T. M. Paramonova
T. M. Paramonova has a total of 15 co-authors. Here are the top co-authors by number of shared publications:
- Oleksandr Leonidovich Shubenko
Anatolii Pidhornyi Institute of Power Machines and Systems of the National Academy of Sciences of Ukraine
2 shared publications - Daria Senetska
Department of Optimization of Processes and Designs of Turbomachines Anatolii Pidhornyi Institute of Mechanical Engineering Problems of the National Academy of Sciences of Ukraine, Kharkiv, Ukraine
1 shared publication O. V. Kotulska
Anatolii Pidhornyi Institute of Mechanical Engineering Problems of NAS of Ukraine
1 shared publication- Oleksandr Kozlokov1 shared publication
Olga Kotulska
1 shared publicationOlga Valerievna Kotulska
A.N. Podgorny Institute for Mechanical Engineering Problems (IPMach) NAS of Ukraine
1 shared publication
Latest Publications
- Open Access
- 15 February 2024
- Published by Institute of Engineering Thermophysics of NAS of Ukraine in Thermophysics and Thermal Power Engineering
- Vol. 46 (1) , 84-92
REFINED PHYSICAL MODEL OF STEAM FLOW IN THE LOW-PRESSURE PART OF A HIGH-POWER TURBINE IN LOW-FLOW RATE MODES
Analytical methods for calculating the performance of the turbine are operational as long as the “layered” character of the steam flow is preserved in the flow part. However, as shown by experimental studies, the character of the flow changes significantly in low-flow rate modes. In these cases, existing methods of three-dimensional calculations require reliable formation of boundary conditions. The purpose of this study is to analyze the characteristics of low-pressure cylinder (LPC) stages operating in high-power stationary steam turbines, and to form physical models of the flow of the working medium (steam) in such stages at low-flow rate modes, taking into account their location in the flow part. It is advisable to imagine the physical model of the movement of steam in the turbine, starting from the last stage of the LPC and the outlet nozzle, in which separation of flow from the hub the develops. Its formation occurs when the relative volumetric flow rate decreases, starting with = 0.8, depending on the angle b2к at the root of the working blades. A decrease in the operating mode of the LPC turbine stages is also accompanied by a decrease the flow speed in the peripheral zone and a negative angle of attack at the flow entry into the channels of the impeller. On the concave surface of the profile part of the blade, a separation area is formed, which rotates in the rim clearance in the circumferential direction. Reverse flow from the inlet part of the channels of the impeller into the rim clearance occur when the static pressure in it exceeds the full pressure of the flow coming out of the channels of the guide apparatus. Turbulization of the flow of the rotating vortex leads to large irreversible losses of the mechanical energy of the moving flow, which are converted into heat, heating the mass of the working medium of the vortex and the main flow averaged through the channels of the working blade. Thus, the analysis of the gas-dynamic structure of the flow and its thermal state made it possible to clarify the physical model of the steam flow in the LPC at low-flow rate modes.
- 15 February 2024
- Published by Institute of Engineering Thermophysics of NAS of Ukraine in Thermophysics and Thermal Power Engineering
- Vol. 46 (1) , 84-92
Open AccessREFINED PHYSICAL MODEL OF STEAM FLOW IN THE LOW-PRESSURE PART OF A HIGH-POWER TURBINE IN LOW-FLOW RATE MODES
Analytical methods for calculating the performance of the turbine are operational as long as the “layered” character of the steam flow is preserved in the flow part. However, as shown by experimental studies, the character of the flow changes significantly in low-flow rate modes. In these cases, existing methods of three-dimensional calculations require reliable formation of boundary conditions. The purpose of this study is to analyze the characteristics of low-pressure cylinder (LPC) stages operating in high-power stationary steam turbines, and to form physical models of the flow of the working medium (steam) in such stages at low-flow rate modes, taking into account their location in the flow part. It is advisable to imagine the physical model of the movement of steam in the turbine, starting from the last stage of the LPC and the outlet nozzle, in which separation of flow from the hub the develops. Its formation occurs when the relative volumetric flow rate decreases, starting with = 0.8, depending on the angle b2к at the root of the working blades. A decrease in the operating mode of the LPC turbine stages is also accompanied by a decrease the flow speed in the peripheral zone and a negative angle of attack at the flow entry into the channels of the impeller. On the concave surface of the profile part of the blade, a separation area is formed, which rotates in the rim clearance in the circumferential direction. Reverse flow from the inlet part of the channels of the impeller into the rim clearance occur when the static pressure in it exceeds the full pressure of the flow coming out of the channels of the guide apparatus. Turbulization of the flow of the rotating vortex leads to large irreversible losses of the mechanical energy of the moving flow, which are converted into heat, heating the mass of the working medium of the vortex and the main flow averaged through the channels of the working blade. Thus, the analysis of the gas-dynamic structure of the flow and its thermal state made it possible to clarify the physical model of the steam flow in the LPC at low-flow rate modes.
- Open Access
- 4 June 2023
- Published by National Technical University Kharkiv Polytechnic Institute in Bulletin of the National Technical University "KhPI". Series: Hydraulic machines and hydraulic units
- No. 2,p. 12-17
POWER EXPENSES TO DRIVE A TURBINE STAGE UNDER LOW-FLOW MODES
The task of determining the power consumption during the operation of the turbine stage in the low-cost mode is considered. To solve it, a theoreticalexperimental approach was used, based on the one-dimensional theory of the movement of a incompressible working medium and the results of an experimental study of a number of models of large fanning degrees, in which the working medium is air. When operating heating turbines, the lowpressure cylinders work in the area of low-cost modes up to 85 % of the time, both with a partially and completely closed rotary diaphragm of the regulating stage. When the volumetric flow rate of steam in the flow part of the low-pressure cylinder at low-flow modes is reduced, a sleeve separation of the flow develops and a vortex is formed in the inter-crown gap of the stage. The mode in which the power supplied to the impeller is spent on maintaining these currents corresponds to the "pure" ventilation mode. In contrast to the existing methods for determining the ventilation power losses in the stages of large fanning, the paper proposes a dependence based on the geometric configuration of the stages of the low-pressure cylinder of the heating turbines and their operating conditions. Taking into account the processes in the stage and the data obtained on the experimental stand, formulas were determined account the components of power losses - the function of the influence of the flow exit angles from the guide apparatus of the stage; influence of fanning l/Dmid; influence of the relative width of the working blade B/Dmid and the angle of inclination of the peripheral meridional circuit γm. The obtained dependences, which allow determining the coefficients of power consumption for the stage in the ventilation mode and the operation mode before idling, make it possible to calculate power consumption in the entire range of changes in low-flow modes. On the example of the last stage of the T-250/300-240 turbine, a comparison of the results of calculation studies according to the proposed dependence with the results obtained in real conditions of full-scale experiments was performed, which showed that their difference does not exceed 5 %.
- 4 June 2023
- Published by National Technical University Kharkiv Polytechnic Institute in Bulletin of the National Technical University "KhPI". Series: Hydraulic machines and hydraulic units
- No. 2,p. 12-17
Open AccessPOWER EXPENSES TO DRIVE A TURBINE STAGE UNDER LOW-FLOW MODES
The task of determining the power consumption during the operation of the turbine stage in the low-cost mode is considered. To solve it, a theoreticalexperimental approach was used, based on the one-dimensional theory of the movement of a incompressible working medium and the results of an experimental study of a number of models of large fanning degrees, in which the working medium is air. When operating heating turbines, the lowpressure cylinders work in the area of low-cost modes up to 85 % of the time, both with a partially and completely closed rotary diaphragm of the regulating stage. When the volumetric flow rate of steam in the flow part of the low-pressure cylinder at low-flow modes is reduced, a sleeve separation of the flow develops and a vortex is formed in the inter-crown gap of the stage. The mode in which the power supplied to the impeller is spent on maintaining these currents corresponds to the "pure" ventilation mode. In contrast to the existing methods for determining the ventilation power losses in the stages of large fanning, the paper proposes a dependence based on the geometric configuration of the stages of the low-pressure cylinder of the heating turbines and their operating conditions. Taking into account the processes in the stage and the data obtained on the experimental stand, formulas were determined account the components of power losses - the function of the influence of the flow exit angles from the guide apparatus of the stage; influence of fanning l/Dmid; influence of the relative width of the working blade B/Dmid and the angle of inclination of the peripheral meridional circuit γm. The obtained dependences, which allow determining the coefficients of power consumption for the stage in the ventilation mode and the operation mode before idling, make it possible to calculate power consumption in the entire range of changes in low-flow modes. On the example of the last stage of the T-250/300-240 turbine, a comparison of the results of calculation studies according to the proposed dependence with the results obtained in real conditions of full-scale experiments was performed, which showed that their difference does not exceed 5 %.
- Open Access
- 26 December 2019
- Published by National Technical University Kharkiv Polytechnic Institute in Bulletin of the National Technical University "KhPI". Series: Hydraulic machines and hydraulic units
- No. 2,p. 117-120
ANALYSIS OF THE STATE AND TRENDS OF RENEWABLE ENERGY DEVELOPMENT IN UKRAINE
АНАЛІЗ СТАНУ ТА ТЕНДЕНЦІЇ РОЗВИТКУ ВІДНОВЛЮВАНОЇ ЕНЕРГЕТИКИ В УКРАЇНІ
- 26 December 2019
- Published by National Technical University Kharkiv Polytechnic Institute in Bulletin of the National Technical University "KhPI". Series: Hydraulic machines and hydraulic units
- No. 2,p. 117-120
Open AccessANALYSIS OF THE STATE AND TRENDS OF RENEWABLE ENERGY DEVELOPMENT IN UKRAINE
АНАЛІЗ СТАНУ ТА ТЕНДЕНЦІЇ РОЗВИТКУ ВІДНОВЛЮВАНОЇ ЕНЕРГЕТИКИ В УКРАЇНІ
- Open Access
- 30 October 2017
- Published by National Technical University Kharkiv Polytechnic Institute in NTU "KhPI" Bulletin: Power and heat engineering processes and equipment
- No. 11
Appropriateness of the Use of End Seals with Crossed Crests for the High Pressure Cylinder
Appropriateness of the Use of End Seals with Crossed Crests for the High Pressure Cylinder
- 30 October 2017
- Published by National Technical University Kharkiv Polytechnic Institute in NTU "KhPI" Bulletin: Power and heat engineering processes and equipment
- No. 11
Open AccessAppropriateness of the Use of End Seals with Crossed Crests for the High Pressure Cylinder
Appropriateness of the Use of End Seals with Crossed Crests for the High Pressure Cylinder