Lei Shi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Lei Shi has a total of 80 co-authors. Here are the top co-authors by number of shared publications:
Kangyao Deng
College of Mechanical and Power Engineering, Shanghai Jiao Tong University, China
13 shared publicationsJianghua Cheng
4 shared publicationsLing Leng
School of Mechanical Engineering, Shanghai Jiao Tong University, Shanghai, China
4 shared publicationsKangbo Lu
3 shared publicationsZiqiang Chen
3 shared publicationsCiwei Qin
2 shared publications
Latest Publications
- 6 February 2026
- Published by SAGE Publications in International Journal of Engine Research
- Vol. 27 (9) , 1496-1515
A review of model-based offline and online optimization control systems for combustion engines
To meet the development requirements of ultra-high efficiency, ultra-low emissions, and strong working condition adaptability for internal combustion engines, the collaborative optimization of engine performance and emissions has become an urgent problem to be solved. Nevertheless, several performance indicators of engines are mutually restricted, and there is a complex coupling relationship between controllable variables and performance parameters. All these make it difficult to rely on experience to achieve the multi-objective performance optimization for engines, promoting the research on model-based multi-objective engine performance optimization. Since the effectiveness of optimization relies on fast and accurate predictive models, the advantages of machine learning (ML) algorithms have been fully exploited. In this paper, the literature on engine performance prediction models based on ML algorithms is reviewed. Moreover, the technical fields and significant achievements with regard to multi-objective engine performance optimization based on intelligent optimization algorithms are analyzed and summarized. The most commonly used intelligent algorithms in engine performance optimization are evaluated and compared in detail, which provides guidance for the analysis and selection of proper optimization strategies, modeling methods, and optimization algorithms. Finally, this paper discusses the research hotspots and future development direction in this field, in order to provide more ideas for the future research on engine multi-objective performance optimization.
- 6 February 2026
- Published by SAGE Publications in International Journal of Engine Research
- Vol. 27 (9) , 1496-1515
A review of model-based offline and online optimization control systems for combustion engines
To meet the development requirements of ultra-high efficiency, ultra-low emissions, and strong working condition adaptability for internal combustion engines, the collaborative optimization of engine performance and emissions has become an urgent problem to be solved. Nevertheless, several performance indicators of engines are mutually restricted, and there is a complex coupling relationship between controllable variables and performance parameters. All these make it difficult to rely on experience to achieve the multi-objective performance optimization for engines, promoting the research on model-based multi-objective engine performance optimization. Since the effectiveness of optimization relies on fast and accurate predictive models, the advantages of machine learning (ML) algorithms have been fully exploited. In this paper, the literature on engine performance prediction models based on ML algorithms is reviewed. Moreover, the technical fields and significant achievements with regard to multi-objective engine performance optimization based on intelligent optimization algorithms are analyzed and summarized. The most commonly used intelligent algorithms in engine performance optimization are evaluated and compared in detail, which provides guidance for the analysis and selection of proper optimization strategies, modeling methods, and optimization algorithms. Finally, this paper discusses the research hotspots and future development direction in this field, in order to provide more ideas for the future research on engine multi-objective performance optimization.
- 13 December 2025
- Published by Elsevier in Journal of Power Sources
- Vol. 665
Amorphous NiS deposited on crystalline Co3O4 nanosheets boosting electron transfer for efficient hydrogen evolution
- 13 December 2025
- Published by Elsevier in Journal of Power Sources
- Vol. 665
Amorphous NiS deposited on crystalline Co3O4 nanosheets boosting electron transfer for efficient hydrogen evolution
- Open Access
- 1 January 2025
- Published by Tech Science Press in Fluid Dynamics & Materials Processing
- Vol. 21 (2) , 405-426
Effects of Fuel Injection and Ignition on the Direct-Start Process of a Gasoline Direct Injection (GDI) Engine
During the highly transient process of the direct-start in a four-cylinder GDI engine, each cylinder exhibits specific characteristics in terms of in-cylinder conditions and energy demands, necessitating different control for each cylinder. However, recent studies have paid insufficient attention to cylinders other than the first starting cylinder. This paper proposes a comprehensive control strategy based on experimental data from the direct-start process of the second, third, and fourth cylinders, aiming to enhance the characteristics of combustion and emission performance through the optimization of injection timing, equivalence ratio, and ignition timing. The research findings indicate that the second cylinder should inject fuel approximately 10 ms after the first cylinder ignites to mix thoroughly the fuel with air. The ignition timing of the second cylinder should be close to the highest point of the piston movement to minimize hindrance to the piston compression process. The third and fourth cylinders should adopt a delayed injection timing strategy to prevent the escape of injected fuel caused by low engine speed. The optimal ignition timing for the third cylinder is 20°CA BTDC, while the fourth cylinder should be ignited earlier due to its stronger airflow and faster formation of a mixture that can be ignited. As the fuel injection quantity increases, the power output of the three cylinders enhances, but at the same time, emissions also increase. Therefore, their optimal equivalence ratios are determined as 1.2, 1.4, and 1.2, respectively, striking a balance between combustion and emission performances.
- 1 January 2025
- Published by Tech Science Press in Fluid Dynamics & Materials Processing
- Vol. 21 (2) , 405-426
Open AccessEffects of Fuel Injection and Ignition on the Direct-Start Process of a Gasoline Direct Injection (GDI) Engine
During the highly transient process of the direct-start in a four-cylinder GDI engine, each cylinder exhibits specific characteristics in terms of in-cylinder conditions and energy demands, necessitating different control for each cylinder. However, recent studies have paid insufficient attention to cylinders other than the first starting cylinder. This paper proposes a comprehensive control strategy based on experimental data from the direct-start process of the second, third, and fourth cylinders, aiming to enhance the characteristics of combustion and emission performance through the optimization of injection timing, equivalence ratio, and ignition timing. The research findings indicate that the second cylinder should inject fuel approximately 10 ms after the first cylinder ignites to mix thoroughly the fuel with air. The ignition timing of the second cylinder should be close to the highest point of the piston movement to minimize hindrance to the piston compression process. The third and fourth cylinders should adopt a delayed injection timing strategy to prevent the escape of injected fuel caused by low engine speed. The optimal ignition timing for the third cylinder is 20°CA BTDC, while the fourth cylinder should be ignited earlier due to its stronger airflow and faster formation of a mixture that can be ignited. As the fuel injection quantity increases, the power output of the three cylinders enhances, but at the same time, emissions also increase. Therefore, their optimal equivalence ratios are determined as 1.2, 1.4, and 1.2, respectively, striking a balance between combustion and emission performances.
- 29 November 2024
- Published by Elsevier in ISA Transactions
- Vol. 157, 107-123
Smooth and safe stop: Fixed-time fault tolerant control for heavy legged robot with active identification on tolerance capability
- 29 November 2024
- Published by Elsevier in ISA Transactions
- Vol. 157, 107-123
Smooth and safe stop: Fixed-time fault tolerant control for heavy legged robot with active identification on tolerance capability