İbrahim Uyanık
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
İbrahim Uyanık has a total of 18 co-authors. Here are the top co-authors by number of shared publications:
Adem Yurtsever
2 shared publications- Emine Busra Colakoglu
Graduate School of Natural and Applied Sciences, Environmental Engineering Department, Erciyes University , Kayseri
2 shared publications - Hamdi Mıhçıokur
Engineering Faculty, Environmental Engineering Department, Erciyes University , Kayseri
2 shared publications - Oktay Özkan
Department of Environmental Engineering, Erciyes University, Kayseri, Turkey
2 shared publications - Zeynep İpek
Ankara Su ve Kanalizasyon İdaresi
2 shared publications - Adem Yurtsever
Department of Environmental Engineering Faculty of Engineering İstanbul University‐Cerrahpaşa Istanbul Türkiye
1 shared publication
Latest Publications
- 15 March 2026
- Published by Black Sea Journal of Engineering and Science in Black Sea Journal of Engineering and Science
- Vol. 9 (2) , 928-933
Sustainable Management of Industrial Wastewater in Türkiye: Pilot-Scale Gravity-Driven Dynamic Membranes for Water Reuse
There is an urgent need to transition toward a circular economy in Türkiye by improving effluent quality for industrial water reuse. This study evaluates the management and performance of a sustainable, pilot-scale (170 L) gravity-driven dynamic membrane (GD-DM) system designed for low-energy wastewater reclamation. Unlike conventional high-pressure membrane systems that suffer from high energy demands and chemical cleaning requirements, this GD-DM system integrate a 150 µm stainless steel support material to obtain a very low turbidity water. To align with waste-to-resource principles, the dynamic membrane layer was formed using waste activated sludge from the return line of an organized industrial wastewater treatment plant, eliminating the need for synthetic filtration media. Operating with automated sensors for real-time turbidity and flow monitoring, the system achieved an average flux of 353 L/m².h. High-quality reclaimed water (turbidity < 5 NTU) was consistently produced within 3 minutes, with levels dropping below 1 NTU for over 84% of the operational cycle. Because the conductivity of the permeate is very high (above 4,301 µS/cm), it cannot be reused for agricultural purposes. This approach provides a microfiltration-level effluent quality while maintaining a flux 20–30 times higher than traditional polymeric membranes. The treated water is virtually suspended-solids-free, making it suitable for industrial reuse. By drastically reducing energy consumption and operational complexity, the GD-DM system offers a scalable and environmentally sustainable solution for managing industrial wastewater and protecting receiving environments from pollutants like microplastics.
- 15 March 2026
- Published by Black Sea Journal of Engineering and Science in Black Sea Journal of Engineering and Science
- Vol. 9 (2) , 928-933
Sustainable Management of Industrial Wastewater in Türkiye: Pilot-Scale Gravity-Driven Dynamic Membranes for Water Reuse
There is an urgent need to transition toward a circular economy in Türkiye by improving effluent quality for industrial water reuse. This study evaluates the management and performance of a sustainable, pilot-scale (170 L) gravity-driven dynamic membrane (GD-DM) system designed for low-energy wastewater reclamation. Unlike conventional high-pressure membrane systems that suffer from high energy demands and chemical cleaning requirements, this GD-DM system integrate a 150 µm stainless steel support material to obtain a very low turbidity water. To align with waste-to-resource principles, the dynamic membrane layer was formed using waste activated sludge from the return line of an organized industrial wastewater treatment plant, eliminating the need for synthetic filtration media. Operating with automated sensors for real-time turbidity and flow monitoring, the system achieved an average flux of 353 L/m².h. High-quality reclaimed water (turbidity < 5 NTU) was consistently produced within 3 minutes, with levels dropping below 1 NTU for over 84% of the operational cycle. Because the conductivity of the permeate is very high (above 4,301 µS/cm), it cannot be reused for agricultural purposes. This approach provides a microfiltration-level effluent quality while maintaining a flux 20–30 times higher than traditional polymeric membranes. The treated water is virtually suspended-solids-free, making it suitable for industrial reuse. By drastically reducing energy consumption and operational complexity, the GD-DM system offers a scalable and environmentally sustainable solution for managing industrial wastewater and protecting receiving environments from pollutants like microplastics.
- 14 February 2026
- Published by Oxford University Press (OUP) in Integrated Environmental Assessment and Management
- Vol. 22 (4) , 1297-1308
Microplastics in an industrial zone wastewater treatment plant: Characterization, fate, and risk assessment
The majority of research on microplastic (MP) characterization and removal has focused on municipal wastewater treatment plants (WWTPs). Hence, this study was performed at an industrial zone WWTP with sectors of textile, plastic recycling, furniture, etc. Three monthly sampling campaigns were conducted to analyze the MPs (abundance, shape, color, size, polymer type) and to investigate their fate and removal rate in the WWTP. Furthermore, the environmental risk assessment using EPI Suite modeling was conducted for common MP polymer types. The results indicated that the highest MP concentration was detected in the sludge sample (3,734 MP/L), whereas the lowest one was observed in the effluent sample (52 MP/L). Whereas large MPs (5 mm to 425 µm) were removed by primary treatment processes, smaller MPs (250 to 125 µm) showed a tendency for accumulation in the sludge. The most dominant MP shapes were fiber and fragment in both wastewater and sludge samples, whereas the most dominant polymer types were polypropylene (38%), polyethylene (24%), and polyethylene terephthalate (11%). The environmental risk assessment reveals that polyvinyl chloride, polyethylene terephthalate, and polystyrene, present in minimal quantities in this study, are more likely to impact the growth of living organisms significantly compared to more common polymer types like polypropylene and polyethylene. Although the overall MP removal efficiency of the industrial zone WWTP was 88%, a significant quantity of MPs (1.5 × 109 MP/day) was still discharged into the Kızılırmak river that is used mostly for irrigation. Effective control/reduction of MP discharge necessitates the implementation of tertiary treatment processes in industrial zone WWTPs to prevent soil pollution.
- 14 February 2026
- Published by Oxford University Press (OUP) in Integrated Environmental Assessment and Management
- Vol. 22 (4) , 1297-1308
Microplastics in an industrial zone wastewater treatment plant: Characterization, fate, and risk assessment
The majority of research on microplastic (MP) characterization and removal has focused on municipal wastewater treatment plants (WWTPs). Hence, this study was performed at an industrial zone WWTP with sectors of textile, plastic recycling, furniture, etc. Three monthly sampling campaigns were conducted to analyze the MPs (abundance, shape, color, size, polymer type) and to investigate their fate and removal rate in the WWTP. Furthermore, the environmental risk assessment using EPI Suite modeling was conducted for common MP polymer types. The results indicated that the highest MP concentration was detected in the sludge sample (3,734 MP/L), whereas the lowest one was observed in the effluent sample (52 MP/L). Whereas large MPs (5 mm to 425 µm) were removed by primary treatment processes, smaller MPs (250 to 125 µm) showed a tendency for accumulation in the sludge. The most dominant MP shapes were fiber and fragment in both wastewater and sludge samples, whereas the most dominant polymer types were polypropylene (38%), polyethylene (24%), and polyethylene terephthalate (11%). The environmental risk assessment reveals that polyvinyl chloride, polyethylene terephthalate, and polystyrene, present in minimal quantities in this study, are more likely to impact the growth of living organisms significantly compared to more common polymer types like polypropylene and polyethylene. Although the overall MP removal efficiency of the industrial zone WWTP was 88%, a significant quantity of MPs (1.5 × 109 MP/day) was still discharged into the Kızılırmak river that is used mostly for irrigation. Effective control/reduction of MP discharge necessitates the implementation of tertiary treatment processes in industrial zone WWTPs to prevent soil pollution.
- Open Access
- 1 January 2026
- Published by Kare Publishing in Journal of Clinical Practice and Research
- Vol. 48 (1) , 1-8
The Impact of Microplastics on Human Health: An Urgent Public Health Concern
Microplastics (MPs) have rapidly become one of the most pervasive pollutants in the modern world. Far from being confined to oceans or waste sites, these tiny particles now circulate through the air we breathe, the water we drink, and the food we eat. As everyday plastic items break down over time, they form microscopic fragments that can travel long distances and enter the human body through inhalation or ingestion. Once inside the body, these particles may accumulate in organs and interact with biological systems in ways that scientists are only beginning to understand. This review synthesizes current scientific findings on the formation of MPs, their pathways into and persistence within the human body, and their potential health impacts. Although there is no standardized method for measuring MPs, the main analytical techniques used for biological samples are discussed. Furthermore, the toxicity and environmental impacts of plastic types to which humans are exposed are assessed using the EPI Suite™ program developed by the U.S. Environmental Protection Agency (USEPA). Certain MP types, such as polyethylene and polypropylene, appear more toxic due to their low biodegradability. Although evidence increasingly identifies MPs as a growing public health concern, many questions remain unanswered. Health effects related to gastrointestinal and respiratory health systems are examined, while long‑term effects, behavior in human tissues, and associations with chronic diseases—including potential links to cancer—require further multidisciplinary investigation. As global plastic use continues to rise, understanding and mitigating MP exposure will be essential for protecting human health.
- 1 January 2026
- Published by Kare Publishing in Journal of Clinical Practice and Research
- Vol. 48 (1) , 1-8
Open AccessThe Impact of Microplastics on Human Health: An Urgent Public Health Concern
Microplastics (MPs) have rapidly become one of the most pervasive pollutants in the modern world. Far from being confined to oceans or waste sites, these tiny particles now circulate through the air we breathe, the water we drink, and the food we eat. As everyday plastic items break down over time, they form microscopic fragments that can travel long distances and enter the human body through inhalation or ingestion. Once inside the body, these particles may accumulate in organs and interact with biological systems in ways that scientists are only beginning to understand. This review synthesizes current scientific findings on the formation of MPs, their pathways into and persistence within the human body, and their potential health impacts. Although there is no standardized method for measuring MPs, the main analytical techniques used for biological samples are discussed. Furthermore, the toxicity and environmental impacts of plastic types to which humans are exposed are assessed using the EPI Suite™ program developed by the U.S. Environmental Protection Agency (USEPA). Certain MP types, such as polyethylene and polypropylene, appear more toxic due to their low biodegradability. Although evidence increasingly identifies MPs as a growing public health concern, many questions remain unanswered. Health effects related to gastrointestinal and respiratory health systems are examined, while long‑term effects, behavior in human tissues, and associations with chronic diseases—including potential links to cancer—require further multidisciplinary investigation. As global plastic use continues to rise, understanding and mitigating MP exposure will be essential for protecting human health.
- 14 February 2025
- Published by Elsevier in Journal of Environmental Chemical Engineering
- Vol. 13 (2)
A novel gravity-driven dynamic membrane filtration reactor for microplastic removal from plastic recycling facility wastewater
- 14 February 2025
- Published by Elsevier in Journal of Environmental Chemical Engineering
- Vol. 13 (2)
A novel gravity-driven dynamic membrane filtration reactor for microplastic removal from plastic recycling facility wastewater
- 9 April 2024
- Published by Elsevier in Waste Management
- Vol. 181, 79-88
Plastic waste management in recycling facilities: Intentionally generated MPs as an emerging contaminant
- 9 April 2024
- Published by Elsevier in Waste Management
- Vol. 181, 79-88
Plastic waste management in recycling facilities: Intentionally generated MPs as an emerging contaminant
- Open Access
- 15 June 2023
- Published by Omer Halisdemir Universitesi in Ömer Halisdemir Üniversitesi Mühendislik Bilimleri Dergisi
- Vol. 12 (4) , 1
Türkiye’nin bir sanayi şehrinde konut ısıtmasının hava kirliliğine katkısı
In this study, the contribution of fuels (coal + natural gas) used for residential heating in Kayseri city center to air pollution was investigated. For this reason, the amount of emissions released to the atmosphere was calculated by using the natural gas and coal data used in the residences in the 5 (five) year period between 2015-2019 in the province of Kayseri. In addition, the percentage contribution of both residential heating and industrial point sources to air pollution in terms of emissions was compared. The relationship between annual average emission amounts and National Air Quality Monitoring Network data was also revealed. During the 5 years period, the total amount of emissions originating from the fuels used in residences and industries were 6171 tons for PM, 9049 tons for SO2, and 14179 tons for NOx. It has been evaluated that the decrease in PM10 concentrations and the increase in NOX concentrations from 2015 to 2019 may be related to the increase in natural gas use in the city. When evaluated in terms of emission amounts; it has been revealed that PM and SO2 are mostly released from domestic sources, while NOXs are from industrial sources.
- 15 June 2023
- Published by Omer Halisdemir Universitesi in Ömer Halisdemir Üniversitesi Mühendislik Bilimleri Dergisi
- Vol. 12 (4) , 1
Open AccessTürkiye’nin bir sanayi şehrinde konut ısıtmasının hava kirliliğine katkısı
In this study, the contribution of fuels (coal + natural gas) used for residential heating in Kayseri city center to air pollution was investigated. For this reason, the amount of emissions released to the atmosphere was calculated by using the natural gas and coal data used in the residences in the 5 (five) year period between 2015-2019 in the province of Kayseri. In addition, the percentage contribution of both residential heating and industrial point sources to air pollution in terms of emissions was compared. The relationship between annual average emission amounts and National Air Quality Monitoring Network data was also revealed. During the 5 years period, the total amount of emissions originating from the fuels used in residences and industries were 6171 tons for PM, 9049 tons for SO2, and 14179 tons for NOx. It has been evaluated that the decrease in PM10 concentrations and the increase in NOX concentrations from 2015 to 2019 may be related to the increase in natural gas use in the city. When evaluated in terms of emission amounts; it has been revealed that PM and SO2 are mostly released from domestic sources, while NOXs are from industrial sources.
- 16 April 2023
- Published by Taylor & Francis in Journal of Environmental Science and Health, Part A
- Vol. 58 (5) , 498-505
Evaluation of ciprofloxacin (CIP) and clarithromycin (CLA) adsorption with weathered PVC microplastics
The sorption kinetics of two of the most frequently used antibiotics onto recycled (weathered) polyvinyl chloride (PVC) was investigated, using Freundlich and Langmuir isotherm models. Various experimental conditions were set, including pH, contact time, rotational speed, temperature, and initial concentration. The batch experimental results indicated that Freundlich model was better fitted than Langmuir (R2: 98.7 and 84.7, for CIP and CLA respectively). Maximum adsorption capacity is 45.9 mg/g and 22.0 mg/g for CIP and CLA, respectively. Enthalpy (ΔH), and entropy (ΔS) values were negative for CIP, indicating that the reaction was exothermic and spontaneous, respectively. It was vice versa for CLA. Field emission scanning electron microscope (FESEM) and Fourier transform infrared spectrometer (FT-IR) analysis confirmed the physical adsorption mechanism. The results demonstrated that the recycled PVC microplastic has a good capacity for adsorption for both antibiotics.
- 16 April 2023
- Published by Taylor & Francis in Journal of Environmental Science and Health, Part A
- Vol. 58 (5) , 498-505
Evaluation of ciprofloxacin (CIP) and clarithromycin (CLA) adsorption with weathered PVC microplastics
The sorption kinetics of two of the most frequently used antibiotics onto recycled (weathered) polyvinyl chloride (PVC) was investigated, using Freundlich and Langmuir isotherm models. Various experimental conditions were set, including pH, contact time, rotational speed, temperature, and initial concentration. The batch experimental results indicated that Freundlich model was better fitted than Langmuir (R2: 98.7 and 84.7, for CIP and CLA respectively). Maximum adsorption capacity is 45.9 mg/g and 22.0 mg/g for CIP and CLA, respectively. Enthalpy (ΔH), and entropy (ΔS) values were negative for CIP, indicating that the reaction was exothermic and spontaneous, respectively. It was vice versa for CLA. Field emission scanning electron microscope (FESEM) and Fourier transform infrared spectrometer (FT-IR) analysis confirmed the physical adsorption mechanism. The results demonstrated that the recycled PVC microplastic has a good capacity for adsorption for both antibiotics.
- Open Access
- 30 July 2022
- Published by Dogal Afetler ve Cevre Dergisi in Doğal Afetler ve Çevre Dergisi
- Vol. 8 (2) , 341-350
Sanayi Kaynaklı Noktasal Emisyonların Hava Kalitesine Katkısı: Kayseri İli Örneği
Bu çalışmada Kayseri İl Merkezinde endüstriyel amaçlı enerji üretim tesislerine ait enerji santrallerinin hava kirliliğine katkısı araştırılmıştır. Bu nedenle, Kayseri İli’nde 2015-2019 yılları arasındaki 5 (beş) yıllık dönemde sanayide kullanılan doğalgazın yanı sıra, endüstriyel enerji temini için kömür kullanan santrallerden alınan verilerle emisyon miktarları ortaya çıkarılmıştır. Bu kaynakların, hava kirliliğine katkıları da Ulusal Hava Kalitesi İzleme Ağı verileriyle yıllık bazda ayrıca değerlendirilmiştir. Ayrıca, emisyon miktarları ile kirletici konsantrasyonlarının yıllık bazdaki birbiriyle ilişkisi Pearson korelasyonu ile incelenmiştir. Çalışma süresi olan 2015-2019 yıllarını kapsayan 5 yıllık süre zarfında toplam PM (partiküler madde), SO2 ve NOx parametreleri için hesaplanan emisyon miktarları sırasıyla; 1.540 ton, 500 ton ve 10.328 ton şeklindedir. PM, SO2 ve NOx parametreleri için hesaplanan emisyon miktarları (ton/yıl) sonucunda üç kirleticinin emisyon yüzdeleri sırası ile %14, %4 ve %82 şeklindedir. Endüstrilerde enerji santrallerinde kullanılan kömür ile sanayide kullanılan doğalgazın Kayseri İli hava kirliliğine katkısı karşılaştırıldığında, bu parametrelere, PM %89, SO2 %97 ve NOx %62 ile en fazla katkıyı kömürün yaptığı görülmüştür. 2015 yılından 2019 yılına doğru gerçekleşen PM10 konsantrasyonlarında azalma ve NOx konsantrasyonlarındaki artışın, kentte doğalgaz kullanımının artması ile ilişkili olabileceği, endüstriyel doğalgaz ve kömür kullanımı ile SO2 konsantrasyonlarındaki değişimin ilişkilendirilemediği sonucuna varılmıştır. Sanayi tesislerinde enerji eldesi için kömür kullanımı kaynaklı NOx emisyon miktarlarının NOx konsantrasyonu ile yüksek korelasyona sahip olduğu bulunmuştur. Sonraki çalışmalarda evsel kaynaklı kömür ve doğalgaz kullanımının da belirlenmesiyle her bir noktasal kaynağın hava kirliliğine katkısı belirlenebilir.
- 30 July 2022
- Published by Dogal Afetler ve Cevre Dergisi in Doğal Afetler ve Çevre Dergisi
- Vol. 8 (2) , 341-350
Open AccessSanayi Kaynaklı Noktasal Emisyonların Hava Kalitesine Katkısı: Kayseri İli Örneği
Bu çalışmada Kayseri İl Merkezinde endüstriyel amaçlı enerji üretim tesislerine ait enerji santrallerinin hava kirliliğine katkısı araştırılmıştır. Bu nedenle, Kayseri İli’nde 2015-2019 yılları arasındaki 5 (beş) yıllık dönemde sanayide kullanılan doğalgazın yanı sıra, endüstriyel enerji temini için kömür kullanan santrallerden alınan verilerle emisyon miktarları ortaya çıkarılmıştır. Bu kaynakların, hava kirliliğine katkıları da Ulusal Hava Kalitesi İzleme Ağı verileriyle yıllık bazda ayrıca değerlendirilmiştir. Ayrıca, emisyon miktarları ile kirletici konsantrasyonlarının yıllık bazdaki birbiriyle ilişkisi Pearson korelasyonu ile incelenmiştir. Çalışma süresi olan 2015-2019 yıllarını kapsayan 5 yıllık süre zarfında toplam PM (partiküler madde), SO2 ve NOx parametreleri için hesaplanan emisyon miktarları sırasıyla; 1.540 ton, 500 ton ve 10.328 ton şeklindedir. PM, SO2 ve NOx parametreleri için hesaplanan emisyon miktarları (ton/yıl) sonucunda üç kirleticinin emisyon yüzdeleri sırası ile %14, %4 ve %82 şeklindedir. Endüstrilerde enerji santrallerinde kullanılan kömür ile sanayide kullanılan doğalgazın Kayseri İli hava kirliliğine katkısı karşılaştırıldığında, bu parametrelere, PM %89, SO2 %97 ve NOx %62 ile en fazla katkıyı kömürün yaptığı görülmüştür. 2015 yılından 2019 yılına doğru gerçekleşen PM10 konsantrasyonlarında azalma ve NOx konsantrasyonlarındaki artışın, kentte doğalgaz kullanımının artması ile ilişkili olabileceği, endüstriyel doğalgaz ve kömür kullanımı ile SO2 konsantrasyonlarındaki değişimin ilişkilendirilemediği sonucuna varılmıştır. Sanayi tesislerinde enerji eldesi için kömür kullanımı kaynaklı NOx emisyon miktarlarının NOx konsantrasyonu ile yüksek korelasyona sahip olduğu bulunmuştur. Sonraki çalışmalarda evsel kaynaklı kömür ve doğalgaz kullanımının da belirlenmesiyle her bir noktasal kaynağın hava kirliliğine katkısı belirlenebilir.
- Open Access
- 1 October 2019
- Published by Elsevier in Desalination and Water Treatment
- Vol. 164, 56-61
Simultaneous fluoride and nitrate removal from drinking water using mixotrophic denitrification processes in a fixed bed column reactor
- 1 October 2019
- Published by Elsevier in Desalination and Water Treatment
- Vol. 164, 56-61
Open AccessSimultaneous fluoride and nitrate removal from drinking water using mixotrophic denitrification processes in a fixed bed column reactor
- Open Access
Effect of Membrane Type for the Treatment of Organized Industrial Zone (OIZ) Wastewater with a Membrane Bioreactor (MBR): Batch Experiments
Organized industrial zone (OIZ) wastewater is a mixed wastewater that is contributed by both municipal use and from different industrial sectors. Since MBR has advantages over conventional treatment plants, membrane types and fouling become the most important parameters in the treatment of this kind of wastewater. In this study, six different membrane types were used to find the most suitable membrane with the least resistivity to fouling. Three different microfiltration (MF) and ultrafiltration (UF) membranes were operated to estimate their (i) membrane, (ii) cake, (iii) pore, and (iv) total resistances. The highest total resistance was observed in a polyethersulfone (PES) membrane (3.8 × 1010 m−1), while the lowest one was a UF polyvinylidene fluoride (PVDF) membrane with approximately 20 times lower resistance than the highest one. PVDF membranes showed lower total resistances than PES membranes. An MF or a 250 kDa UF membrane could be operated long-term in a membrane bioreactor with the least fouling potential.
Open AccessEffect of Membrane Type for the Treatment of Organized Industrial Zone (OIZ) Wastewater with a Membrane Bioreactor (MBR): Batch Experiments
Organized industrial zone (OIZ) wastewater is a mixed wastewater that is contributed by both municipal use and from different industrial sectors. Since MBR has advantages over conventional treatment plants, membrane types and fouling become the most important parameters in the treatment of this kind of wastewater. In this study, six different membrane types were used to find the most suitable membrane with the least resistivity to fouling. Three different microfiltration (MF) and ultrafiltration (UF) membranes were operated to estimate their (i) membrane, (ii) cake, (iii) pore, and (iv) total resistances. The highest total resistance was observed in a polyethersulfone (PES) membrane (3.8 × 1010 m−1), while the lowest one was a UF polyvinylidene fluoride (PVDF) membrane with approximately 20 times lower resistance than the highest one. PVDF membranes showed lower total resistances than PES membranes. An MF or a 250 kDa UF membrane could be operated long-term in a membrane bioreactor with the least fouling potential.