Svetlana Yu. Khashirova
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Svetlana Yu. Khashirova has a total of 85 co-authors. Here are the top co-authors by number of shared publications:
- Azamat Aslanovich Zhansitov
Center for Progressive Materials and Additive Technologies, Kabardino-Balkarian State University Named after H.M. Berbekov, 360004 Nalchik, Russia
14 shared publications - Azamat Slonov
Center for Progressive Materials and Additive Technologies, Kabardino-Balkarian State University Named after H.M. Berbekov, 360004 Nalchik, Russia
9 shared publications - Ilya L. Borisov
Center for Progressive Materials and Additive Technologies, Kabardino-Balkarian State University Named after H.M. Berbekov, 360004 Nalchik, Russia
6 shared publications - Kamila Shakhmurzova
Center for Progressive Materials and Additive Technologies, Kabardino-Balkarian State University Named after H.M. Berbekov, 360004 Nalchik, Russia
6 shared publications - Zhanna Kurdanova
Center for Progressive Materials and Additive Technologies, Kabardino-Balkarian State University Named after H.M. Berbekov, 360004 Nalchik, Russia
6 shared publications - Ismel Musov
Center for Progressive Materials and Additive Technologies, Kabardino-Balkarian State University Named after H.M. Berbekov, 360004 Nalchik, Russia
5 shared publications
Latest Publications
- Open Access
- 21 August 2026
- Published by Federal Medical Biological Agency
In vitro screening of biocompatibility of modified polyetheretherketone as an implant material: Cytotoxicity and cell adhesion
In vitro screening of biocompatibility of modified polyetheretherketone as an implant material: Cytotoxicity and cell adhesion | Khashirov | Extreme Medicine Скрининг in vitro биосовместимости модифицированного полиэфирэфиркетона как материала для имплантатов: цитотоксичность и клеточная адгезия | Хаширов | Экстремальная биомедицина
- 21 August 2026
- Published by Federal Medical Biological Agency
Open AccessIn vitro screening of biocompatibility of modified polyetheretherketone as an implant material: Cytotoxicity and cell adhesion
In vitro screening of biocompatibility of modified polyetheretherketone as an implant material: Cytotoxicity and cell adhesion | Khashirov | Extreme Medicine Скрининг in vitro биосовместимости модифицированного полиэфирэфиркетона как материала для имплантатов: цитотоксичность и клеточная адгезия | Хаширов | Экстремальная биомедицина
- Open Access
- 26 March 2026
- Published by MDPI AG in Agriengineering
- Vol. 8 (4) , 120
Electromagnetic Priming Modulates Gas Exchange During Pea Seed Germination Under Salt Stress
Electromagnetic treatment (EMF) can stimulate seed germination and plant development, including mitigating the negative effects of stressors. One non-invasive approach to detecting the early effects of EMF exposure is the study of gas exchange dynamics during the seed imbibition stage. Gas chromatography was used to assess the effect of low-intensity non-thermal EMF on the concentration of H2, O2, CO2, and NH3 gases in the “soil–pea seed” system under optimal conditions and under salt stress. EMF treatment exhibited a variant-dependent effect. Under optimal conditions, it stimulated respiration (O2 concentration decreased by 12%, CO2 increased by 15%); under salinity, the concentration of both gases decreased by 8–10% relative to the control. H2 emission proved to be a sensitive biochemical marker of the response to external factors. Under optimal conditions, EMF treatment nearly tripled H2 emission and shifted its emission peak one day earlier, which may indicate accelerated mobilization of the seed’s defense systems under developing hypoxia. Salinity reduced H2 levels by an order of magnitude, while EMF treatment stabilized the H2 emission rate, reducing it by almost half. Thus, EMF should be regarded as a modifier of the seed’s metabolic response to imbibition conditions, rather than solely as a germination stimulant.
- 26 March 2026
- Published by MDPI AG in Agriengineering
- Vol. 8 (4) , 120
Open AccessElectromagnetic Priming Modulates Gas Exchange During Pea Seed Germination Under Salt Stress
Electromagnetic treatment (EMF) can stimulate seed germination and plant development, including mitigating the negative effects of stressors. One non-invasive approach to detecting the early effects of EMF exposure is the study of gas exchange dynamics during the seed imbibition stage. Gas chromatography was used to assess the effect of low-intensity non-thermal EMF on the concentration of H2, O2, CO2, and NH3 gases in the “soil–pea seed” system under optimal conditions and under salt stress. EMF treatment exhibited a variant-dependent effect. Under optimal conditions, it stimulated respiration (O2 concentration decreased by 12%, CO2 increased by 15%); under salinity, the concentration of both gases decreased by 8–10% relative to the control. H2 emission proved to be a sensitive biochemical marker of the response to external factors. Under optimal conditions, EMF treatment nearly tripled H2 emission and shifted its emission peak one day earlier, which may indicate accelerated mobilization of the seed’s defense systems under developing hypoxia. Salinity reduced H2 levels by an order of magnitude, while EMF treatment stabilized the H2 emission rate, reducing it by almost half. Thus, EMF should be regarded as a modifier of the seed’s metabolic response to imbibition conditions, rather than solely as a germination stimulant.
- Open Access
- 4 March 2026
- Published by Publishing House OKI in Antibiot Khimioter = Antibiotics and Chemotherapy
- Vol. 70 (11-12) , 92-99
Dietary Sources of Hormones and Their Impact on Human Physiological State: An Analytical Review
Exogenous and endogenous hormones are found in many foods — from steroid implants and recombinant growth factors used in livestock and dairy production to natural hormones present in animal products. Due to the growing incidence of endocrine and reproductive diseases, an analysis of current data on the way dietary hormones affect human physiology and health was conducted. These substances include synthetic growth promoters, animal steroids, and plant phytoestrogens, which can enter the human diet through the consumption of meat, dairy, and soy products. The mechanisms of action of hormonal substances on the human body were examined, as well as data on endocrine disruption, cancer risk, and reproductive outcomes. Epidemiological and experimental studies have found associations between dietary hormone consumption and endocrine disruption, changes in the timing of puberty and fertility, metabolic dysfunctions, and hormone-dependent cancers. The complexity of this topic lies in the lack of consensus on the relationship between the consumption of hormone-containing products and the development of these diseases, resulting in varying approaches to regulating intake levels across countries. Therefore, this review provides an overview of global regulatory limits for hormone content in foods, examines the types and origins of these compounds, summarizes data on their impact on human and animal health, as well as discusses the risks and prospects of long-term consumption of endocrine disruptors.
- 4 March 2026
- Published by Publishing House OKI in Antibiot Khimioter = Antibiotics and Chemotherapy
- Vol. 70 (11-12) , 92-99
Open AccessDietary Sources of Hormones and Their Impact on Human Physiological State: An Analytical Review
Exogenous and endogenous hormones are found in many foods — from steroid implants and recombinant growth factors used in livestock and dairy production to natural hormones present in animal products. Due to the growing incidence of endocrine and reproductive diseases, an analysis of current data on the way dietary hormones affect human physiology and health was conducted. These substances include synthetic growth promoters, animal steroids, and plant phytoestrogens, which can enter the human diet through the consumption of meat, dairy, and soy products. The mechanisms of action of hormonal substances on the human body were examined, as well as data on endocrine disruption, cancer risk, and reproductive outcomes. Epidemiological and experimental studies have found associations between dietary hormone consumption and endocrine disruption, changes in the timing of puberty and fertility, metabolic dysfunctions, and hormone-dependent cancers. The complexity of this topic lies in the lack of consensus on the relationship between the consumption of hormone-containing products and the development of these diseases, resulting in varying approaches to regulating intake levels across countries. Therefore, this review provides an overview of global regulatory limits for hormone content in foods, examines the types and origins of these compounds, summarizes data on their impact on human and animal health, as well as discusses the risks and prospects of long-term consumption of endocrine disruptors.
- Open Access
Novel Low-Crystallinity Polyetheretherketone Copolymers for 3D Printing
To improve the quality of additive manufacturing of PEEK parts, copolymers with varying 4,4′-dichlorodiphenylsulfone (DCDPS) contents were synthesized. A study of the thermophysical properties of the resulting copolymers revealed that increasing the DCDPS content leads to lower melting temperatures, crystallization temperatures, and degree of crystallinity, while simultaneously increasing the glass transition temperature. It was found that structural amorphization leads to a predictable decrease in the strength and elastic modulus of both cast and printed samples. However, at a DCDPS concentration of 15%, the decrease in mechanical properties is offset by an increase in polymer chain rigidity. The practical result of this study was the successful adaptation of the material to FDM printing: copolymers with DCDPS contents in the range of 5–20% ensured stable molding without deformation or delamination, demonstrating an optimal balance between processability and performance.
Open AccessNovel Low-Crystallinity Polyetheretherketone Copolymers for 3D Printing
To improve the quality of additive manufacturing of PEEK parts, copolymers with varying 4,4′-dichlorodiphenylsulfone (DCDPS) contents were synthesized. A study of the thermophysical properties of the resulting copolymers revealed that increasing the DCDPS content leads to lower melting temperatures, crystallization temperatures, and degree of crystallinity, while simultaneously increasing the glass transition temperature. It was found that structural amorphization leads to a predictable decrease in the strength and elastic modulus of both cast and printed samples. However, at a DCDPS concentration of 15%, the decrease in mechanical properties is offset by an increase in polymer chain rigidity. The practical result of this study was the successful adaptation of the material to FDM printing: copolymers with DCDPS contents in the range of 5–20% ensured stable molding without deformation or delamination, demonstrating an optimal balance between processability and performance.
- Open Access
Polyphenylene Sulfide-Based Compositions with Solid Fillers for Powder Injection Molding
Powder Injection Molding (PIM) is a versatile manufacturing technology widely used for fabricating components with complex geometries from metals and ceramics, yet its application to high-performance thermoplastics remains underutilized. This study explores the feasibility of manufacturing products from Polyphenylene Sulfide (PPS)—a promising linear aromatic polymer synthesized in powder form—using PIM technology and investigates the development of PE-based feedstocks with PPS and solid fillers. Regarding the matrix formulation, it was found that using pure paraffin as a binder limited the maximum PPS content to 20%. Consequently, a modified binder system consisting of Low-Density Polyethylene (LDPE) and paraffin in a 70:30 wt.% ratio was utilized, which successfully increased the PPS loading in the feedstock to 50% and enabled stable molding. Following matrix optimization, the study examined composites incorporating various fillers, including chalk, talc, and carbon fibers. Systematic rheological analysis confirmed that these composite suspensions possess characteristics necessary for molding products with complex geometries. Key results indicate that optimal sintering conditions were established to achieve the required mechanical properties. Among the tested fillers, carbon fibers were the most effective reinforcement, increasing the elastic modulus by 33% and flexural strength by 20%. Representative examples of samples successfully manufactured via this approach are presented.
Open AccessPolyphenylene Sulfide-Based Compositions with Solid Fillers for Powder Injection Molding
Powder Injection Molding (PIM) is a versatile manufacturing technology widely used for fabricating components with complex geometries from metals and ceramics, yet its application to high-performance thermoplastics remains underutilized. This study explores the feasibility of manufacturing products from Polyphenylene Sulfide (PPS)—a promising linear aromatic polymer synthesized in powder form—using PIM technology and investigates the development of PE-based feedstocks with PPS and solid fillers. Regarding the matrix formulation, it was found that using pure paraffin as a binder limited the maximum PPS content to 20%. Consequently, a modified binder system consisting of Low-Density Polyethylene (LDPE) and paraffin in a 70:30 wt.% ratio was utilized, which successfully increased the PPS loading in the feedstock to 50% and enabled stable molding. Following matrix optimization, the study examined composites incorporating various fillers, including chalk, talc, and carbon fibers. Systematic rheological analysis confirmed that these composite suspensions possess characteristics necessary for molding products with complex geometries. Key results indicate that optimal sintering conditions were established to achieve the required mechanical properties. Among the tested fillers, carbon fibers were the most effective reinforcement, increasing the elastic modulus by 33% and flexural strength by 20%. Representative examples of samples successfully manufactured via this approach are presented.
- Open Access
Synthesis and Properties of Polyarylene Ether Nitrile and Polyphenylene Sulfone Copolymers
Copolymers of polyphenylene sulfone and polyarylene ether nitrile were synthesized using nucleophilic polycondensation. 2,6-difluorobenzonitrile (DFBN), 4,4′-dihydroxybiphenyl, and 4,4′-dichlorodiphenyl sulfone were used as monomers. The structure of the obtained copolymers was confirmed by means of IR spectroscopy, and their solubility in various solvents was studied. Thermal properties were studied using differential scanning calorimetry (DSC) and thermogravimetric analysis, as well as a set of basic mechanical properties. It was found that both thermal stability and glass transition temperature are virtually independent of the copolymer composition, while samples with a DFBN monomer content of more than 75% exhibit a melting peak in the region of 357 °C on the DSC curves, indicating an increase in the degree of crystallinity, accompanied by a deterioration in the solubility of these polymers. With increasing DFBN content, a uniform increase in elastic modulus is observed, and both bending and tensile strength increase significantly. However, the introduction of DFBN segments into the polyphenylene sulfone structure leads to a decrease in impact strength.
Open AccessSynthesis and Properties of Polyarylene Ether Nitrile and Polyphenylene Sulfone Copolymers
Copolymers of polyphenylene sulfone and polyarylene ether nitrile were synthesized using nucleophilic polycondensation. 2,6-difluorobenzonitrile (DFBN), 4,4′-dihydroxybiphenyl, and 4,4′-dichlorodiphenyl sulfone were used as monomers. The structure of the obtained copolymers was confirmed by means of IR spectroscopy, and their solubility in various solvents was studied. Thermal properties were studied using differential scanning calorimetry (DSC) and thermogravimetric analysis, as well as a set of basic mechanical properties. It was found that both thermal stability and glass transition temperature are virtually independent of the copolymer composition, while samples with a DFBN monomer content of more than 75% exhibit a melting peak in the region of 357 °C on the DSC curves, indicating an increase in the degree of crystallinity, accompanied by a deterioration in the solubility of these polymers. With increasing DFBN content, a uniform increase in elastic modulus is observed, and both bending and tensile strength increase significantly. However, the introduction of DFBN segments into the polyphenylene sulfone structure leads to a decrease in impact strength.
- Open Access
- 6 January 2026
- Published by Kazan Federal University in Uchenye Zapiski Kazanskogo Universiteta. Seriya Estestvennye Nauki
- Vol. 167 (4) , 644-657
Effect of steam sterilization on the morphology and mechanical properties of polyphenylene sulfone hollow fiber membranes
Влияние паровой стерилизации на морфологию и механические свойства половолоконных мембран из полифениленсульфона
- 6 January 2026
- Published by Kazan Federal University in Uchenye Zapiski Kazanskogo Universiteta. Seriya Estestvennye Nauki
- Vol. 167 (4) , 644-657
Open AccessEffect of steam sterilization on the morphology and mechanical properties of polyphenylene sulfone hollow fiber membranes
Влияние паровой стерилизации на морфологию и механические свойства половолоконных мембран из полифениленсульфона
- Open Access
Increasing the Permeability of Polyphenylene Sulfone Hollow Fiber Ultrafiltration Membranes by Switching the Polymer End Groups
The influence of the molecular weight and chemical structure of polyphenylene sulfone (PPSU) end groups on the formation of the porous structure of ultrafiltration (UF) hollow fiber membranes was investigated. Polymers with a molecular weight ranging from 67 to 81 kg/mol and with a hydroxyl-to-chlorine end group ratio ranging from 0.43 to 17.0 were synthesized. The excess of end groups was achieved during polymer synthesis by adding one of the following monomers: hydroxyl (excess DHBP) or chlorine (excess DCDPS). For the first time, it was found that the stability of PPSU solutions is determined not by the molecular weight of the polymer, but by the chemical structure of its end groups. The stability of polymer solutions increases with the increasing proportion of chlorine groups. The SEM method showed that with the increasing molar fraction of chlorine end groups in the polymer, a more open porous structure forms on the outer surface of the hollow fiber membranes derived from it. The maximum UF permeance of the hollow fiber membranes for water was achieved with the PPSU sample containing the highest chlorine end group content, amounting to 136 L/(m2·h·bar), with a high rejection of the model substance Blue Dextran (at 94.7%). This represents the best result currently reported among unmodified PPSU hollow fiber membranes.
Open AccessIncreasing the Permeability of Polyphenylene Sulfone Hollow Fiber Ultrafiltration Membranes by Switching the Polymer End Groups
The influence of the molecular weight and chemical structure of polyphenylene sulfone (PPSU) end groups on the formation of the porous structure of ultrafiltration (UF) hollow fiber membranes was investigated. Polymers with a molecular weight ranging from 67 to 81 kg/mol and with a hydroxyl-to-chlorine end group ratio ranging from 0.43 to 17.0 were synthesized. The excess of end groups was achieved during polymer synthesis by adding one of the following monomers: hydroxyl (excess DHBP) or chlorine (excess DCDPS). For the first time, it was found that the stability of PPSU solutions is determined not by the molecular weight of the polymer, but by the chemical structure of its end groups. The stability of polymer solutions increases with the increasing proportion of chlorine groups. The SEM method showed that with the increasing molar fraction of chlorine end groups in the polymer, a more open porous structure forms on the outer surface of the hollow fiber membranes derived from it. The maximum UF permeance of the hollow fiber membranes for water was achieved with the PPSU sample containing the highest chlorine end group content, amounting to 136 L/(m2·h·bar), with a high rejection of the model substance Blue Dextran (at 94.7%). This represents the best result currently reported among unmodified PPSU hollow fiber membranes.
- Open Access
High-Performance Porous Supports Based on Hydroxyl-Terminated Polysulfone and CO2/CO-Selective Composite Membranes
The scope of this work was to develop a thin-film composite (TFC) membrane for the separation of CO2/CO mixtures, which are relevant for many processes of gas processing and gasification of carbon-based feedstock. Special attention was given to the development of highly permeable porous polysulfone (PSF) supports (more than 26,000 GPU for CO2) since both the selective and support layers contribute significantly to the overall performance of the TFC membrane. The PSF porous support is widely used in commercial and lab-scale TFC membranes, and its porous structure and other exploitation parameters are set during the non-solvent-induced phase separation (NIPS) process. Since the casting solution properties (e.g., viscosity) and the interactions in a three-component system (polymer, solvent, and non-solvent) play noticeable roles in the NIPS process, polysulfone samples in a wide range of molecular weights (Mw = 76,000–122,000 g·mol−1) with terminal hydroxyl groups were synthesized for the first time. Commercial PSF with predominantly terminal chlorine groups (Ultrason® S 6010) was used as a reference. The PSF samples were characterized by NMR, DSC, and TGA methods, and the Hansen solubility parameters were calculated. It was found that increasing the ratio of terminal –OH over –Cl groups improved the “solubility” of PSF in N-methyl-2-pyrrolidone (NMP) and water. A direct dependence of the gas permeance of porous supports on the coagulation rate of the casting solution was identified for the first time. It was shown that the use of synthesized PSF (Mw = 76,000 g·mol−1, Mw/Mn = 3.0, (–OH):(–Cl) ratio of 4.7:1) enabled a porous support with a CO2 permeance of 26,700 GPU to be obtained, while the support formed from a commercial PSF Ultrason® S 6010 (Mw = 68,000 g·mol−1, Mw/Mn = 1.7, (–OH):(–Cl) ratio of 1:1.9) under the same conditions demonstrated 4300 GPU. The siloxane-based materials were used for the selective layer since the thin films based on rubbery polymers do not undergo the same accelerating physical aging as glassy polymers. Two types of materials were screened for the selective layer: synthesized polymethyltrifluoroethylacrylate siloxane-polydecylmethylsiloxane (50F3) copolymer, and polydimethylsiloxane (PDMS). 50F3 siloxane was studied for gas separation applications for the first time. It was shown that the permeance of composite membranes based on high-performance porous supports from the PSF samples synthesized was 3.5 times higher than that from similar composite membranes based on supports from a commercial Ultrason® S 6010 PSF with a permeance value of 4300 GPU for CO2. It was found that the enhanced gas permeance of composite membranes based on the highly permeable porous PSF supports developed was observed for both 50F3 polysiloxane and commercial PDMS. At the same time, the CO2/CO selectivity of the composite membranes with a 50F3-selective layer (9.1–9.3) is 1.5 times higher than that of composite membranes with a PDMS-selective layer. This makes the F-containing 50F3 polysiloxane a promising polymer for CO2/CO separation.
Open AccessHigh-Performance Porous Supports Based on Hydroxyl-Terminated Polysulfone and CO2/CO-Selective Composite Membranes
The scope of this work was to develop a thin-film composite (TFC) membrane for the separation of CO2/CO mixtures, which are relevant for many processes of gas processing and gasification of carbon-based feedstock. Special attention was given to the development of highly permeable porous polysulfone (PSF) supports (more than 26,000 GPU for CO2) since both the selective and support layers contribute significantly to the overall performance of the TFC membrane. The PSF porous support is widely used in commercial and lab-scale TFC membranes, and its porous structure and other exploitation parameters are set during the non-solvent-induced phase separation (NIPS) process. Since the casting solution properties (e.g., viscosity) and the interactions in a three-component system (polymer, solvent, and non-solvent) play noticeable roles in the NIPS process, polysulfone samples in a wide range of molecular weights (Mw = 76,000–122,000 g·mol−1) with terminal hydroxyl groups were synthesized for the first time. Commercial PSF with predominantly terminal chlorine groups (Ultrason® S 6010) was used as a reference. The PSF samples were characterized by NMR, DSC, and TGA methods, and the Hansen solubility parameters were calculated. It was found that increasing the ratio of terminal –OH over –Cl groups improved the “solubility” of PSF in N-methyl-2-pyrrolidone (NMP) and water. A direct dependence of the gas permeance of porous supports on the coagulation rate of the casting solution was identified for the first time. It was shown that the use of synthesized PSF (Mw = 76,000 g·mol−1, Mw/Mn = 3.0, (–OH):(–Cl) ratio of 4.7:1) enabled a porous support with a CO2 permeance of 26,700 GPU to be obtained, while the support formed from a commercial PSF Ultrason® S 6010 (Mw = 68,000 g·mol−1, Mw/Mn = 1.7, (–OH):(–Cl) ratio of 1:1.9) under the same conditions demonstrated 4300 GPU. The siloxane-based materials were used for the selective layer since the thin films based on rubbery polymers do not undergo the same accelerating physical aging as glassy polymers. Two types of materials were screened for the selective layer: synthesized polymethyltrifluoroethylacrylate siloxane-polydecylmethylsiloxane (50F3) copolymer, and polydimethylsiloxane (PDMS). 50F3 siloxane was studied for gas separation applications for the first time. It was shown that the permeance of composite membranes based on high-performance porous supports from the PSF samples synthesized was 3.5 times higher than that from similar composite membranes based on supports from a commercial Ultrason® S 6010 PSF with a permeance value of 4300 GPU for CO2. It was found that the enhanced gas permeance of composite membranes based on the highly permeable porous PSF supports developed was observed for both 50F3 polysiloxane and commercial PDMS. At the same time, the CO2/CO selectivity of the composite membranes with a 50F3-selective layer (9.1–9.3) is 1.5 times higher than that of composite membranes with a PDMS-selective layer. This makes the F-containing 50F3 polysiloxane a promising polymer for CO2/CO separation.
- Open Access
The Rheology of Polyether Ether Ketone Concentrated Suspensions for Powder Molding and 3D Printing
The main goal of the work was to use rheological methods for assessing the properties of a composition based on polyether ether ketone (PEEK) to determine the concentration limits of the polymer in the composition and select the optimal content of this composition for powder molding. The rheological properties of highly filled suspensions based on PEEK and paraffin, as well as in paraffin–polyethylene mixtures at various component ratios, were studied. These materials are designed for powder injection molding and 3D printing. Suspensions with a PEEK powder content above 50% are not capable of flow and, with increasing pressure, slide along the surface of the channel. For compositions with a higher content (60 and 70 vol.%) PEEK, independence of the storage modulus from frequency is observed, which is typical for solids and confirms the assignment of such suspensions to elastic–plastic media. The introduction of high-density polyethylene into the composition helps improve the technological properties of suspensions, expanding the range of fluidity, although it leads to an increase in viscosity. In suspensions with a mixed composition of the liquid phase, with increasing temperature, a decrease in the storage modulus is observed at 120 °C and, on the contrary, an increase at 180 °C. The latter may be a consequence of the evaporation of paraffin and the softening of PEEK due to the approach to the glass transition temperature of the polymer. Suspensions with 40% PEEK content have an optimal set of rheological properties for powder injection molding. A 3D printing filament was also obtained from a composition with 40% PEEK, which had good technological properties for FDM 3D printing. Products of satisfactory quality from suspensions with 50% PEEK can be produced by powder injection molding, but not by 3D printing. The selected compositions were used to obtain real PEEK products for practical applications.
Open AccessThe Rheology of Polyether Ether Ketone Concentrated Suspensions for Powder Molding and 3D Printing
The main goal of the work was to use rheological methods for assessing the properties of a composition based on polyether ether ketone (PEEK) to determine the concentration limits of the polymer in the composition and select the optimal content of this composition for powder molding. The rheological properties of highly filled suspensions based on PEEK and paraffin, as well as in paraffin–polyethylene mixtures at various component ratios, were studied. These materials are designed for powder injection molding and 3D printing. Suspensions with a PEEK powder content above 50% are not capable of flow and, with increasing pressure, slide along the surface of the channel. For compositions with a higher content (60 and 70 vol.%) PEEK, independence of the storage modulus from frequency is observed, which is typical for solids and confirms the assignment of such suspensions to elastic–plastic media. The introduction of high-density polyethylene into the composition helps improve the technological properties of suspensions, expanding the range of fluidity, although it leads to an increase in viscosity. In suspensions with a mixed composition of the liquid phase, with increasing temperature, a decrease in the storage modulus is observed at 120 °C and, on the contrary, an increase at 180 °C. The latter may be a consequence of the evaporation of paraffin and the softening of PEEK due to the approach to the glass transition temperature of the polymer. Suspensions with 40% PEEK content have an optimal set of rheological properties for powder injection molding. A 3D printing filament was also obtained from a composition with 40% PEEK, which had good technological properties for FDM 3D printing. Products of satisfactory quality from suspensions with 50% PEEK can be produced by powder injection molding, but not by 3D printing. The selected compositions were used to obtain real PEEK products for practical applications.