Heeje Han
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Heeje Han has a total of 6 co-authors. Here are the top co-authors by number of shared publications:
- Hongjoon Kim
Department of Electrical Engineering, Kyungpook National University, Sangyeok-dong, Daegu 41566, Republic of Korea
5 shared publications - Soonwoo Park
School of Electronic and Electrical Engineering, Kyungpook National University, Daegu, South Korea
4 shared publications - Chanwoo Kim
Department of Electrical Engineering
1 shared publication - Hongwoo Park
Agency for Defense Development, Yuseong-gu, Daejeon 34141, Republic of Korea
1 shared publication - Jaemin Bae
Department of Electrical Engineering
1 shared publication Youngki Cho
School of Electronics Engineering Kyungpook National University
1 shared publication
Latest Publications
- Open Access
- 1 January 2025
- Published by Wiley in International Journal of RF and Microwave Computer-Aided Engineering
- Vol. 2025 (1)
Design of a Compact Band‐Pass Filter With an Inclined Phase Shift
This paper presents a design for a band‐pass filter (BPF) with a desired phase shift at the inclined frequency in the passband. This design is achieved by combining a right‐handed transmission line (RHTL), which exhibits positive phase propagation and works as a low‐pass filter (LPF), and a left‐handed transmission line (LHTL), which exhibits negative phase propagation and works as a high‐pass filter (HPF). The proposed BPF simultaneously realizes a desired frequency filtering and phase shifting by cascading proper unit cells of RHTL and LHTL. To verify our proposed idea, we designed four BPFs with similar passband frequencies but different phase delays at a certain frequency in the passband. In the actual experiment, phase delays of 0°, +90°, −90°, and 180° were used, and the phase deviations from the designed phase shift were less than 9.59° at 600 MHz for all four phase delays. The insertion losses were maintained below 1.31 dB. As the RHTL and LHTL were synthesized with lumped elements only, the circuit is compact and applicable to monolithic microwave integrated circuit design.
- 1 January 2025
- Published by Wiley in International Journal of RF and Microwave Computer-Aided Engineering
- Vol. 2025 (1)
Open AccessDesign of a Compact Band‐Pass Filter With an Inclined Phase Shift
This paper presents a design for a band‐pass filter (BPF) with a desired phase shift at the inclined frequency in the passband. This design is achieved by combining a right‐handed transmission line (RHTL), which exhibits positive phase propagation and works as a low‐pass filter (LPF), and a left‐handed transmission line (LHTL), which exhibits negative phase propagation and works as a high‐pass filter (HPF). The proposed BPF simultaneously realizes a desired frequency filtering and phase shifting by cascading proper unit cells of RHTL and LHTL. To verify our proposed idea, we designed four BPFs with similar passband frequencies but different phase delays at a certain frequency in the passband. In the actual experiment, phase delays of 0°, +90°, −90°, and 180° were used, and the phase deviations from the designed phase shift were less than 9.59° at 600 MHz for all four phase delays. The insertion losses were maintained below 1.31 dB. As the RHTL and LHTL were synthesized with lumped elements only, the circuit is compact and applicable to monolithic microwave integrated circuit design.
- Open Access
- 14 August 2023
- Published by Wiley in International Journal of Antennas and Propagation
- Vol. 2023, 1-7
Compact and Broadband-Balanced Amplifier for a Monolithic Microwave Integrated Circuit Using Lumped Elements Only
A flat phase difference across a broad bandwidth is achieved by appropriately combining the positive and negative phase propagation of right-handed (RH) and left-handed (LH) transmission lines (TLs), respectively. Employment of lumped elements provides easy realization of both TLs with the desired frequency passband, characteristic impedance, and phase propagation. The proposed quadrature power divider (QPD) was fabricated in a compact size by only using lumped elements instead of general TLs with a large area and a narrow bandwidth. The fabricated QPD maintains a flat phase difference of 90° ± 8.7° over a frequency range of 1.19–2.96 GHz while its circuit size is 0.036 . Owing to drastic size reduction of the QPD, the proposed balanced amplifier (BA) also could be realized with an extremely compact size of 0.044 and broad bandwidth unlike in other BAs reported in the literature and maintains a return loss of less than −10 dB at each port over the bandwidth of the QPD.
- 14 August 2023
- Published by Wiley in International Journal of Antennas and Propagation
- Vol. 2023, 1-7
Open AccessCompact and Broadband-Balanced Amplifier for a Monolithic Microwave Integrated Circuit Using Lumped Elements Only
A flat phase difference across a broad bandwidth is achieved by appropriately combining the positive and negative phase propagation of right-handed (RH) and left-handed (LH) transmission lines (TLs), respectively. Employment of lumped elements provides easy realization of both TLs with the desired frequency passband, characteristic impedance, and phase propagation. The proposed quadrature power divider (QPD) was fabricated in a compact size by only using lumped elements instead of general TLs with a large area and a narrow bandwidth. The fabricated QPD maintains a flat phase difference of 90° ± 8.7° over a frequency range of 1.19–2.96 GHz while its circuit size is 0.036 . Owing to drastic size reduction of the QPD, the proposed balanced amplifier (BA) also could be realized with an extremely compact size of 0.044 and broad bandwidth unlike in other BAs reported in the literature and maintains a return loss of less than −10 dB at each port over the bandwidth of the QPD.
- 23 November 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Components Letters
- Vol. 32 (4) , 359-362
Low Spurious, Broadband Reflection Frequency Modulation Using an Active Metasurface
By employing varactor diodes in a metasurface, the resonance frequency of a high-impedance surface (HIS) can be changed by a bias voltage. To modulate the frequency of the reflected wave from such surfaces, a phase variation of more than 360° is required. To overcome the phase variation limitation (<360°) in a conventional active metasurface, we fabricated a metasurface with two resonances and manipulated both poles simultaneously to achieve a phase variation exceeding 360° for smooth modulation of the reflection frequency. Because of this wide variation in the reflection phase, it is possible to modulate a broad range of frequencies between 2.75 and 3.25 GHz with up to 1-MHz variation in the modulation frequency. The best spurious-free dynamic range (SFDR) for this frequency range is 20.7 dBc at 3.25 GHz.
- 23 November 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Components Letters
- Vol. 32 (4) , 359-362
Low Spurious, Broadband Reflection Frequency Modulation Using an Active Metasurface
By employing varactor diodes in a metasurface, the resonance frequency of a high-impedance surface (HIS) can be changed by a bias voltage. To modulate the frequency of the reflected wave from such surfaces, a phase variation of more than 360° is required. To overcome the phase variation limitation (<360°) in a conventional active metasurface, we fabricated a metasurface with two resonances and manipulated both poles simultaneously to achieve a phase variation exceeding 360° for smooth modulation of the reflection frequency. Because of this wide variation in the reflection phase, it is possible to modulate a broad range of frequencies between 2.75 and 3.25 GHz with up to 1-MHz variation in the modulation frequency. The best spurious-free dynamic range (SFDR) for this frequency range is 20.7 dBc at 3.25 GHz.
- 30 September 2021
- Published by The Korean Institute of Electrical Engineers in The Transactions of The Korean Institute of Electrical Engineers
- Vol. 70 (9) , 1327-1330
Frequency Conversion of Reflected Wave using an Active Metasurface
By employing varactor diodes in a metasurface, the surface impedance can be changed by a bias voltage, as the resonant frequency altered. In order to convert the frequency of a reflected wave, 360° reflection phase variation is required. This study presents the related theory and demonstrates the frequency conversion through the experimental results. We achieved the reflection frequency conversion which is increased by 50 kHz more than the incident wave of 2.65 GHz, and its SFDR and conversion loss are 7.38 dBc and 5.62 dB, respectively. The proposed metasurface can contribute an efficient improvement in anti-RADAR system fields.
- 30 September 2021
- Published by The Korean Institute of Electrical Engineers in The Transactions of The Korean Institute of Electrical Engineers
- Vol. 70 (9) , 1327-1330
Frequency Conversion of Reflected Wave using an Active Metasurface
By employing varactor diodes in a metasurface, the surface impedance can be changed by a bias voltage, as the resonant frequency altered. In order to convert the frequency of a reflected wave, 360° reflection phase variation is required. This study presents the related theory and demonstrates the frequency conversion through the experimental results. We achieved the reflection frequency conversion which is increased by 50 kHz more than the incident wave of 2.65 GHz, and its SFDR and conversion loss are 7.38 dBc and 5.62 dB, respectively. The proposed metasurface can contribute an efficient improvement in anti-RADAR system fields.
- Open Access
- 6 December 2019
- Published by Wiley in International Journal of Antennas and Propagation
- Vol. 2019, 1-4
Compact Band-Selective Power Divider Using One-Dimensional Metamaterial Structure
A band-selective power divider is demonstrated for the first time. By replacing lumped element right-handed (RH) and left-handed (LH) transmission lines (TL) in a conventional Wilkinson power divider, it is possible to achieve both power division and filtering simultaneously. By utilizing the positive phase propagation property of an RHTL, which works as a low-pass filter, and the negative phase propagation property of an LHTL, which works as a high-pass filter, the band-selective quarter-wave sections required to construct a Wilkinson power divider are implemented. The fabricated circuit shows an insertion loss in the range 1.7 dB–2.5 dB in the passband, with the circuit dimensions of merely 12 mm by 10 mm.
- 6 December 2019
- Published by Wiley in International Journal of Antennas and Propagation
- Vol. 2019, 1-4
Open AccessCompact Band-Selective Power Divider Using One-Dimensional Metamaterial Structure
A band-selective power divider is demonstrated for the first time. By replacing lumped element right-handed (RH) and left-handed (LH) transmission lines (TL) in a conventional Wilkinson power divider, it is possible to achieve both power division and filtering simultaneously. By utilizing the positive phase propagation property of an RHTL, which works as a low-pass filter, and the negative phase propagation property of an LHTL, which works as a high-pass filter, the band-selective quarter-wave sections required to construct a Wilkinson power divider are implemented. The fabricated circuit shows an insertion loss in the range 1.7 dB–2.5 dB in the passband, with the circuit dimensions of merely 12 mm by 10 mm.