Daguo Wang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Daguo Wang has a total of 27 co-authors. Here are the top co-authors by number of shared publications:
- Qingxiang Shui
School of Energy Power Engineering, Xihua University, Chengdu 630019, China
3 shared publications Bin Li
School of Environmental and Resources, Southwest University of Science and Technology, Mianyang, China
1 shared publicationBing Xu
School of Environmental and Resources, Southwest University of Science and Technology, Mianyang, China
1 shared publication- Bing Xu
School of Environment and Resource, Southwest University of Science and Technology, Mianyang 621010, China
1 shared publication Chaochao Han
School of Environmental and Resources, Southwest University of Science and Technology, Mianyang, China
1 shared publicationChunAn Tang
Dalian University of Technology
1 shared publication
Latest Publications
- Open Access
- 6 October 2023
- Published by MDPI AG in Sustainability
- Vol. 15 (19) , 14524
Study on Temperature Distribution Law of Tunnel Portal Section in Cold Region Considering Fluid–Structure Interaction
The design of tunnels in cold regions contributes greatly to the feasibility and sustainability of highways. Based on the heat transfer mechanism of the tunnel surrounding rock–lining–air, this paper uses FEPG software to carry out secondary excavation and development, then the air heat convection calculation model is established by using a three-dimensional extension of the characteristic-based operator-splitting (CBOS) finite-element method and the explicit characteristic–Galerkin method. By coupling with the heat conduction model of the tunnel lining and surrounding rock, the heat conduction-thermal convection fluid–structure interaction finite-element calculation model of tunnels in cold regions is established. Relying on the Qinghai Hekashan tunnel project, the temperature field of the tunnel portal section is calculated and studied by employing the fluid–structure interaction finite-element model and then compared with the field monitoring results. It is found that the calculated values are basically consistent with the measured values over time, which proves the reliability of the model. The calculation results are threefold: (1) The temperature of the air, lining, and surrounding rock in the tunnel changes sinusoidally with the ambient temperature. (2) The temperature of each layer gradually lags behind, and the temperature variation amplitude of the extreme value of the layer temperature gradually decreases with the increase in the radial distance of the lining. (3) In the vicinity of the tunnel entrance, the lining temperature of each layer remains unchanged, and the temperature gradually decreases or increases with the increase in the depth. The model can be used to study and analyze the temperature field distribution law of the lining and surrounding rock under different boundary conditions, and then provide a calculation model with both research and practical value for the study of the temperature distribution law of tunnels in cold regions in the future.
- 6 October 2023
- Published by MDPI AG in Sustainability
- Vol. 15 (19) , 14524
Open AccessStudy on Temperature Distribution Law of Tunnel Portal Section in Cold Region Considering Fluid–Structure Interaction
The design of tunnels in cold regions contributes greatly to the feasibility and sustainability of highways. Based on the heat transfer mechanism of the tunnel surrounding rock–lining–air, this paper uses FEPG software to carry out secondary excavation and development, then the air heat convection calculation model is established by using a three-dimensional extension of the characteristic-based operator-splitting (CBOS) finite-element method and the explicit characteristic–Galerkin method. By coupling with the heat conduction model of the tunnel lining and surrounding rock, the heat conduction-thermal convection fluid–structure interaction finite-element calculation model of tunnels in cold regions is established. Relying on the Qinghai Hekashan tunnel project, the temperature field of the tunnel portal section is calculated and studied by employing the fluid–structure interaction finite-element model and then compared with the field monitoring results. It is found that the calculated values are basically consistent with the measured values over time, which proves the reliability of the model. The calculation results are threefold: (1) The temperature of the air, lining, and surrounding rock in the tunnel changes sinusoidally with the ambient temperature. (2) The temperature of each layer gradually lags behind, and the temperature variation amplitude of the extreme value of the layer temperature gradually decreases with the increase in the radial distance of the lining. (3) In the vicinity of the tunnel entrance, the lining temperature of each layer remains unchanged, and the temperature gradually decreases or increases with the increase in the depth. The model can be used to study and analyze the temperature field distribution law of the lining and surrounding rock under different boundary conditions, and then provide a calculation model with both research and practical value for the study of the temperature distribution law of tunnels in cold regions in the future.
- Open Access
- 15 March 2023
- Published by MDPI AG in Sustainability
- Vol. 15 (6) , 5201
Study on the Prediction of the Uniaxial Compressive Strength of Rock Based on the SSA-XGBoost Model
The uniaxial compressive strength of rock is one of the important parameters characterizing the properties of rock masses in geotechnical engineering. To quickly and accurately predict the uniaxial compressive strength of rock, a new SSA-XGBoost optimizer prediction model was produced to predict the uniaxial compressive strength of 290 rock samples. With four parameters, namely, porosity (n,%), Schmidt rebound number (Rn), longitudinal wave velocity (Vp, m/s), and point load strength (Is(50), MPa) as input variables and uniaxial compressive strength (UCS, MPa) as the output variables, a prediction model of uniaxial compressive strength was built based on the SSA-XGBoost model. To verify the effectiveness of the SSA-XGBoost model, empirical formulas, XGBoost, SVM, RF, BPNN, KNN, PLSR, and other models were also established and compared with the SSA-XGBoost model. All models were evaluated using the root mean square error (RMSE), correlation coefficient (R2), mean absolute error (MAE), and variance interpretation (VAF). The results calculated by the SSA-XGBoost model (R2 = 0.84, RMSE = 19.85, MAE = 14.79, and VAF = 81.36), are the best among all prediction models. Therefore, the SSA-XGBoost model is the best model to predict the uniaxial compressive strength of rock, for the dataset tested.
- 15 March 2023
- Published by MDPI AG in Sustainability
- Vol. 15 (6) , 5201
Open AccessStudy on the Prediction of the Uniaxial Compressive Strength of Rock Based on the SSA-XGBoost Model
The uniaxial compressive strength of rock is one of the important parameters characterizing the properties of rock masses in geotechnical engineering. To quickly and accurately predict the uniaxial compressive strength of rock, a new SSA-XGBoost optimizer prediction model was produced to predict the uniaxial compressive strength of 290 rock samples. With four parameters, namely, porosity (n,%), Schmidt rebound number (Rn), longitudinal wave velocity (Vp, m/s), and point load strength (Is(50), MPa) as input variables and uniaxial compressive strength (UCS, MPa) as the output variables, a prediction model of uniaxial compressive strength was built based on the SSA-XGBoost model. To verify the effectiveness of the SSA-XGBoost model, empirical formulas, XGBoost, SVM, RF, BPNN, KNN, PLSR, and other models were also established and compared with the SSA-XGBoost model. All models were evaluated using the root mean square error (RMSE), correlation coefficient (R2), mean absolute error (MAE), and variance interpretation (VAF). The results calculated by the SSA-XGBoost model (R2 = 0.84, RMSE = 19.85, MAE = 14.79, and VAF = 81.36), are the best among all prediction models. Therefore, the SSA-XGBoost model is the best model to predict the uniaxial compressive strength of rock, for the dataset tested.
- Open Access
- 13 August 2018
- Published by Springer Nature in China Ocean Engineering
- Vol. 32 (4) , 490-500
Least Square Finite Element Method for Viscous Splitting of Unsteady Incompressible Navier–Stokes Equations
- 13 August 2018
- Published by Springer Nature in China Ocean Engineering
- Vol. 32 (4) , 490-500
Open AccessLeast Square Finite Element Method for Viscous Splitting of Unsteady Incompressible Navier–Stokes Equations
- Open Access
- 1 January 2018
- Published by SAGE Publications in Journal of Applied Biomaterials & Functional Materials
- Vol. 16 (1_suppl) , 46-54
Numerical study on rupture process of fiber-reinforced composites
Introduction: This study aims to investigate the strength characteristics of fiber composites under uniaxial tensile stress. Methods: A tensile failure finite element model based on fracture mechanics was built for fiber composites. The principal stress concentration–release–transfer evolution and the crack propagation of the composites under the conditions of equal single fiber width, unequal quantity, and equal total fiber width and unequal quantity were discussed. Results: The tensile strength of the composites increased with fiber quantity when the width of each single fiber was equal. Conclusions: The tensile strength of the composites increased with fiber quantity when the total width of the composite fiber was equal.
- 1 January 2018
- Published by SAGE Publications in Journal of Applied Biomaterials & Functional Materials
- Vol. 16 (1_suppl) , 46-54
Open AccessNumerical study on rupture process of fiber-reinforced composites
Introduction: This study aims to investigate the strength characteristics of fiber composites under uniaxial tensile stress. Methods: A tensile failure finite element model based on fracture mechanics was built for fiber composites. The principal stress concentration–release–transfer evolution and the crack propagation of the composites under the conditions of equal single fiber width, unequal quantity, and equal total fiber width and unequal quantity were discussed. Results: The tensile strength of the composites increased with fiber quantity when the width of each single fiber was equal. Conclusions: The tensile strength of the composites increased with fiber quantity when the total width of the composite fiber was equal.
- Open Access
- 1 October 2017
- Published by AIP Publishing in AIP Advances
- Vol. 7 (10)
Numerical model of thermo-mechanical coupling for the tensile failure process of brittle materials
A numerical model of thermal cracking with a thermo-mechanical coupling effect was established. The theory of tensile failure and heat conduction is used to study the tensile failure process of brittle materials, such as rock and concrete under high temperature environment. The validity of the model is verified by thick-wall cylinders with analytical solutions. The failure modes of brittle materials under thermal stresses caused by temperature gradient and different thermal expansion coefficient were studied by using a thick-wall cylinder model and an embedded particle model, respectively. In the thick-wall cylinder model, different forms of cracks induced by temperature gradient were obtained under different temperature boundary conditions. In the embedded particle model, radial cracks were produced in the medium part with lower tensile strength when temperature increased because of the different thermal expansion coefficient. Model results are in good agreement with the experimental results, thereby providing a new finite element method for analyzing the thermal damage process and mechanism of brittle materials.
- 1 October 2017
- Published by AIP Publishing in AIP Advances
- Vol. 7 (10)
Open AccessNumerical model of thermo-mechanical coupling for the tensile failure process of brittle materials
A numerical model of thermal cracking with a thermo-mechanical coupling effect was established. The theory of tensile failure and heat conduction is used to study the tensile failure process of brittle materials, such as rock and concrete under high temperature environment. The validity of the model is verified by thick-wall cylinders with analytical solutions. The failure modes of brittle materials under thermal stresses caused by temperature gradient and different thermal expansion coefficient were studied by using a thick-wall cylinder model and an embedded particle model, respectively. In the thick-wall cylinder model, different forms of cracks induced by temperature gradient were obtained under different temperature boundary conditions. In the embedded particle model, radial cracks were produced in the medium part with lower tensile strength when temperature increased because of the different thermal expansion coefficient. Model results are in good agreement with the experimental results, thereby providing a new finite element method for analyzing the thermal damage process and mechanism of brittle materials.
- 16 September 2015
- Published by Springer Nature in Acta Mechanica Sinica
- Vol. 32 (1) , 54-63
SUPG finite element method based on penalty function for lid-driven cavity flow up to $Re = 27500$ R e = 27500- 16 September 2015
- Published by Springer Nature in Acta Mechanica Sinica
- Vol. 32 (1) , 54-63
SUPG finite element method based on penalty function for lid-driven cavity flow up to $Re = 27500$ R e = 27500- 27 August 2011
- Published by Springer Nature in China Ocean Engineering
- Vol. 25 (3) , 441-456
A 3-D time-domain coupled model for nonlinear waves acting on a box-shaped ship fixed in a harbor
- 27 August 2011
- Published by Springer Nature in China Ocean Engineering
- Vol. 25 (3) , 441-456
A 3-D time-domain coupled model for nonlinear waves acting on a box-shaped ship fixed in a harbor
- 30 June 2011
- Published by Springer Nature in Science China Technological Sciences
- Vol. 54 (8) , 2157-2166
Characteristic-based operator-splitting finite element method for Navier-Stokes equations
- 30 June 2011
- Published by Springer Nature in Science China Technological Sciences
- Vol. 54 (8) , 2157-2166
Characteristic-based operator-splitting finite element method for Navier-Stokes equations
- 6 December 2008
- Published by Springer Nature in Science China Technological Sciences
- Vol. 51 (12) , 2195-2206
A three-dimensional coupled numerical model of nonlinear waves in a harbor
- 6 December 2008
- Published by Springer Nature in Science China Technological Sciences
- Vol. 51 (12) , 2195-2206
A three-dimensional coupled numerical model of nonlinear waves in a harbor