S. V. S. Narayana Murty
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
S. V. S. Narayana Murty has a total of 195 co-authors. Here are the top co-authors by number of shared publications:
- Boggarapu Nageswara Rao
KL Deemed to be University Department of Mechanical Engineering, Koneru Lakshmaiah Education Foundation Green Fields, Guntur
16 shared publications P. Ramesh Narayanan
Material Characterization Division, Vikram Sarabhai Space Center 1 , Thumba P.O., Trivandrum 695022
16 shared publicationsNiraj Nayan
14 shared publicationsS. C. Sharma
Vikram Sarabhai Space Centre, Trivandrum, India
10 shared publicationsS.C. Sharma
10 shared publicationsSushant K. Manwatkar
Material Characterisation Division, Materials and Metallurgy Group, Vikram Sarabhai Space Centre, Trivandrum, India
9 shared publications
Latest Publications
- Open Access
- 2 September 2026
- Published by Elsevier in SSRN Electronic Journal
Multiaxial Deformation Behavior and Yield Locus Evolution of Friction Stir Welded AA2219-T87 Aluminum Alloy: Microstructure–Property Correlations at Room and Elevated Temperatures
Friction stir welding (FSW) of AA2219-T87 aluminum alloy produces a mechanically heterogeneous joint comprising a nugget zone (NZ), a thermo-mechanically affected zone (TMAZ), and a heat-affected zone (HAZ), each with distinct microstructures and strengths. While uniaxial characterization of such joints is well established, their behavior under the multiaxial stress states typical of aerospace service remains largely unexplored. This study investigates the biaxial deformation and yield-locus evolution of FSW AA2219-T87 joints at room temperature and 150°C using a modified cruciform specimen that captures all weld zones within the gauge section. Miniature tensile tests revealed that the NZ was the weakest but most ductile zone, the HAZ was the strongest, and there was clear anisotropy between the weld and transverse directions. Digital image correlation showed that strain localization and fracture paths depended on both the biaxial load ratio and the softened TMAZ–HAZ interface, with equi-biaxial loading producing more distributed deformation than non-equibiaxial paths. Yield loci constructed from the biaxial data showed pronounced asymmetry and local non-convexity relative to the base alloy, indicating that conventional isotropic yield models cannot adequately describe the joint's response. At 150°C, yield loci contracted and became smoother, and EBSD (KAM, GAM, LAGB) and fractographic analyses confirmed a shift from strongly localized room-temperature deformation to more diffuse, recovery-assisted flow. These findings establish a direct link between weld-zone heterogeneity, temperature, and multiaxial deformation behavior, with implications for the structural design of friction-stir-welded aerospace aluminum components.
- 2 September 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessMultiaxial Deformation Behavior and Yield Locus Evolution of Friction Stir Welded AA2219-T87 Aluminum Alloy: Microstructure–Property Correlations at Room and Elevated Temperatures
Friction stir welding (FSW) of AA2219-T87 aluminum alloy produces a mechanically heterogeneous joint comprising a nugget zone (NZ), a thermo-mechanically affected zone (TMAZ), and a heat-affected zone (HAZ), each with distinct microstructures and strengths. While uniaxial characterization of such joints is well established, their behavior under the multiaxial stress states typical of aerospace service remains largely unexplored. This study investigates the biaxial deformation and yield-locus evolution of FSW AA2219-T87 joints at room temperature and 150°C using a modified cruciform specimen that captures all weld zones within the gauge section. Miniature tensile tests revealed that the NZ was the weakest but most ductile zone, the HAZ was the strongest, and there was clear anisotropy between the weld and transverse directions. Digital image correlation showed that strain localization and fracture paths depended on both the biaxial load ratio and the softened TMAZ–HAZ interface, with equi-biaxial loading producing more distributed deformation than non-equibiaxial paths. Yield loci constructed from the biaxial data showed pronounced asymmetry and local non-convexity relative to the base alloy, indicating that conventional isotropic yield models cannot adequately describe the joint's response. At 150°C, yield loci contracted and became smoother, and EBSD (KAM, GAM, LAGB) and fractographic analyses confirmed a shift from strongly localized room-temperature deformation to more diffuse, recovery-assisted flow. These findings establish a direct link between weld-zone heterogeneity, temperature, and multiaxial deformation behavior, with implications for the structural design of friction-stir-welded aerospace aluminum components.
- Open Access
- 1 April 2026
- Published by KEAI Publishing in Journal of Magnesium and Alloys
- Vol. 20
Realizing enhanced superplasticity in an AZ91 Mg alloy featuring layered heterogeneous microstructure and texture
- 1 April 2026
- Published by KEAI Publishing in Journal of Magnesium and Alloys
- Vol. 20
Open AccessRealizing enhanced superplasticity in an AZ91 Mg alloy featuring layered heterogeneous microstructure and texture
- Open Access
- 19 March 2026
- Published by Elsevier in SSRN Electronic Journal
Mechanical Stabilization of Austenite Induced by Cyclic Displacive Reversion in Maraging Steel
Maraging steel welds typically exhibit anomalous heat-affected-zone (HAZ) microstructures that cannot be explained by conventional elemental segregation-based arguments. These microstructural artefacts include dark bands and retained austenite across the HAZ, hardness gradients, and an uncommon residual stress profile. In this work, microstructural characterization and dilatometry reveal that the extremely high heating rates imposed during welding lead to displacive austenite reversion rather than diffusional reversion. The reverted austenite retains the dislocation structure of the parent martensite, and successive thermal cycles lead to a buildup of dislocation density. Since recovery proceeds unevenly across the weldment, this thermal cycling creates a softening-hardening asymmetry, resulting in certain regions having a substantially higher defect density than their surroundings. These defect-rich regions act as preferential sites for austenite stabilization during cooling and correspond to the retained-austenite pockets and the well-known dark-band morphology.To quantify these observations, a coupled thermo-metallo-mechanical numerical model was constructed by integrating dilatometry-derived transformation behavior with welding physics, such as transient heat flow and elasto-plastic stress evolution. The model captures (i) displacive reversion at high heating rates, (ii) defect inheritance and accumulation across cycles, and (iii) the resulting spatial variations in austenite stability and residual stresses. The simulations accurately reproduce the key microstructural features, including dark bands, the distribution of retained austenite, and the measured stress gradients.This work clarifies the origin of microstructural heterogeneity in welded maraging steels and provides a mechanistic basis for predicting defect-mediated phase stability under rapid thermal cycling.
- 19 March 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessMechanical Stabilization of Austenite Induced by Cyclic Displacive Reversion in Maraging Steel
Maraging steel welds typically exhibit anomalous heat-affected-zone (HAZ) microstructures that cannot be explained by conventional elemental segregation-based arguments. These microstructural artefacts include dark bands and retained austenite across the HAZ, hardness gradients, and an uncommon residual stress profile. In this work, microstructural characterization and dilatometry reveal that the extremely high heating rates imposed during welding lead to displacive austenite reversion rather than diffusional reversion. The reverted austenite retains the dislocation structure of the parent martensite, and successive thermal cycles lead to a buildup of dislocation density. Since recovery proceeds unevenly across the weldment, this thermal cycling creates a softening-hardening asymmetry, resulting in certain regions having a substantially higher defect density than their surroundings. These defect-rich regions act as preferential sites for austenite stabilization during cooling and correspond to the retained-austenite pockets and the well-known dark-band morphology.To quantify these observations, a coupled thermo-metallo-mechanical numerical model was constructed by integrating dilatometry-derived transformation behavior with welding physics, such as transient heat flow and elasto-plastic stress evolution. The model captures (i) displacive reversion at high heating rates, (ii) defect inheritance and accumulation across cycles, and (iii) the resulting spatial variations in austenite stability and residual stresses. The simulations accurately reproduce the key microstructural features, including dark bands, the distribution of retained austenite, and the measured stress gradients.This work clarifies the origin of microstructural heterogeneity in welded maraging steels and provides a mechanistic basis for predicting defect-mediated phase stability under rapid thermal cycling.
- 13 March 2026
- Published by Elsevier in Corrosion Science
- Vol. 264
Effect of aging time on the corrosion behaviour of selective laser melted (SLM) 15–5 PH stainless steel
- 13 March 2026
- Published by Elsevier in Corrosion Science
- Vol. 264
Effect of aging time on the corrosion behaviour of selective laser melted (SLM) 15–5 PH stainless steel
- Open Access
- 25 February 2026
- Published by Elsevier in SSRN Electronic Journal
Effect of temperature and strain rate on the hot-workability characteristics of as-cast XH55 (55Ni-17Cr-12Fe-9Mo-2Nb-1.5Al) superalloy: An approach using processing map and constitutive equation
In this study, the hot workability of the XH55 superalloy (55Ni-17Cr-12Fe-9Mo-2Nb-1.5Al) was studied in the as-cast condition through hot isothermal compression tests conducted over a temperature range of 850 to 1100°C and strain rates from 10-3 - 10 s-1. The alloy was produced by vacuum induction melting followed by vacuum arc remelting, resulting in the microstructure with dendritic features and M6C carbides. The deformation behaviour was analysed using true stress-strain responses, and a strain-dependent Arrhenius-type constitutive model was developed to predict the flow stress evolution. The model yielded an average activation energy of 583.97 kJ/mol, and its predictive capability was validated through close agreement between experimental and computed flow stresses. A processing map based on the Dynamic Materials Model was constructed to delineate stable and unstable deformation regime. Microstructural observations were correlated with the processing map to facilitate the identification of safe hot-working domains. The optimal deformation windows were determined to be 925 to 975°C at strain rates of 10-3 - 10-2.5 s-1 and 1010 to 1080°C at strain rates of 10-1.5 - 1 s-1, corresponding to processing conditions favorable for dynamic recrystallization through both continuous and discontinuous dynamic recrystallization mechanisms.
- 25 February 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessEffect of temperature and strain rate on the hot-workability characteristics of as-cast XH55 (55Ni-17Cr-12Fe-9Mo-2Nb-1.5Al) superalloy: An approach using processing map and constitutive equation
In this study, the hot workability of the XH55 superalloy (55Ni-17Cr-12Fe-9Mo-2Nb-1.5Al) was studied in the as-cast condition through hot isothermal compression tests conducted over a temperature range of 850 to 1100°C and strain rates from 10-3 - 10 s-1. The alloy was produced by vacuum induction melting followed by vacuum arc remelting, resulting in the microstructure with dendritic features and M6C carbides. The deformation behaviour was analysed using true stress-strain responses, and a strain-dependent Arrhenius-type constitutive model was developed to predict the flow stress evolution. The model yielded an average activation energy of 583.97 kJ/mol, and its predictive capability was validated through close agreement between experimental and computed flow stresses. A processing map based on the Dynamic Materials Model was constructed to delineate stable and unstable deformation regime. Microstructural observations were correlated with the processing map to facilitate the identification of safe hot-working domains. The optimal deformation windows were determined to be 925 to 975°C at strain rates of 10-3 - 10-2.5 s-1 and 1010 to 1080°C at strain rates of 10-1.5 - 1 s-1, corresponding to processing conditions favorable for dynamic recrystallization through both continuous and discontinuous dynamic recrystallization mechanisms.
- 28 January 2026
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 35 (22) , 22554-22563
Grain Boundary Controlled Superplasticity of FSP AZ91 Mg Alloy
- 28 January 2026
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 35 (22) , 22554-22563
Grain Boundary Controlled Superplasticity of FSP AZ91 Mg Alloy
- 27 October 2025
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 948
Early dynamic recrystallization and flow localization in an ultrafine-grained CrMoNbTiW refractory high entropy alloy
- 27 October 2025
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 948
Early dynamic recrystallization and flow localization in an ultrafine-grained CrMoNbTiW refractory high entropy alloy
- 28 February 2025
- Published by Elsevier in Acta Materialia
- Vol. 289
Austenite residual stress and lath martensite variant selection in low carbon steels
- 28 February 2025
- Published by Elsevier in Acta Materialia
- Vol. 289
Austenite residual stress and lath martensite variant selection in low carbon steels