Ashish Kumar Sahu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Ashish Kumar Sahu has a total of 10 co-authors. Here are the top co-authors by number of shared publications:
- Sunil Jha
Department of Mechanical Engineering, Indian Institute of Technology Delhi, Hauz Khas, New Delhi, India
7 shared publications - Faiz Iqbal
School of Engineering and Physical Sciences, University of Lincoln, Brayford Pool, Lincoln LN6 7TS, UK
3 shared publications - Jitin Malhotra
Indian Institute of Technology Hauz Khas
2 shared publications Adepu Kumar
National Institute of Technology, Warangal
1 shared publication- Christ Prakash Paul
Raja Ramanna Centre for Advanced Technology, Indore, India
1 shared publication - H. A. Patel
Indian Institute of Technology Hauz Khas
1 shared publication
Latest Publications
- 12 October 2026
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part L: Journal of Materials: Design and Applications
Air-induced laser-assisted sequential micro-milling process for precise microchannel fabrication
Laser micromilling suffers from surface oxidation and spatter surrounding the machined zone. However, the micromilling process has drawbacks, including tool wear, high cutting forces, burr formation, and reduced tool life. To address these issues, this study proposes a novel hybrid method for fabricating 100 µm microchannels through an air-induced laser-assisted sequential micromilling (AILASMM) process, comprising laser milling followed by tool-based micromilling. To mitigate cutting forces, compressed air is introduced during laser machining to assist in effective material removal and to promote the formation of an oxidation layer, thereby reducing forces during the subsequent micromilling step. Results demonstrated that AILASMM significantly reduces (15–25%) the magnitude of the cutting forces with respect to conventional micromilling (CMM). In addition to that, the tool wear and burr formation were reduced (15–25%) in the former technique and produced a better surface finish. Milling at an increased feed rate increased the cutting forces. The burr size was also observed to increase (from 37 to 59 µm) as the feed rate increased (from 40 to 60 mm/min). AILASMM at a lower value of the spindle speed (20000 rpm), the surface finish improved to 0.6 µm, and the burr size was reduced to 20 µm. AILASMM produced small and fragmented chips, significantly reducing the tool's adhesion wear.
- 12 October 2026
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part L: Journal of Materials: Design and Applications
Air-induced laser-assisted sequential micro-milling process for precise microchannel fabrication
Laser micromilling suffers from surface oxidation and spatter surrounding the machined zone. However, the micromilling process has drawbacks, including tool wear, high cutting forces, burr formation, and reduced tool life. To address these issues, this study proposes a novel hybrid method for fabricating 100 µm microchannels through an air-induced laser-assisted sequential micromilling (AILASMM) process, comprising laser milling followed by tool-based micromilling. To mitigate cutting forces, compressed air is introduced during laser machining to assist in effective material removal and to promote the formation of an oxidation layer, thereby reducing forces during the subsequent micromilling step. Results demonstrated that AILASMM significantly reduces (15–25%) the magnitude of the cutting forces with respect to conventional micromilling (CMM). In addition to that, the tool wear and burr formation were reduced (15–25%) in the former technique and produced a better surface finish. Milling at an increased feed rate increased the cutting forces. The burr size was also observed to increase (from 37 to 59 µm) as the feed rate increased (from 40 to 60 mm/min). AILASMM at a lower value of the spindle speed (20000 rpm), the surface finish improved to 0.6 µm, and the burr size was reduced to 20 µm. AILASMM produced small and fragmented chips, significantly reducing the tool's adhesion wear.
- 1 April 2025
- Published by Taylor & Francis in Machining Science and Technology
- Vol. 29 (4) , 465-487
Modeling and simulation of ablated profile in laser micro-milling process of Ti6Al4V
- 1 April 2025
- Published by Taylor & Francis in Machining Science and Technology
- Vol. 29 (4) , 465-487
Modeling and simulation of ablated profile in laser micro-milling process of Ti6Al4V
- Open Access
- 23 September 2024
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 138 (1) , 17-30
Novel processing of micro-channels in micro-grinding with automated laser-assistance
Micro-structures are widely utilized in various fields such as optical, medical, defense, and aerospace. The accuracy and performance of micro-structures depend on fabrication methods, including conventional and non-conventional machining. High-quality micro-channel fabrication is challenging by conventional micro-grinding (CMG) which uses a micro-pencil grinding tool during micro-machining. However, in CMG, high-cutting forces act in the machining zone leading to tool deflection, tool failure, high temperature, and poor surface finish. The challenges of CMG can be overcome by using automated laser-assisted micro-grinding (LAMG), one of the modern micro-machining processes for fabricating high-quality, precise micro-channels. The novel processing of micro-channels in this work is through the in tandem use of LAMG and CMG. In this, the laser structuring is performed using LAMG followed by a micro-pencil grinding tool processing in a sequential manner on a same machine tool to achive high-quality parts and accuracy. This helps in fabrication of a micro-channel directly in one go without the need to remove the part to perform the two operations on two different machining setups, thereby reducing systematic fixturing errors which are significant when we are working at the micro-scale. This paper thus investigates the effect of various parameters viz. laser input energy densities and laser power on cutting forces and surface roughness on the tool as well as the work surface with two distinct scan patterns. In LAMG, at lower laser input energy density (pattern 1), the tangential and normal forces decreased by 10.3% and 20.5%, and surface roughness S a and S q reduced by 24% and 22% compared to CMG. Similarly, a normal force decreased by 20.5% in pattern 1 and 38% less in pattern 2. Still, the higher laser energy density (pattern 2) is unsuitable for structure due to an increase in S a and S q by 11% and 14.6%, respectively. Results have shown a maximum reduction in the normal and tangential force magnitude by 31 and 44% at 25 W compared to CMG. The work concludes that LAMG with novel laser assistance scan patterns has lower dynamic deflections resulting in better dimensional accuracy and surface finish compared to CMG with a lower tool.
- 23 September 2024
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 138 (1) , 17-30
Open AccessNovel processing of micro-channels in micro-grinding with automated laser-assistance
Micro-structures are widely utilized in various fields such as optical, medical, defense, and aerospace. The accuracy and performance of micro-structures depend on fabrication methods, including conventional and non-conventional machining. High-quality micro-channel fabrication is challenging by conventional micro-grinding (CMG) which uses a micro-pencil grinding tool during micro-machining. However, in CMG, high-cutting forces act in the machining zone leading to tool deflection, tool failure, high temperature, and poor surface finish. The challenges of CMG can be overcome by using automated laser-assisted micro-grinding (LAMG), one of the modern micro-machining processes for fabricating high-quality, precise micro-channels. The novel processing of micro-channels in this work is through the in tandem use of LAMG and CMG. In this, the laser structuring is performed using LAMG followed by a micro-pencil grinding tool processing in a sequential manner on a same machine tool to achive high-quality parts and accuracy. This helps in fabrication of a micro-channel directly in one go without the need to remove the part to perform the two operations on two different machining setups, thereby reducing systematic fixturing errors which are significant when we are working at the micro-scale. This paper thus investigates the effect of various parameters viz. laser input energy densities and laser power on cutting forces and surface roughness on the tool as well as the work surface with two distinct scan patterns. In LAMG, at lower laser input energy density (pattern 1), the tangential and normal forces decreased by 10.3% and 20.5%, and surface roughness S a and S q reduced by 24% and 22% compared to CMG. Similarly, a normal force decreased by 20.5% in pattern 1 and 38% less in pattern 2. Still, the higher laser energy density (pattern 2) is unsuitable for structure due to an increase in S a and S q by 11% and 14.6%, respectively. Results have shown a maximum reduction in the normal and tangential force magnitude by 31 and 44% at 25 W compared to CMG. The work concludes that LAMG with novel laser assistance scan patterns has lower dynamic deflections resulting in better dimensional accuracy and surface finish compared to CMG with a lower tool.
- Open Access
- 21 February 2024
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 136 (9) , 4007-4023
Quality enhancement of micro-milled channels with automated laser assistance
Microchannels are utilised on material surfaces of a body, allowing coolant to pass through them and enabling heat dissipation by increased contact area. Fabrication of metal surface microchannels is primarily achieved by employing a micro-milling process, which has drawbacks such as excessive cutting forces, top burrs, tool wear, and lower tool life. Alternatively, it is also realised by using Laser micro milling, which has problems associated with lower quality of surface finish, un-desired taper, heat-affected zone, and spatters. The existing literature, after due review of the current state of the art, has brought out gaps needing attention. These gaps are limited capability to reduce surface roughness, unaddressed burr width, and irregular bottom surface morphology, which affect microchannel quality. These gaps motivate this research work to improve and sustain the microchannel quality. To achieve the goals, this research work performs the fabrication of microchannels by micro-milling with automated laser assistance being achieved in two ways (a) sequentially, (b) non-sequentially, termed as LASMM and LPCMM, which are novel for the scientific community. The effects of micro milling parameters, spindle speed and feed on the quality were analysed while machining commercially pure titanium (cp-Ti). Results show that laser assistance to micro-milling provides a lower generation of undesired forces and lesser top burrs compared to micro-milling alone. In sequential laser assistance, the channels have a mean down burr width ~ 58% lower and a maximum down burr width ~ 38% lower than the channels done non-sequentially. In the case of up-burr width, a mean value ~ 60% lower and a maximum value ~ 73% lower is achieved in channels done non-sequentially as compared to those done sequentially. In the case of surface roughness, channels done sequentially have a maximum Sa value of 1.508 µm, a maximum Sq value of 1.912 µm whereas non-sequentially, they show a maximum Sa value of 3.495 µm, maximum Sq value of 4.59 µm. Steady tool wear is observed sequentially, whereas in non-sequential, rapid tool wear occurs after 500 mm of cutting length.
- 21 February 2024
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 136 (9) , 4007-4023
Open AccessQuality enhancement of micro-milled channels with automated laser assistance
Microchannels are utilised on material surfaces of a body, allowing coolant to pass through them and enabling heat dissipation by increased contact area. Fabrication of metal surface microchannels is primarily achieved by employing a micro-milling process, which has drawbacks such as excessive cutting forces, top burrs, tool wear, and lower tool life. Alternatively, it is also realised by using Laser micro milling, which has problems associated with lower quality of surface finish, un-desired taper, heat-affected zone, and spatters. The existing literature, after due review of the current state of the art, has brought out gaps needing attention. These gaps are limited capability to reduce surface roughness, unaddressed burr width, and irregular bottom surface morphology, which affect microchannel quality. These gaps motivate this research work to improve and sustain the microchannel quality. To achieve the goals, this research work performs the fabrication of microchannels by micro-milling with automated laser assistance being achieved in two ways (a) sequentially, (b) non-sequentially, termed as LASMM and LPCMM, which are novel for the scientific community. The effects of micro milling parameters, spindle speed and feed on the quality were analysed while machining commercially pure titanium (cp-Ti). Results show that laser assistance to micro-milling provides a lower generation of undesired forces and lesser top burrs compared to micro-milling alone. In sequential laser assistance, the channels have a mean down burr width ~ 58% lower and a maximum down burr width ~ 38% lower than the channels done non-sequentially. In the case of up-burr width, a mean value ~ 60% lower and a maximum value ~ 73% lower is achieved in channels done non-sequentially as compared to those done sequentially. In the case of surface roughness, channels done sequentially have a maximum Sa value of 1.508 µm, a maximum Sq value of 1.912 µm whereas non-sequentially, they show a maximum Sa value of 3.495 µm, maximum Sq value of 4.59 µm. Steady tool wear is observed sequentially, whereas in non-sequential, rapid tool wear occurs after 500 mm of cutting length.
- Open Access
- 12 November 2021
- Published by Springer Nature in Research Square
Laser Assisted Micro Grinding of Titanium
Laser assisted micro-grinding (LAMG) is an emerging area of research in the field of high-quality micro-job fabrication and performance improvement. Conventional micro grinding (CMG) by micro pencil grinding tool suffers drawbacks such as tool deflection, higher cutting force and poor surface finish. In the present work, authors have attempted to investigate the performance of LAMG and CMG in the fabrication of micro-channel on Titanium material. Surface of workpiece was structured with the help of air assisted nanosecond-pulsed fiber laser scanning prior to the CMG at the different values of laser power by keeping scanning velocity constant. During the study, the CMG forces were recorded and after the processes surface roughness of the fabricated microchannels was measured. Results have shown reduction in the magnitude of the normal and tangential force by 31 % and 44 %, respectively, in LAMG compared to the CMG. In addition to that better surface finish was observed in LAMG than CMG. The surface roughness of micro-channel and grinding forces were found to be dependent on the power density of laser. Increase in the laser power deteriorates the surface finish and reduces the magnitude of grinding forces. High grinding forces in the CMG led to the dynamic deflection of the grinding wheel which produced the vibration in the process. The excessive vibration in CMG processes exploited the surface finish of the micro-channel. Such vibration was not observed on the LAMG process; as a result, better dimensional accuracy and surface finish of the channel was found.
- 12 November 2021
- Published by Springer Nature in Research Square
Open AccessLaser Assisted Micro Grinding of Titanium
Laser assisted micro-grinding (LAMG) is an emerging area of research in the field of high-quality micro-job fabrication and performance improvement. Conventional micro grinding (CMG) by micro pencil grinding tool suffers drawbacks such as tool deflection, higher cutting force and poor surface finish. In the present work, authors have attempted to investigate the performance of LAMG and CMG in the fabrication of micro-channel on Titanium material. Surface of workpiece was structured with the help of air assisted nanosecond-pulsed fiber laser scanning prior to the CMG at the different values of laser power by keeping scanning velocity constant. During the study, the CMG forces were recorded and after the processes surface roughness of the fabricated microchannels was measured. Results have shown reduction in the magnitude of the normal and tangential force by 31 % and 44 %, respectively, in LAMG compared to the CMG. In addition to that better surface finish was observed in LAMG than CMG. The surface roughness of micro-channel and grinding forces were found to be dependent on the power density of laser. Increase in the laser power deteriorates the surface finish and reduces the magnitude of grinding forces. High grinding forces in the CMG led to the dynamic deflection of the grinding wheel which produced the vibration in the process. The excessive vibration in CMG processes exploited the surface finish of the micro-channel. Such vibration was not observed on the LAMG process; as a result, better dimensional accuracy and surface finish of the channel was found.
- 3 February 2020
- Published by Taylor & Francis in Materials and Manufacturing Processes
- Vol. 35 (3) , 279-290
Microchannel fabrication and metallurgical characterization on titanium by nanosecond fiber laser micromilling
Laser micromilling technique is used to manufacture microchannel on metals and nonmetals. Microfeatures ≤100 µm are still challenging for fabrication by common methods. Nanosecond fiber laser micromachining has become more popular owing to its prospective implementation in laser micromilling. Microchannel application relies on its geometric dimension, profile, and surface quality. In this study, an attempt was made to explore the impact of process parameters scanning times, scanning velocity, pulse repetition rate, and assist gas pressure on top kerf width, taper, surface roughness, and metal removal rate in laser micromilling experimentally. Microchannel width varied between 45.5 and 70.9 µm. A regression model has been developed for each response. ANOVA (analysis of variance) has been carried out to remove insignificant parameters. Thermal stress analyzed by surface cracks inside microchannel by Scanning Electrone Microscopy (SEM) images. Higher PRR, lower no. of scans, higher scanning speed and high air pressure found suitable for lesser surface cracks. Redeposition observed at slower scanning velocity and minimum scanning times. Oxidation zone from boundary of channel varies between 37 and 58 µm. Oxide formed on Ti surface which increases oxygen content toward center of channel from 51.08 to 76.22% compared to outside surroundings.
- 3 February 2020
- Published by Taylor & Francis in Materials and Manufacturing Processes
- Vol. 35 (3) , 279-290
Microchannel fabrication and metallurgical characterization on titanium by nanosecond fiber laser micromilling
Laser micromilling technique is used to manufacture microchannel on metals and nonmetals. Microfeatures ≤100 µm are still challenging for fabrication by common methods. Nanosecond fiber laser micromachining has become more popular owing to its prospective implementation in laser micromilling. Microchannel application relies on its geometric dimension, profile, and surface quality. In this study, an attempt was made to explore the impact of process parameters scanning times, scanning velocity, pulse repetition rate, and assist gas pressure on top kerf width, taper, surface roughness, and metal removal rate in laser micromilling experimentally. Microchannel width varied between 45.5 and 70.9 µm. A regression model has been developed for each response. ANOVA (analysis of variance) has been carried out to remove insignificant parameters. Thermal stress analyzed by surface cracks inside microchannel by Scanning Electrone Microscopy (SEM) images. Higher PRR, lower no. of scans, higher scanning speed and high air pressure found suitable for lesser surface cracks. Redeposition observed at slower scanning velocity and minimum scanning times. Oxidation zone from boundary of channel varies between 37 and 58 µm. Oxide formed on Ti surface which increases oxygen content toward center of channel from 51.08 to 76.22% compared to outside surroundings.
- 2 February 2020
- Published by Springer Nature
- p. 983-989
Numerical Modelling of High Energy Density Beam-Assisted Machining of Hardened Armour Steel
- 2 February 2020
- Published by Springer Nature
- p. 983-989
Numerical Modelling of High Energy Density Beam-Assisted Machining of Hardened Armour Steel
- 1 December 2019
- Published by Springer Nature
- p. 371-380
Experimental Study of Nanosecond Fiber Laser Micromilling of Ti6Al4V Alloy
- 1 December 2019
- Published by Springer Nature
- p. 371-380
Experimental Study of Nanosecond Fiber Laser Micromilling of Ti6Al4V Alloy
- 24 November 2019
- Published by Springer Nature
- p. 637-647
A Cyber-Physical System Architecture for Smart Manufacturing
- 24 November 2019
- Published by Springer Nature
- p. 637-647
A Cyber-Physical System Architecture for Smart Manufacturing