M. V. Koteneva
Research Subjects
M. V. Koteneva has a total of 20 co-authors. Here are the top co-authors by number of shared publications:
S. A. Nikulin
National University of Science and Technology MISiS, Moscow, Russia
5 shared publicationsA. B. Rozhnov
MISIS National University of Science and Technology
4 shared publications- Aleksandr Aleksandrovich Komissarov
National University of Science and Technology “MISIS
2 shared publications - Aleksandr V. Kudrya
National University of Science and Technology MISiS, Moscow, Russia
2 shared publications National Research Technological University «MISIS»
2 shared publicationsA. V. Kydryashova
National University of Science and Technology (MISiS)
1 shared publication
Latest Publications
- 1 October 2023
- Published by Pleiades Publishing Ltd in Russian Metallurgy (Metally)
- Vol. 2023 (10) , 1482-1487
Influence of the Defects and Microstructure of the Oxide Films on Zirconium Alloys on Their Fracture during Loading
The defects and structure of the oxide films formed by the oxidation of tubular samples of E110 and E635 zirconium alloys in water and water with the addition of lithium are investigated. The crack sizes in the films before and after compression loading are quantitatively analyzed, and the kinetics of crack accumulation in the oxide films and the character of their fracture are analyzed. The initial defects are shown not to affect the fracture of the E635 alloy films during loading; however, along with a structure, they determine the fracture of the E110 alloy films.
- 1 October 2023
- Published by Pleiades Publishing Ltd in Russian Metallurgy (Metally)
- Vol. 2023 (10) , 1482-1487
Influence of the Defects and Microstructure of the Oxide Films on Zirconium Alloys on Their Fracture during Loading
The defects and structure of the oxide films formed by the oxidation of tubular samples of E110 and E635 zirconium alloys in water and water with the addition of lithium are investigated. The crack sizes in the films before and after compression loading are quantitatively analyzed, and the kinetics of crack accumulation in the oxide films and the character of their fracture are analyzed. The initial defects are shown not to affect the fracture of the E635 alloy films during loading; however, along with a structure, they determine the fracture of the E110 alloy films.
- 1 January 2023
- Published by Science & Technology in Deformation and Fracture of Materials
- No. 3s
Influence of imperfection and microstructure of oxide films of zirconium alloys on their destruction under loading
The imperfection and structure of oxide films obtained by oxidation of tubular samples of the E110 and E635 zirconium alloys in water and water with the addition of lithium have been studied. A quantitative analysis of crack sizes in films before and after compression loading was carried out, the kinetics of crack accumulation in oxide films and the nature of their destruction were analyzed. It is shown that the initial imperfection does not affect the process of destruction of films of the E635 alloy under loading, however, along with the structure it determines the destruction of films of the E110 alloy.
- 1 January 2023
- Published by Science & Technology in Deformation and Fracture of Materials
- No. 3s
Influence of imperfection and microstructure of oxide films of zirconium alloys on their destruction under loading
The imperfection and structure of oxide films obtained by oxidation of tubular samples of the E110 and E635 zirconium alloys in water and water with the addition of lithium have been studied. A quantitative analysis of crack sizes in films before and after compression loading was carried out, the kinetics of crack accumulation in oxide films and the nature of their destruction were analyzed. It is shown that the initial imperfection does not affect the process of destruction of films of the E635 alloy under loading, however, along with the structure it determines the destruction of films of the E110 alloy.
- 1 January 2023
- Published by Science & Technology in Deformation and Fracture of Materials
- No. 3s
Possibilities of "data mining" of production control in metallurgy for prediction of strength, ductility and toughness of metal products
The possibilities of a retrospective analysis of the production control database for predicting the level of strength, ductility and toughness of serial metal products have been evaluated. The boundaries of the effective application of regression, cognitive graphics techniques, parametric and non-parametric statistics (taking into account the type of distribution of values of control parameters) were revealed, which are necessary to search for significant relationships in the technology parameters - properties system and areas with a dominant type of dependence.
- 1 January 2023
- Published by Science & Technology in Deformation and Fracture of Materials
- No. 3s
Possibilities of "data mining" of production control in metallurgy for prediction of strength, ductility and toughness of metal products
The possibilities of a retrospective analysis of the production control database for predicting the level of strength, ductility and toughness of serial metal products have been evaluated. The boundaries of the effective application of regression, cognitive graphics techniques, parametric and non-parametric statistics (taking into account the type of distribution of values of control parameters) were revealed, which are necessary to search for significant relationships in the technology parameters - properties system and areas with a dominant type of dependence.
- 1 January 2023
- Published by Science & Technology in Deformation and Fracture of Materials
- No. 3s
Mechanical and corrosion properties of alloys of mg-zn-ga system after hot extrusion
The effect of hot extrusion on the mechanical and corrosion properties of alloys of the Mg-Zn-Ga system for medical purposes has been studied. It is shown that the Mg4Zn4Ga alloy has a favorable level of mechanical properties (σy = 343 MPa, σb = 256 MPa, δ = 14%) and a controlled corrosion rate (0.4 mm / year). The low cytotoxicity of the Mg4Zn4Ga alloy, determined in accordance with GOST R ISO 10993.5-99, makes possible to recommend it for further clinical trials in vivo and the manufacture of medical implants.
- 1 January 2023
- Published by Science & Technology in Deformation and Fracture of Materials
- No. 3s
Mechanical and corrosion properties of alloys of mg-zn-ga system after hot extrusion
The effect of hot extrusion on the mechanical and corrosion properties of alloys of the Mg-Zn-Ga system for medical purposes has been studied. It is shown that the Mg4Zn4Ga alloy has a favorable level of mechanical properties (σy = 343 MPa, σb = 256 MPa, δ = 14%) and a controlled corrosion rate (0.4 mm / year). The low cytotoxicity of the Mg4Zn4Ga alloy, determined in accordance with GOST R ISO 10993.5-99, makes possible to recommend it for further clinical trials in vivo and the manufacture of medical implants.
- 1 May 2018
- Published by Pleiades Publishing Ltd in Protection of Metals and Physical Chemistry of Surfaces
- Vol. 54 (3) , 477-483
The Influence of the Composition of a Heat-Transfer Agent on the Structure and Properties of Formed Oxide Films of Zirconium Alloys
The defectiveness and structure of oxide films were determined by transmission electron microscopy and scanning electron microscopy. Compression tests with the registration of acoustic emission of...
- 1 May 2018
- Published by Pleiades Publishing Ltd in Protection of Metals and Physical Chemistry of Surfaces
- Vol. 54 (3) , 477-483
The Influence of the Composition of a Heat-Transfer Agent on the Structure and Properties of Formed Oxide Films of Zirconium Alloys
The defectiveness and structure of oxide films were determined by transmission electron microscopy and scanning electron microscopy. Compression tests with the registration of acoustic emission of...
- 1 March 2016
- Published by Pleiades Publishing Ltd in Protection of Metals and Physical Chemistry of Surfaces
- Vol. 52 (2) , 316-322
The Influence of Oxidizing Medium on Structure, Mechanical Properties, and Breakage Pattern of Oxide Films of Zr—1% Nb Alloy under Conditions Simulating Oxidizing Media of WWER and PWR Reactors
- 1 March 2016
- Published by Pleiades Publishing Ltd in Protection of Metals and Physical Chemistry of Surfaces
- Vol. 52 (2) , 316-322
The Influence of Oxidizing Medium on Structure, Mechanical Properties, and Breakage Pattern of Oxide Films of Zr—1% Nb Alloy under Conditions Simulating Oxidizing Media of WWER and PWR Reactors
- 5 January 2014
- Published by Pleiades Publishing Ltd in Protection of Metals and Physical Chemistry of Surfaces
- Vol. 50 (1) , 64-68
Structure and mechanical properties of oxide films on zirconium alloys upon oxidation under different conditions
The structure and mechanical properties, as well as the mechanism and kinetics of the destruction of oxide films formed on tube specimens of E110 zirconium alloy based on electrolytic or sponge zirconium upon corrosion testing in an autoclave and high-temperature oxidation in steam (LOCA conditions), were studied with the use of transmission and scanning electron microscopy, microhardness measurements, acoustic emission, and fractography. Oxide films on specimens made of electrolytic zirconium upon testing in an autoclave are found to be composed of extended grains with a thickness of 100 nm, while those on sponge specimens are composed chiefly of equiaxial grains with a diameter of 30 nm. After high-temperature oxidation, the structure of oxide films consists of extended grains of a variable thickness, which increases from the surface to the film-metal boundary from 600 nm to 2.5 μm on specimens made of electrolytic zirconium and from 250 nm to 2 μm on sponge-zirconium specimens. The microhardness of films after testing in an autoclave is 1200 ± 50 HV on electrolytic zirconium and 2000 ± 50 HV on sponge zirconium. The hardness of films on sponge-zirconium specimens upon high-temperature oxidation is 1600 ± 50 HV. The combined analysis of deformation diagrams, fractures, and acoustic emission data showed that the destruction of thin oxide films after testing in an autoclave and that of thick films after high-temperature oxidation begins with the formation of transverse brittle ruptures at the same load of 12–15 MPa. The number of cracks in the films on specimens that underwent high-temperature oxidation increases under loading especially rapidly on electrolytic zirconium.
- 5 January 2014
- Published by Pleiades Publishing Ltd in Protection of Metals and Physical Chemistry of Surfaces
- Vol. 50 (1) , 64-68
Structure and mechanical properties of oxide films on zirconium alloys upon oxidation under different conditions
The structure and mechanical properties, as well as the mechanism and kinetics of the destruction of oxide films formed on tube specimens of E110 zirconium alloy based on electrolytic or sponge zirconium upon corrosion testing in an autoclave and high-temperature oxidation in steam (LOCA conditions), were studied with the use of transmission and scanning electron microscopy, microhardness measurements, acoustic emission, and fractography. Oxide films on specimens made of electrolytic zirconium upon testing in an autoclave are found to be composed of extended grains with a thickness of 100 nm, while those on sponge specimens are composed chiefly of equiaxial grains with a diameter of 30 nm. After high-temperature oxidation, the structure of oxide films consists of extended grains of a variable thickness, which increases from the surface to the film-metal boundary from 600 nm to 2.5 μm on specimens made of electrolytic zirconium and from 250 nm to 2 μm on sponge-zirconium specimens. The microhardness of films after testing in an autoclave is 1200 ± 50 HV on electrolytic zirconium and 2000 ± 50 HV on sponge zirconium. The hardness of films on sponge-zirconium specimens upon high-temperature oxidation is 1600 ± 50 HV. The combined analysis of deformation diagrams, fractures, and acoustic emission data showed that the destruction of thin oxide films after testing in an autoclave and that of thick films after high-temperature oxidation begins with the formation of transverse brittle ruptures at the same load of 12–15 MPa. The number of cracks in the films on specimens that underwent high-temperature oxidation increases under loading especially rapidly on electrolytic zirconium.
- 1 October 2012
- Published by Pleiades Publishing Ltd in Russian Metallurgy (Metally)
- Vol. 2012 (10) , 906-910
Effect of corrosion damages on the mechanical properties of zirconium alloy cladding tubes
The accumulation kinetics of corrosion-induced damages in zirconium alloy cladding tubes is studied during stress corrosion cracking tests. The effect of corrosion damages on the mechanical properties of the tubes in loading by internal pressure is analyzed.
- 1 October 2012
- Published by Pleiades Publishing Ltd in Russian Metallurgy (Metally)
- Vol. 2012 (10) , 906-910
Effect of corrosion damages on the mechanical properties of zirconium alloy cladding tubes
The accumulation kinetics of corrosion-induced damages in zirconium alloy cladding tubes is studied during stress corrosion cracking tests. The effect of corrosion damages on the mechanical properties of the tubes in loading by internal pressure is analyzed.