Shuwei Yao
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Shuwei Yao has a total of 22 co-authors. Here are the top co-authors by number of shared publications:
Wensheng Liu
National Key Laboratory of Science and Technology on High-Strength Structural Materials, Central South University, Changsha, China
6 shared publications- Juan Wang
Institute for Advanced Study, Central South University, Changsha, China
5 shared publications - Yunzhu Ma
National Key Laboratory of Science and Technology on High-Strength Structural Materials, Central South University, Changsha, China
5 shared publications Yunzhu Ma
National Key Laboratory of Science and Technology on High-Strength Structural Materials, Central South University, Changsha, China
4 shared publicationsJuan Wang
Advanced Research Center, Central South University, Changsha, China
3 shared publicationsLingjiao Zhan
Advanced Research Center, Central South University, Changsha, China
3 shared publications
Latest Publications
- 23 October 2025
- Published by Springer Nature in Journal of Sol-Gel Science and Technology
- Vol. 116 (3) , 2822-2837
Carboxylate content as a key driver of phase transition and microstructure evolution in alumina-mullite fibers
- 23 October 2025
- Published by Springer Nature in Journal of Sol-Gel Science and Technology
- Vol. 116 (3) , 2822-2837
Carboxylate content as a key driver of phase transition and microstructure evolution in alumina-mullite fibers
- 7 May 2024
- Published by Springer Nature in Journal of Sol-Gel Science and Technology
- Vol. 110 (3) , 619-634
Effect of Y0.5Er0.5Ho0.5Yb0.5O3 addition on the microstructure and thermal stability of continuous alumina fibers
- 7 May 2024
- Published by Springer Nature in Journal of Sol-Gel Science and Technology
- Vol. 110 (3) , 619-634
Effect of Y0.5Er0.5Ho0.5Yb0.5O3 addition on the microstructure and thermal stability of continuous alumina fibers
- Open Access
- 11 January 2024
- Published by Springer Nature in Research Square
Effect of RE2O3 addition on the microstructure and thermal stability of continuous alumina fibers
Continuous alumina fibers with excellent thermal stability are essential in high-temperature applications. In this study, 0~1 wt% RE2O3 (RE = Y, Er, Yb, and Ho) were added to the alumina fibers to enhance thermal stability. The impact of RE2O3 addition on alumina fibers’ transformation and microstructure evolution of during the sintering process was systematically studied. The influence of single- and two-step sintering processes on the fiber microstructures was elucidated. The results suggested that adding RE2O3 impeded fiber densification, inhibited alumina grain growth, and enhanced the thermal stability of fibers. Using a two-step sintering process facilitated the achievement of fully dense alumina fibers with fine grains. The alumina fibers added with 1.0 wt% RE2O3 exhibited a remarkable strength retention rate of up to 93% after exposure to 1200 °C for 10 h. The TEM analysis revealed that RE elements segregation at α-Al2O3 grain boundaries due to their larger radius than the Al element contributed to stabilizing the microstructures of α-Al2O3 fibers at high service temperature.
- 11 January 2024
- Published by Springer Nature in Research Square
Open AccessEffect of RE2O3 addition on the microstructure and thermal stability of continuous alumina fibers
Continuous alumina fibers with excellent thermal stability are essential in high-temperature applications. In this study, 0~1 wt% RE2O3 (RE = Y, Er, Yb, and Ho) were added to the alumina fibers to enhance thermal stability. The impact of RE2O3 addition on alumina fibers’ transformation and microstructure evolution of during the sintering process was systematically studied. The influence of single- and two-step sintering processes on the fiber microstructures was elucidated. The results suggested that adding RE2O3 impeded fiber densification, inhibited alumina grain growth, and enhanced the thermal stability of fibers. Using a two-step sintering process facilitated the achievement of fully dense alumina fibers with fine grains. The alumina fibers added with 1.0 wt% RE2O3 exhibited a remarkable strength retention rate of up to 93% after exposure to 1200 °C for 10 h. The TEM analysis revealed that RE elements segregation at α-Al2O3 grain boundaries due to their larger radius than the Al element contributed to stabilizing the microstructures of α-Al2O3 fibers at high service temperature.
- 21 September 2023
- Published by Springer Nature in Journal of Sol-Gel Science and Technology
- Vol. 108 (3) , 609-620
Effect of the alumina and silica source mixing procedure on the microstructural evolution of alumina-mullite composite fibers prepared by sol–gel method
- 21 September 2023
- Published by Springer Nature in Journal of Sol-Gel Science and Technology
- Vol. 108 (3) , 609-620
Effect of the alumina and silica source mixing procedure on the microstructural evolution of alumina-mullite composite fibers prepared by sol–gel method
- Open Access
- 2 May 2023
- Published by Springer Nature in Research Square
Towards achieving ultrahigh thermal stability of fine-grained alumina fibers via segregation-induced ordered superstructures
High-strength materials often rely on their fine crystal structure, but the tendency of these crystals to coarsen at high temperatures poses a significant challenge in cutting-edge fields. Enhancing thermal stability while maintaining mechanical properties has become a complex issue in material development. In alumina ceramic fibers, we had observed that the ordered superstructures induced by segregation at the grain boundary networks of α-Al2O3 significantly enhanced the thermal stability of alumina grains without compromising their tensile strength. This led to a remarkable increase in heat-resistant temperature for fine alumina grains, which could exceed 1250 °C and thus greatly expanded the upper limit of alumina materials in high-temperature fields. Simultaneously, the phase-field simulation revealed that ordered superstructures likely reduced alumina's grain boundary diffusion coefficient to nearly match its volume diffusion coefficient. It was foreseeable that these structures would become a promising strategy for enhancing the high-temperature stability of alumina ceramic materials in the future.
- 2 May 2023
- Published by Springer Nature in Research Square
Open AccessTowards achieving ultrahigh thermal stability of fine-grained alumina fibers via segregation-induced ordered superstructures
High-strength materials often rely on their fine crystal structure, but the tendency of these crystals to coarsen at high temperatures poses a significant challenge in cutting-edge fields. Enhancing thermal stability while maintaining mechanical properties has become a complex issue in material development. In alumina ceramic fibers, we had observed that the ordered superstructures induced by segregation at the grain boundary networks of α-Al2O3 significantly enhanced the thermal stability of alumina grains without compromising their tensile strength. This led to a remarkable increase in heat-resistant temperature for fine alumina grains, which could exceed 1250 °C and thus greatly expanded the upper limit of alumina materials in high-temperature fields. Simultaneously, the phase-field simulation revealed that ordered superstructures likely reduced alumina's grain boundary diffusion coefficient to nearly match its volume diffusion coefficient. It was foreseeable that these structures would become a promising strategy for enhancing the high-temperature stability of alumina ceramic materials in the future.
- 11 May 2022
- Published by Springer Nature in Journal of Sol-Gel Science and Technology
- Vol. 103 (1) , 125-138
Preparation of a dense alumina fiber with nanograins by a novel two-step calcination
- 11 May 2022
- Published by Springer Nature in Journal of Sol-Gel Science and Technology
- Vol. 103 (1) , 125-138
Preparation of a dense alumina fiber with nanograins by a novel two-step calcination
- Open Access
Experimental and Molecular Dynamics Simulation Study on Sol–Gel Conversion Process of Aluminum Carboxylate System
Due to the lack of relevant in situ characterization techniques, the investigation of aluminum sol–gel progress is lacking. In this study, combined with molecular dynamics simulation and conventional experimental methods, the microstructures, rheological properties, and gelation process of the carboxylic aluminum sol system were studied. The experimental results showed that, with the increase in solid content, the microstructure of the colloid developed from a loose and porous framework to a homogeneous and compact structure. The viscosity of aluminum sol decreased significantly with the increase in temperature, and a temperature above 318 k was more conducive to improving the fluidity. The simulation results show that the increase in free volume and the connectivity of pores in colloidal framework structure were the key factors to improve fluidity. In addition, free water molecules had a higher migration rate, which could assist the rotation and rearrangement of macromolecular chains and also played an essential role in improving fluidity. The Molecular dynamics simulation (MD) results were consistent with experimental results and broaden the scope of experimental research, providing necessary theoretical guidance for enhancing the spinning properties of aluminum sol.
Open AccessExperimental and Molecular Dynamics Simulation Study on Sol–Gel Conversion Process of Aluminum Carboxylate System
Due to the lack of relevant in situ characterization techniques, the investigation of aluminum sol–gel progress is lacking. In this study, combined with molecular dynamics simulation and conventional experimental methods, the microstructures, rheological properties, and gelation process of the carboxylic aluminum sol system were studied. The experimental results showed that, with the increase in solid content, the microstructure of the colloid developed from a loose and porous framework to a homogeneous and compact structure. The viscosity of aluminum sol decreased significantly with the increase in temperature, and a temperature above 318 k was more conducive to improving the fluidity. The simulation results show that the increase in free volume and the connectivity of pores in colloidal framework structure were the key factors to improve fluidity. In addition, free water molecules had a higher migration rate, which could assist the rotation and rearrangement of macromolecular chains and also played an essential role in improving fluidity. The Molecular dynamics simulation (MD) results were consistent with experimental results and broaden the scope of experimental research, providing necessary theoretical guidance for enhancing the spinning properties of aluminum sol.
- 18 June 2021
- Published by Springer Nature in Journal of Sol-Gel Science and Technology
- Vol. 99 (1) , 169-177
Comparing the phase transformation of continuous alumina fiber and xerogels derived from the same precursor
- 18 June 2021
- Published by Springer Nature in Journal of Sol-Gel Science and Technology
- Vol. 99 (1) , 169-177
Comparing the phase transformation of continuous alumina fiber and xerogels derived from the same precursor
- Open Access
Preparation of Continuous Alumina Fiber with Nano Grains by the Addition of Iron Sol
Continuous alumina fiber exhibits excellent mechanical properties owing to its dense microstructure with fine grains. In this study, alumina fiber was prepared by the sol–gel method using iron sol as a nucleating agent. It was proposed that the α-Al2O3 grain size be adjusted based on the modification of colloidal particle size. The effect of holding temperature and reaction material ratio on the iron colloidal particle size was studied. The microstructure of alumina fiber was characterized by scanning electron microscopy (SEM). The experiment results indicated that iron colloidal particle size increases with the holding temperature and the NH4HCO3/Fe(NO3)3·9H2O ratio. The alumina fiber with uniform nano α-Al2O3 grains was obtained by calcination at 1400 °C for 5 min. The mean grain size tends to rise with the mean colloidal particle size. Using the iron sol as a nucleating agent, the fiber with a mean grain size of 22.5 nm could be formed. The tensile strength of fibers increased with the decrease of grain size.
Open AccessPreparation of Continuous Alumina Fiber with Nano Grains by the Addition of Iron Sol
Continuous alumina fiber exhibits excellent mechanical properties owing to its dense microstructure with fine grains. In this study, alumina fiber was prepared by the sol–gel method using iron sol as a nucleating agent. It was proposed that the α-Al2O3 grain size be adjusted based on the modification of colloidal particle size. The effect of holding temperature and reaction material ratio on the iron colloidal particle size was studied. The microstructure of alumina fiber was characterized by scanning electron microscopy (SEM). The experiment results indicated that iron colloidal particle size increases with the holding temperature and the NH4HCO3/Fe(NO3)3·9H2O ratio. The alumina fiber with uniform nano α-Al2O3 grains was obtained by calcination at 1400 °C for 5 min. The mean grain size tends to rise with the mean colloidal particle size. Using the iron sol as a nucleating agent, the fiber with a mean grain size of 22.5 nm could be formed. The tensile strength of fibers increased with the decrease of grain size.
- Open Access
- 18 October 2020
- Published by Springer Nature in Metallurgical and Materials Transactions A
- Vol. 51 (12) , 6546-6559
As-Built and Post-treated Microstructures of an Electron Beam Melting (EBM) Produced Nickel-Based Superalloy
The microstructures of an electron beam melted (EBM) nickel-based superalloy (Alloy 718) were comprehensively investigated in as-built and post-treated conditions, with particular focus individually on the contour (outer periphery) and hatch (core) regions of the build. The hatch region exhibited columnar grains with strong 〈001〉 texture in the build direction, while the contour region had a mix of columnar and equiaxed grains, with no preferred crystallographic texture. Both regions exhibited nearly identical hardness and carbide content. However, the contour region showed a higher number density of fine carbides compared to the hatch. The as-built material was subjected to two distinct post-treatments: (1) hot isostatic pressing (HIP) and (2) HIP plus heat treatment (HIP + HT), with the latter carried out as a single cycle inside the HIP vessel. Both post-treatments resulted in nearly an order of magnitude decrease in defect content in hatch and contour regions. HIP + HT led to grain coarsening in the contour, but did not alter the microstructure in the hatch region. Different factors that may be responsible for grain growth, such as grain size, grain orientation, grain boundary curvature and secondary phase particles, are discussed. The differences in carbide sizes in the hatch and contour regions appeared to decrease after post-treatment. After HIP + HT, similar higher hardness was observed in both the hatch and contour regions compared to the as-built material.
- 18 October 2020
- Published by Springer Nature in Metallurgical and Materials Transactions A
- Vol. 51 (12) , 6546-6559
Open AccessAs-Built and Post-treated Microstructures of an Electron Beam Melting (EBM) Produced Nickel-Based Superalloy
The microstructures of an electron beam melted (EBM) nickel-based superalloy (Alloy 718) were comprehensively investigated in as-built and post-treated conditions, with particular focus individually on the contour (outer periphery) and hatch (core) regions of the build. The hatch region exhibited columnar grains with strong 〈001〉 texture in the build direction, while the contour region had a mix of columnar and equiaxed grains, with no preferred crystallographic texture. Both regions exhibited nearly identical hardness and carbide content. However, the contour region showed a higher number density of fine carbides compared to the hatch. The as-built material was subjected to two distinct post-treatments: (1) hot isostatic pressing (HIP) and (2) HIP plus heat treatment (HIP + HT), with the latter carried out as a single cycle inside the HIP vessel. Both post-treatments resulted in nearly an order of magnitude decrease in defect content in hatch and contour regions. HIP + HT led to grain coarsening in the contour, but did not alter the microstructure in the hatch region. Different factors that may be responsible for grain growth, such as grain size, grain orientation, grain boundary curvature and secondary phase particles, are discussed. The differences in carbide sizes in the hatch and contour regions appeared to decrease after post-treatment. After HIP + HT, similar higher hardness was observed in both the hatch and contour regions compared to the as-built material.