Wuyu Li
Wuyu Li has a total of 7 co-authors. Here are the top co-authors by number of shared publications:
- Ke Han
Beijing University of Posts and Telecommunications
1 shared publication - Nijun Ye
Beijing Univ Posts & Telecommun, Sch Elect Engn, Beijing, Peoples R China
1 shared publication - Peiming Wang
Beijing Univ Posts & Telecommun, Sch Elect Engn, Beijing, Peoples R China
1 shared publication Xubing Guo
Beijing Univ Posts & Telecommun, Sch Elect Engn, Beijing, Peoples R China
1 shared publicationYibin Liu
School of Electronic Engineering, Beijing University of Posts and Telecommunications, Haidian District, Beijing 100876, China
1 shared publication- Yibin Liu
Beijing Univ Posts & Telecommun, Sch Elect Engn, Beijing, Peoples R China
1 shared publication
Latest Publications
- Open Access
- 30 April 2021
- Published by IOP Publishing in Journal of Micromechanics and Microengineering
- Vol. 31 (6) , 065004
Design, analysis and fabrication of the CPW resonator loaded by DGS and MEMS capacitors
In this paper, an analytical method of resonant frequency, tuning range, the effective relative dielectric constant, and characteristic impedance is proposed, which is for coplanar waveguide (CPW) resonator loaded by defected ground structure (DGS) and micro-electromechanical systems (MEMS) capacitors. The analytical solution is achieved by an employing equivalent method. The resonant frequency, tuning range, and effective relative dielectric constant are obtained by the analytical solution. For verifying the effectiveness of the proposed method, a CPW tunable bandstop filter (BSF) with DGS and MEMS capacitors is designed, simulated, and fabricated, results show good effectiveness of the proposed analysis method. By changing the height of the MEMS beam with the actuation voltage, the designed BSF can switch the center frequency among three states (i.e. 18.5 GHz, 18.2 GHz, 17.5 GHz, respectively), and fractional bandwidth is changed as well (i.e. 37.8%, 45.6%, 49.5%, respectively).
- 30 April 2021
- Published by IOP Publishing in Journal of Micromechanics and Microengineering
- Vol. 31 (6) , 065004
Open AccessDesign, analysis and fabrication of the CPW resonator loaded by DGS and MEMS capacitors
In this paper, an analytical method of resonant frequency, tuning range, the effective relative dielectric constant, and characteristic impedance is proposed, which is for coplanar waveguide (CPW) resonator loaded by defected ground structure (DGS) and micro-electromechanical systems (MEMS) capacitors. The analytical solution is achieved by an employing equivalent method. The resonant frequency, tuning range, and effective relative dielectric constant are obtained by the analytical solution. For verifying the effectiveness of the proposed method, a CPW tunable bandstop filter (BSF) with DGS and MEMS capacitors is designed, simulated, and fabricated, results show good effectiveness of the proposed analysis method. By changing the height of the MEMS beam with the actuation voltage, the designed BSF can switch the center frequency among three states (i.e. 18.5 GHz, 18.2 GHz, 17.5 GHz, respectively), and fractional bandwidth is changed as well (i.e. 37.8%, 45.6%, 49.5%, respectively).
- Open Access
- 4 December 2019
- Published by Wiley in International Journal of Antennas and Propagation
- Vol. 2019, 1-7
Flexible Phase Difference of 4 × 4 Butler Matrix without Phase-Shifters and Crossovers
This paper proposes a new Butler matrix topology. The proposed Butler matrix consists of only four couplers without phase shifters and crossovers. The output phase difference is relatively flexible. Compared with the phase differences (±45° and ±135°) generated by the conventional Butler matrix, the proposed design can generate different sets of phase differences, which can be realized from −180° to 180°. The proposed new Butler matrix replaces the traditional 90° coupler with arbitrary phase-difference couplers. In this paper, closed-form design equations are derived and presented. A 4 × 4 Butler matrix with output phase differences of −30°, +150°, −120°, and +60° is designed according to equations. The 4 × 4 Butler is meant to operate at 2 GHz. The simulation results show that the amplitude unbalance is less than 0.1 dB, the phase mismatch is within 1°, the return loss is higher than 29 dB, and the isolation is higher than 32 dB.
- 4 December 2019
- Published by Wiley in International Journal of Antennas and Propagation
- Vol. 2019, 1-7
Open AccessFlexible Phase Difference of 4 × 4 Butler Matrix without Phase-Shifters and Crossovers
This paper proposes a new Butler matrix topology. The proposed Butler matrix consists of only four couplers without phase shifters and crossovers. The output phase difference is relatively flexible. Compared with the phase differences (±45° and ±135°) generated by the conventional Butler matrix, the proposed design can generate different sets of phase differences, which can be realized from −180° to 180°. The proposed new Butler matrix replaces the traditional 90° coupler with arbitrary phase-difference couplers. In this paper, closed-form design equations are derived and presented. A 4 × 4 Butler matrix with output phase differences of −30°, +150°, −120°, and +60° is designed according to equations. The 4 × 4 Butler is meant to operate at 2 GHz. The simulation results show that the amplitude unbalance is less than 0.1 dB, the phase mismatch is within 1°, the return loss is higher than 29 dB, and the isolation is higher than 32 dB.