Biswanath Doloi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Biswanath Doloi has a total of 28 co-authors. Here are the top co-authors by number of shared publications:
- Bijoy Bhattacharyya
Production Engineering Department, Jadavpur University, Kolkata, India
17 shared publications - Biplab Ranjan Sarkar
Department of Production Engineering, Faculty of Engineering & Technology, Jadavpur University, Kolkata 700032, West Bengal, India
9 shared publications - Golam Kibria
Department of Mechanical Engineering, Aliah University, Kolkata, India
7 shared publications - Santosh Kumar
Production Engineering Department, Jadavpur University, Kolkata, India
7 shared publications B. Bhattacharyya
Production Engineering Department, Jadavpur University, Kolkata 700032, India
6 shared publications- Biplab Bhattacharyya
Jadavpur University, Kolkata, India
6 shared publications
Latest Publications
- 19 March 2025
- Published by Springer Nature in Sādhanā
- Vol. 50 (2) , 1-15
Parametric analysis of poly methyl methacrylate (PMMA) laser marking using fiber laser
- 19 March 2025
- Published by Springer Nature in Sādhanā
- Vol. 50 (2) , 1-15
Parametric analysis of poly methyl methacrylate (PMMA) laser marking using fiber laser
- 27 September 2024
- Published by World Scientific Pub Co Pte Ltd in Journal of Advanced Manufacturing Systems
- Vol. 24 (02) , 283-308
Experimentation into Electrochemical Discharge Milling for the Generation of Cavity on Glass
The development of electrochemical discharge machining (ECDM) and the use of electrically nonconducting materials in microelectromechanical systems (MEMS), biomedical applications and making lab-on-a-chip devices are increasing tremendously. In this study, the performance of electrochemical discharge milling was improved by introducing the bottom-up movement of tool-electrode, i.e. vertically upward tool-feeding technique. The development of gas film model was compared with the actual gas film shapes to find out the problems associated with the existing tool-feeding technique and the advantages of vertically upward tool-feeding technique. Single channels were generated on the soda lime glass workpiece to analyze and obtain appropriate process parameters for good-quality channels. Applied voltage, electrolyte concentration and tool feed rate (TFR) were varied to get good-quality channel. It was achieved at the process parameters of an applied voltage of 40 V, an electrolyte concentration of 5 M and a TFR of 50 [ ]m/s. With this parametric setting, four consecutive parallel channels were generated to get cavity on the soda lime glass. Rectangular-shaped cavities were fabricated by adopting three different strategies to minimize the problem of material deposition along the border of two adjacent parallel channels. These rectangular cavities were observed under a microscope to measure and obtain the surface topography which revealed the usability of third strategy of generating smooth and uniform cavity with lower surface roughness ([ ][ ]). A rectangular cavity of 0.247-[ ]m surface roughness with smooth corners and edges was obtained at 40 V of applied voltage and 50 [ ]m/s of TFR.
- 27 September 2024
- Published by World Scientific Pub Co Pte Ltd in Journal of Advanced Manufacturing Systems
- Vol. 24 (02) , 283-308
Experimentation into Electrochemical Discharge Milling for the Generation of Cavity on Glass
The development of electrochemical discharge machining (ECDM) and the use of electrically nonconducting materials in microelectromechanical systems (MEMS), biomedical applications and making lab-on-a-chip devices are increasing tremendously. In this study, the performance of electrochemical discharge milling was improved by introducing the bottom-up movement of tool-electrode, i.e. vertically upward tool-feeding technique. The development of gas film model was compared with the actual gas film shapes to find out the problems associated with the existing tool-feeding technique and the advantages of vertically upward tool-feeding technique. Single channels were generated on the soda lime glass workpiece to analyze and obtain appropriate process parameters for good-quality channels. Applied voltage, electrolyte concentration and tool feed rate (TFR) were varied to get good-quality channel. It was achieved at the process parameters of an applied voltage of 40 V, an electrolyte concentration of 5 M and a TFR of 50 [ ]m/s. With this parametric setting, four consecutive parallel channels were generated to get cavity on the soda lime glass. Rectangular-shaped cavities were fabricated by adopting three different strategies to minimize the problem of material deposition along the border of two adjacent parallel channels. These rectangular cavities were observed under a microscope to measure and obtain the surface topography which revealed the usability of third strategy of generating smooth and uniform cavity with lower surface roughness ([ ][ ]). A rectangular cavity of 0.247-[ ]m surface roughness with smooth corners and edges was obtained at 40 V of applied voltage and 50 [ ]m/s of TFR.
- 23 March 2024
- Published by World Scientific Pub Co Pte Ltd in Surface Review and Letters
- Vol. 31 (11)
MICRO-EDD OF INCONEL 800 USING ELECTROMAGNETIC FIELD
Micro-electro-discharge drilling ([ ]EDD) is a type of non-traditional machining process used for drilling micro-holes of desired dimensions with a high aspect ratio. But, there are no such research works that could have explained the desired accurate circular shape of micro-holes. The need for a more advanced hybrid machining process to improve the overall efficiency in terms of mainly desired circular shape and radial overcut is evolved. In this research work, an electromagnetic field force-assisted micro-EDM process has been carried out on Inconel 800 with a copper tool of 450[ ][ ]m. Experimental results showed that measured metal removal rate and tool wear rate decreased for ascending values of magnetic flux density, peak current and gap voltage, whereas circularity increases linearly with an increase in magnetic flux density and also the effects of magnetic field on circularity of micro-holes on Inconel 800 are more predominant than other parameters.
- 23 March 2024
- Published by World Scientific Pub Co Pte Ltd in Surface Review and Letters
- Vol. 31 (11)
MICRO-EDD OF INCONEL 800 USING ELECTROMAGNETIC FIELD
Micro-electro-discharge drilling ([ ]EDD) is a type of non-traditional machining process used for drilling micro-holes of desired dimensions with a high aspect ratio. But, there are no such research works that could have explained the desired accurate circular shape of micro-holes. The need for a more advanced hybrid machining process to improve the overall efficiency in terms of mainly desired circular shape and radial overcut is evolved. In this research work, an electromagnetic field force-assisted micro-EDM process has been carried out on Inconel 800 with a copper tool of 450[ ][ ]m. Experimental results showed that measured metal removal rate and tool wear rate decreased for ascending values of magnetic flux density, peak current and gap voltage, whereas circularity increases linearly with an increase in magnetic flux density and also the effects of magnetic field on circularity of micro-holes on Inconel 800 are more predominant than other parameters.
- 22 February 2024
- Published by Springer Nature in Sādhanā
- Vol. 49 (1) , 1-10
Experimental investigation into ultrasonic micro machining for fabrication of micro channels on Quartz
- 22 February 2024
- Published by Springer Nature in Sādhanā
- Vol. 49 (1) , 1-10
Experimental investigation into ultrasonic micro machining for fabrication of micro channels on Quartz
- 1 September 2023
- Published by ASME International in Journal of Micro and Nano-Manufacturing
- Vol. 11 (3) , 1-59
Micro-Channel Cutting on Glass in Electrochemical Discharge Machining Process Using Different Electrolytes and Tool Polarity
Microchannel cutting on electrically nonconducting materials with electrochemical discharge machining (ECDM) process has drawn a momentous attention in manufacturing field as compared to other existing nontraditional machining processes. In the present research work, an effort has been accomplished to investigate the effects of process parameters, namely, applied voltage (V), electrolyte concentrations(wt%), pulse frequency, and duty ratio on different performance characteristics of ECDM viz., material removal rate (MRR), overcut (OC) and heat-affected zone (HAZ) area during microchannel cutting on glass. Also, the comparative performance studies during microchannel cutting have been done by using mixed electrolyte of NaOH and KOH and different tool polarities. Overcut is measured as lower (42.26 μm) when aqueous KOH electrolyte is used and as higher (133.44 μm) for aqueous NaOH electrolyte. HAZ enlarges with enrichment in concentration for both types of electrolyte. It is observed that polarity has a vital role on various machining characteristics. As compared to direct polarity, MRR is found very low (3.2 mg/h) in reverse polarity of tool. Overcut is found low in KOH electrolyte for both types of tool polarity (i.e., 64.68 μm for direct polarity and 42.27 μm for reverse polarity). The process parameters influence on the surface texture of microchannels. Microcrack is noticed for direct polarity of tool.
- 1 September 2023
- Published by ASME International in Journal of Micro and Nano-Manufacturing
- Vol. 11 (3) , 1-59
Micro-Channel Cutting on Glass in Electrochemical Discharge Machining Process Using Different Electrolytes and Tool Polarity
Microchannel cutting on electrically nonconducting materials with electrochemical discharge machining (ECDM) process has drawn a momentous attention in manufacturing field as compared to other existing nontraditional machining processes. In the present research work, an effort has been accomplished to investigate the effects of process parameters, namely, applied voltage (V), electrolyte concentrations(wt%), pulse frequency, and duty ratio on different performance characteristics of ECDM viz., material removal rate (MRR), overcut (OC) and heat-affected zone (HAZ) area during microchannel cutting on glass. Also, the comparative performance studies during microchannel cutting have been done by using mixed electrolyte of NaOH and KOH and different tool polarities. Overcut is measured as lower (42.26 μm) when aqueous KOH electrolyte is used and as higher (133.44 μm) for aqueous NaOH electrolyte. HAZ enlarges with enrichment in concentration for both types of electrolyte. It is observed that polarity has a vital role on various machining characteristics. As compared to direct polarity, MRR is found very low (3.2 mg/h) in reverse polarity of tool. Overcut is found low in KOH electrolyte for both types of tool polarity (i.e., 64.68 μm for direct polarity and 42.27 μm for reverse polarity). The process parameters influence on the surface texture of microchannels. Microcrack is noticed for direct polarity of tool.
- Open Access
- 1 June 2023
- Published by Central Manufacturing Technology Institute in Manufacturing Technology Today (MTT)
- Vol. 22 (6) , 61-67
Experimental investigation into fiber laser marking on titanium alloy (Ti6AL4V)
The paper deals with the analysis of marking quality on Ti6Al4V by using thermal energy of laser beam. The variation of process variables such as laser irradiation, pulse rate, scan rate, duty cycle and transverse feed resulted in the generation of colours on the surface which have a considerable marking contrast value. The intensity analysis conducted on line marking and surface marking reveals the fact that variables like laser irradiation, transverse feed, and scan rate plays a significant role in the change of colours when other process variables are held constant. Experimental studies revealed that the highest mark intensity obtained was 0.70 (pinkish colour) where lowest value obtained was 0.10 (purple colour whereas the standard maximum and minimum mark intensity were 1 (white) and 0 (black).
- 1 June 2023
- Published by Central Manufacturing Technology Institute in Manufacturing Technology Today (MTT)
- Vol. 22 (6) , 61-67
Open AccessExperimental investigation into fiber laser marking on titanium alloy (Ti6AL4V)
The paper deals with the analysis of marking quality on Ti6Al4V by using thermal energy of laser beam. The variation of process variables such as laser irradiation, pulse rate, scan rate, duty cycle and transverse feed resulted in the generation of colours on the surface which have a considerable marking contrast value. The intensity analysis conducted on line marking and surface marking reveals the fact that variables like laser irradiation, transverse feed, and scan rate plays a significant role in the change of colours when other process variables are held constant. Experimental studies revealed that the highest mark intensity obtained was 0.70 (pinkish colour) where lowest value obtained was 0.10 (purple colour whereas the standard maximum and minimum mark intensity were 1 (white) and 0 (black).
- Open Access
- 1 June 2023
- Published by Central Manufacturing Technology Institute in Manufacturing Technology Today (MTT)
- Vol. 22 (6) , 14-19
Experimental Investigation into micro-ultrasonic machining of zirconia using multiple tips micro-tool
The usage of micro products has grown significantly over the past ten years in a variety of industries, including engineering, automotive, health care, and electronics. Materials that are hard and brittle is frequently used to make microproducts like microreactors, microfluidic devices etc. Micro ultrasonic machining (µ-USM) is most excellent micro machining process to produce micro features on ceramic materials. The multiple tips micro-tool has been fabricated to generate multiple micro-channel on zirconia by µ-USM process. The effect of process parameters such as power rating, abrasive slurry concentration, tool feed rate and slurry flow rate on width overcut and material removal rate (MRR) of micro channels generated on zirconia were investigated. By using multiple tips micro-tool, micro-channels were produced using µ-USM which increases productivity of µ-USM. The higher value of MRR and lower width overcut achieved as 3.970mm3 /min and 26µm respectively during multiple micro channel fabrication.
- 1 June 2023
- Published by Central Manufacturing Technology Institute in Manufacturing Technology Today (MTT)
- Vol. 22 (6) , 14-19
Open AccessExperimental Investigation into micro-ultrasonic machining of zirconia using multiple tips micro-tool
The usage of micro products has grown significantly over the past ten years in a variety of industries, including engineering, automotive, health care, and electronics. Materials that are hard and brittle is frequently used to make microproducts like microreactors, microfluidic devices etc. Micro ultrasonic machining (µ-USM) is most excellent micro machining process to produce micro features on ceramic materials. The multiple tips micro-tool has been fabricated to generate multiple micro-channel on zirconia by µ-USM process. The effect of process parameters such as power rating, abrasive slurry concentration, tool feed rate and slurry flow rate on width overcut and material removal rate (MRR) of micro channels generated on zirconia were investigated. By using multiple tips micro-tool, micro-channels were produced using µ-USM which increases productivity of µ-USM. The higher value of MRR and lower width overcut achieved as 3.970mm3 /min and 26µm respectively during multiple micro channel fabrication.
- Open Access
- 1 May 2023
- Published by Central Manufacturing Technology Institute in Manufacturing Technology Today (MTT)
- Vol. 22 (5) , 18-23
On electrochemical discharge milling of glass with horizontal tool and vertically upward feeding technique
Electrochemical Discharge Milling (ECD milling) process encounters some problems like the uneven edge of the machined channel, lower machining depth, uncontrollable spark discharge, etc. The primary cause of those issues is a lack of gas bubbles in the machining area, which are necessary for good spark discharges. Due to the buoyancy of the liquid, gas bubbles cannot remain at the tool-electrode tip and poor flushing arises from feeding the tool-electrode on the top surface of the workpiece. In this study, horizontal tool-electrode and vertically upward feeding technique has been introduced to solve the problems that arise during the existing feeding technique. The material removal rate (MRR) and overcut during ECD milling are observed and analysed by changing the applied voltage, concentration of electrolyte and feed rate of tool. MRR and overcut are found as 5.025µg/min and 116.86µm respectively at 40V, 20wt% concentration of electrolyte and 50µm/sec of feed rate.
- 1 May 2023
- Published by Central Manufacturing Technology Institute in Manufacturing Technology Today (MTT)
- Vol. 22 (5) , 18-23
Open AccessOn electrochemical discharge milling of glass with horizontal tool and vertically upward feeding technique
Electrochemical Discharge Milling (ECD milling) process encounters some problems like the uneven edge of the machined channel, lower machining depth, uncontrollable spark discharge, etc. The primary cause of those issues is a lack of gas bubbles in the machining area, which are necessary for good spark discharges. Due to the buoyancy of the liquid, gas bubbles cannot remain at the tool-electrode tip and poor flushing arises from feeding the tool-electrode on the top surface of the workpiece. In this study, horizontal tool-electrode and vertically upward feeding technique has been introduced to solve the problems that arise during the existing feeding technique. The material removal rate (MRR) and overcut during ECD milling are observed and analysed by changing the applied voltage, concentration of electrolyte and feed rate of tool. MRR and overcut are found as 5.025µg/min and 116.86µm respectively at 40V, 20wt% concentration of electrolyte and 50µm/sec of feed rate.
- 15 December 2022
- Published by Springer Nature
- p. 173-184
Experimental Studies on Laser Marking Characteristics of Stainless Steel 304
- 15 December 2022
- Published by Springer Nature
- p. 173-184
Experimental Studies on Laser Marking Characteristics of Stainless Steel 304
- 4 October 2022
- Published by Springer Nature
- p. 173-187
Advancement of Electrochemical Discharge Machining Process—A Review
- 4 October 2022
- Published by Springer Nature
- p. 173-187
Advancement of Electrochemical Discharge Machining Process—A Review