arlington
3 shared publications - Aravind Pedarla
Postdoctoral Fellow, Dept. of Civil Engineering, Univ. of Texas at Arlington, Arlington, TX 76019
1 shared publication - Bhaskar Chittoori
Boise State University
1 shared publication
Latest Publications
- 1 February 2017
- Published by American Society of Civil Engineers (ASCE) in Journal of Geotechnical and Geoenvironmental Engineering
- Vol. 143 (2)
Spatial Mapping of Soluble Sulfate Concentrations Present in Natural Soils Using Geostatistics
Sulfate heaving has had a major impact on civil engineering infrastructure for the past few decades. Past researchers have attributed the provenance of this heaving mechanism to the chemical reactions between soluble sulfates and calcium-based stabilizers, but despite the increase in studies related to sulfate heaving, very little effort has been made to address the variability of sulfate concentrations in the field. The natural deposition of sulfate pockets causes inevitable problems to chemical stabilization techniques. Because of the high variability of sulfate concentrations present in nearby locations, it is possible that engineers may mischaracterize the sulfate concentrations or not able to design appropriate stabilization measures in the field. In this study geostatistical analysis was used to quantify and map sulfate concentrations along a mega water pipeline project located in north Texas. Various soil samples, originating from six different geological formations along the pipeline alignment, were collected. Laboratory tests were performed on these soil samples to determine soluble sulfate concentrations using the modified University of Texas at Arlington (UTA) approach. The inherent variability present in sulfate concentrations was determined and modeled using variogram analysis. The variability models, along with the kriging algorithm, were used to determine the distribution of the sulfate concentrations at unsampled locations along the pipeline alignment. This analysis provided the distribution of soluble sulfate concentrations along the six geological formations and indicated the areas of having low-risk to high risk zones when treated with calcium-based stabilizers. This research highlights the adoptability of geostatistics in modeling and mapping the high variable soluble sulfate concentrations present in native clayey soils.
- 1 February 2017
- Published by American Society of Civil Engineers (ASCE) in Journal of Geotechnical and Geoenvironmental Engineering
- Vol. 143 (2)
Spatial Mapping of Soluble Sulfate Concentrations Present in Natural Soils Using Geostatistics
Sulfate heaving has had a major impact on civil engineering infrastructure for the past few decades. Past researchers have attributed the provenance of this heaving mechanism to the chemical reactions between soluble sulfates and calcium-based stabilizers, but despite the increase in studies related to sulfate heaving, very little effort has been made to address the variability of sulfate concentrations in the field. The natural deposition of sulfate pockets causes inevitable problems to chemical stabilization techniques. Because of the high variability of sulfate concentrations present in nearby locations, it is possible that engineers may mischaracterize the sulfate concentrations or not able to design appropriate stabilization measures in the field. In this study geostatistical analysis was used to quantify and map sulfate concentrations along a mega water pipeline project located in north Texas. Various soil samples, originating from six different geological formations along the pipeline alignment, were collected. Laboratory tests were performed on these soil samples to determine soluble sulfate concentrations using the modified University of Texas at Arlington (UTA) approach. The inherent variability present in sulfate concentrations was determined and modeled using variogram analysis. The variability models, along with the kriging algorithm, were used to determine the distribution of the sulfate concentrations at unsampled locations along the pipeline alignment. This analysis provided the distribution of soluble sulfate concentrations along the six geological formations and indicated the areas of having low-risk to high risk zones when treated with calcium-based stabilizers. This research highlights the adoptability of geostatistics in modeling and mapping the high variable soluble sulfate concentrations present in native clayey soils.
- 8 August 2016
- Published by American Society of Civil Engineers (ASCE)
- p. 527-538
Geostatistical Modeling Resistivity of Cohesionless Soil Using RCPTU Data
Resistivity of soils has been widely used for analyzing both geotechnical and geoenvironmental problems. Mapping the distribution of resistivity provides significant information for site characterization including soil properties and contamination in the subsoil. In this research, the distribution of resistivity of a silty sand is investigated using resistivity piezocone penetration test (RCPTU) based on geostatistics. First, to achieve stationary Gaussian random field, the trend removal and Box-Cox transformation were used to convert non-stationary and non-Gaussian resistivity measurements into weakly stationary normal random field. Then semivariogram was used to describe the spatial variability of the residuals including variance, correlation length and nugget. The maximum likelihood (ML) estimator was applied to estimate the theoretical semivariogram, revealing that anisotropy exists in the spatial correlation structure. Ordinary Kriging was then used to provide the best linear unbiased estimates of residuals at unsampled locations of the random field. Finally, cross-validation, or removing some known observations from the database and predicting the known results, was used to validate the geostatistics model. It was shown that the geostatistics is a powerful tool to map the resistivity of subsoil by considering the spatial variability characteristics.
- 8 August 2016
- Published by American Society of Civil Engineers (ASCE)
- p. 527-538
Geostatistical Modeling Resistivity of Cohesionless Soil Using RCPTU Data
Resistivity of soils has been widely used for analyzing both geotechnical and geoenvironmental problems. Mapping the distribution of resistivity provides significant information for site characterization including soil properties and contamination in the subsoil. In this research, the distribution of resistivity of a silty sand is investigated using resistivity piezocone penetration test (RCPTU) based on geostatistics. First, to achieve stationary Gaussian random field, the trend removal and Box-Cox transformation were used to convert non-stationary and non-Gaussian resistivity measurements into weakly stationary normal random field. Then semivariogram was used to describe the spatial variability of the residuals including variance, correlation length and nugget. The maximum likelihood (ML) estimator was applied to estimate the theoretical semivariogram, revealing that anisotropy exists in the spatial correlation structure. Ordinary Kriging was then used to provide the best linear unbiased estimates of residuals at unsampled locations of the random field. Finally, cross-validation, or removing some known observations from the database and predicting the known results, was used to validate the geostatistics model. It was shown that the geostatistics is a powerful tool to map the resistivity of subsoil by considering the spatial variability characteristics.
- 1 April 2016
- Published by American Society of Civil Engineers (ASCE) in Journal of Materials in Civil Engineering
- Vol. 28 (4)
Quality Assurance Method for Assessment of Stiffness of Pipeline Bedding Material
An innovative quality assurance method is used to assess the stiffness of the bedding material to a water pipeline located in Texas. The method used is a combination of spectral analysis of surface waves technique (SASW) and geostatistics. SASW tests were conducted to measure the stiffness of pipeline bedding material at 15 sections along the pipeline after different curing periods of 1, 3, 7, 14, and 28 days. The stiffness measurements from SASW tests are used in geostatistical analysis to determine stiffness properties at untested locations and map the variation of stiffness values along the pipeline. The SASW measurements indicated a significant increase in mean stiffness value of bedding material from 267.5 MPa on day 1 to 442 MPa after a 28-day curing period. The geostatistical analysis predicted and mapped the stiffness of bedding material over the entire pipeline by incorporating the variability present in the known stiffness measurements. This research highlights the adaptability of geostatistics and in situ measurements in assessing the quality of the pipeline bedding material.
- 1 April 2016
- Published by American Society of Civil Engineers (ASCE) in Journal of Materials in Civil Engineering
- Vol. 28 (4)
Quality Assurance Method for Assessment of Stiffness of Pipeline Bedding Material
An innovative quality assurance method is used to assess the stiffness of the bedding material to a water pipeline located in Texas. The method used is a combination of spectral analysis of surface waves technique (SASW) and geostatistics. SASW tests were conducted to measure the stiffness of pipeline bedding material at 15 sections along the pipeline after different curing periods of 1, 3, 7, 14, and 28 days. The stiffness measurements from SASW tests are used in geostatistical analysis to determine stiffness properties at untested locations and map the variation of stiffness values along the pipeline. The SASW measurements indicated a significant increase in mean stiffness value of bedding material from 267.5 MPa on day 1 to 442 MPa after a 28-day curing period. The geostatistical analysis predicted and mapped the stiffness of bedding material over the entire pipeline by incorporating the variability present in the known stiffness measurements. This research highlights the adaptability of geostatistics and in situ measurements in assessing the quality of the pipeline bedding material.
- 4 February 2016
- Published by Springer Nature in Bulletin of Engineering Geology and the Environment
- Vol. 76 (1) , 353-369
Random field characterization of CPTU soil behavior type index of Jiangsu quaternary soil deposits
- 4 February 2016
- Published by Springer Nature in Bulletin of Engineering Geology and the Environment
- Vol. 76 (1) , 353-369
Random field characterization of CPTU soil behavior type index of Jiangsu quaternary soil deposits
- 5 May 2014
- Published by American Society of Civil Engineers (ASCE)
- p. 845-854
Application of the Piezocone Penetration Testing to Assess Flow Characteristics of Marine Clay
Parameters from piezocone test (CPTU) are commonly used for soil profiling and geostratigraphy, along with the parameters used for assessment of geotechnical design. CPTU provides near-continuous measurements of tip resistance, sleeve friction and pore pressure at the shoulder, or face, or shaft of the cone. The dissipation results in CPTU soundings are used to evaluate the coefficient of consolidation and permeability of soil at intermittent depth. Recently, however, several approaches based on CPTU data to assessing the hydraulic conductivity of soils continuously are developed to avoid the time-consuming dissipation of excess pore pressure. This paper presents an experiment, centered on the use of piezocone tests, to determine the flow characteristics of cohesive soils on the engineering background of design of a transformer substation in Lianyungang, China. Three methods (two continuous and one discontinuous) are applied to obtain the coefficient of permeability of soils, and the results are compared with those from laboratory tests. This study confirmed the potential for use of piezocone tests to obtain valid predictions for flow characteristics of soils.
- 5 May 2014
- Published by American Society of Civil Engineers (ASCE)
- p. 845-854
Application of the Piezocone Penetration Testing to Assess Flow Characteristics of Marine Clay
Parameters from piezocone test (CPTU) are commonly used for soil profiling and geostratigraphy, along with the parameters used for assessment of geotechnical design. CPTU provides near-continuous measurements of tip resistance, sleeve friction and pore pressure at the shoulder, or face, or shaft of the cone. The dissipation results in CPTU soundings are used to evaluate the coefficient of consolidation and permeability of soil at intermittent depth. Recently, however, several approaches based on CPTU data to assessing the hydraulic conductivity of soils continuously are developed to avoid the time-consuming dissipation of excess pore pressure. This paper presents an experiment, centered on the use of piezocone tests, to determine the flow characteristics of cohesive soils on the engineering background of design of a transformer substation in Lianyungang, China. Three methods (two continuous and one discontinuous) are applied to obtain the coefficient of permeability of soils, and the results are compared with those from laboratory tests. This study confirmed the potential for use of piezocone tests to obtain valid predictions for flow characteristics of soils.