Samir Paulo Jasper
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Samir Paulo Jasper has a total of 46 co-authors. Here are the top co-authors by number of shared publications:
- Gabriel Ganancini Zimmermann
Universidade Federal do Paraná (UFPR), Brasil
23 shared publications - Daniel Savi
Universidade Federal do Paraná (UFPR), Brazil
15 shared publications - Leonardo Leonidas Kmiecik
Universidade Federal do Paraná, Brazil
11 shared publications - Eduardo Alves Gracietti
Universidade Federal do Paraná (UFPR), Brasil
8 shared publications - Lauro Strapasson Neto
Universidade Federal do Paraná, Brazil
8 shared publications - William Santiago de Mendonça
Universidade Federal do Paraná (UFPR), Brasil
8 shared publications
Latest Publications
- Open Access
- 26 January 2026
- Published by Editorial CSIC in Spanish Journal of Agricultural Research
- Vol. 23 (4)
Electronic rod profilometer for soil mobilization measurement
Aim of the study: This study aimed to develop and validate an electronically enhanced rod profilometer capable of operating independently under field conditions and to compare laser, LiDAR, and ultrasonic sensors to identify the technology least affected by environmental interference during soil surface roughness measurements. Area of study: Federal University of Parana, Curitiba, Brazil. Material and methods: A laboratory experiment was carried out using a completely randomized design, comparing a conventional rod profilometer with electronic profilometers equipped with laser, LiDAR, and ultrasonic sensors. Modified roughness, elevated area, mobilized area, blistering, and soil thickness were evaluated, with seven replicates per treatment. Data were tested for normality and homogeneity and subsequently subjected to analysis of variance. When significant differences were detected, means were compared using the Student–Newman–Keuls (SNK) test at a 5% significance level. Main results: The electronically enhanced rod profilometer demonstrated satisfactory accuracy, precision, and reliability when compared to the conventional method, confirming the validation of the equipment. Among the evaluated sensors, the ultrasonic sensor exhibited the most consistent and reliable performance for stem readings due to its wider beam angle, which increased detection probability and reduced susceptibility to environmental interferences such as solar incidence and soil reflectance. Research highlights: Sensor selection critically affects measurement reliability in electronically enhanced rod profilometry under field conditions.
- 26 January 2026
- Published by Editorial CSIC in Spanish Journal of Agricultural Research
- Vol. 23 (4)
Open AccessElectronic rod profilometer for soil mobilization measurement
Aim of the study: This study aimed to develop and validate an electronically enhanced rod profilometer capable of operating independently under field conditions and to compare laser, LiDAR, and ultrasonic sensors to identify the technology least affected by environmental interference during soil surface roughness measurements. Area of study: Federal University of Parana, Curitiba, Brazil. Material and methods: A laboratory experiment was carried out using a completely randomized design, comparing a conventional rod profilometer with electronic profilometers equipped with laser, LiDAR, and ultrasonic sensors. Modified roughness, elevated area, mobilized area, blistering, and soil thickness were evaluated, with seven replicates per treatment. Data were tested for normality and homogeneity and subsequently subjected to analysis of variance. When significant differences were detected, means were compared using the Student–Newman–Keuls (SNK) test at a 5% significance level. Main results: The electronically enhanced rod profilometer demonstrated satisfactory accuracy, precision, and reliability when compared to the conventional method, confirming the validation of the equipment. Among the evaluated sensors, the ultrasonic sensor exhibited the most consistent and reliable performance for stem readings due to its wider beam angle, which increased detection probability and reduced susceptibility to environmental interferences such as solar incidence and soil reflectance. Research highlights: Sensor selection critically affects measurement reliability in electronically enhanced rod profilometry under field conditions.
- Open Access
- 1 January 2026
- Published by FapUNIFESP (SciELO) in Ciência Rural
- Vol. 56 (6)
Radial and bias-ply tires used in sugarcane transshipment deflection and soil pressure at two depths under controlled conditions
Soil compaction caused by heavy machinery traffic is one of the main physical constraints to crop production, especially in sugarcane systems where tire type and load intensity strongly affect soil structure. Understanding how tire construction modifies deflection behavior and stress transmission is essential to support more sustainable mechanization practices. This study evaluated the performance of radial and bias-ply agricultural tires used in sugarcane transshipments, focusing on their deflection patterns and stresses applied to the soil. Tests were carried out with a hydraulic press applying progressive loads up to 6100 kgf on both tire types, calibrated at 45 psi (310 kPa). Vertical and horizontal deflections were measured with displacement sensors, while soil stresses were monitored with load cells installed at depths of 0.10 and 0.20 m. Data were analyzed using analysis of covariance (ANCOVA), considering load as a covariate and tire type as a fixed factor. Results showed that radial tires presented greater sensitivity in vertical deflection but lower lateral deformation, while bias-ply tires displayed higher lateral deflection and concentrated stresses at the soil surface. At 0.20 m, pressures were attenuated, but the interaction between load and tire type revealed that radials dissipated stress more gradually. These findings demonstrated that tire construction directly influences the magnitude and distribution of soil stress. The adoption of radial tires in sugarcane production systems can mitigate soil compaction and contribute to the sustainability of mechanized agriculture.
- 1 January 2026
- Published by FapUNIFESP (SciELO) in Ciência Rural
- Vol. 56 (6)
Open AccessRadial and bias-ply tires used in sugarcane transshipment deflection and soil pressure at two depths under controlled conditions
Soil compaction caused by heavy machinery traffic is one of the main physical constraints to crop production, especially in sugarcane systems where tire type and load intensity strongly affect soil structure. Understanding how tire construction modifies deflection behavior and stress transmission is essential to support more sustainable mechanization practices. This study evaluated the performance of radial and bias-ply agricultural tires used in sugarcane transshipments, focusing on their deflection patterns and stresses applied to the soil. Tests were carried out with a hydraulic press applying progressive loads up to 6100 kgf on both tire types, calibrated at 45 psi (310 kPa). Vertical and horizontal deflections were measured with displacement sensors, while soil stresses were monitored with load cells installed at depths of 0.10 and 0.20 m. Data were analyzed using analysis of covariance (ANCOVA), considering load as a covariate and tire type as a fixed factor. Results showed that radial tires presented greater sensitivity in vertical deflection but lower lateral deformation, while bias-ply tires displayed higher lateral deflection and concentrated stresses at the soil surface. At 0.20 m, pressures were attenuated, but the interaction between load and tire type revealed that radials dissipated stress more gradually. These findings demonstrated that tire construction directly influences the magnitude and distribution of soil stress. The adoption of radial tires in sugarcane production systems can mitigate soil compaction and contribute to the sustainability of mechanized agriculture.
- Open Access
- 1 January 2026
- Published by FapUNIFESP (SciELO) in Ciência Rural
- Vol. 56 (7)
Operational performance of an agricultural tractor with different tire technologies on two surfaces
Standard, IF, and VF radial tire technologies have brought significant advancements in load capacity and the operational efficiency of modern agricultural tractors. These improvements have contributed to reduced fuel consumption and greater sustainability in agricultural operations. However, limited research exists on the performance of agricultural tractors equipped with different tire technologies under real field conditions. Therefore, this study evaluated the operational performance of an agricultural tractor fitted with standard, IF, and VF radial tires on both concrete and firm soil surfaces. The experiment followed a strip-plot randomized block design with three tire technologies (standard, IF, and VF) as main plots and two surfaces (concrete and soil) as subplots, with five replicates, totaling 30 experimental units. Parameters monitored included engine speed, wheel slip, operating speed, drawbar pull, drawbar power and efficiency, hourly and specific fuel consumption, and engine thermal efficiency. Results showed that the concrete surface enabled higher speeds and lower fuel consumption, while the firm soil required greater engine speed and exhibited higher slip. VF tires outperformed standard tires in energy efficiency, traction, and contact area, offering higher speeds and reduced slip. However, under firm soil conditions, VF tires required additional ballast to reach optimal performance. IF tires demonstrated intermediate performance.
- 1 January 2026
- Published by FapUNIFESP (SciELO) in Ciência Rural
- Vol. 56 (7)
Open AccessOperational performance of an agricultural tractor with different tire technologies on two surfaces
Standard, IF, and VF radial tire technologies have brought significant advancements in load capacity and the operational efficiency of modern agricultural tractors. These improvements have contributed to reduced fuel consumption and greater sustainability in agricultural operations. However, limited research exists on the performance of agricultural tractors equipped with different tire technologies under real field conditions. Therefore, this study evaluated the operational performance of an agricultural tractor fitted with standard, IF, and VF radial tires on both concrete and firm soil surfaces. The experiment followed a strip-plot randomized block design with three tire technologies (standard, IF, and VF) as main plots and two surfaces (concrete and soil) as subplots, with five replicates, totaling 30 experimental units. Parameters monitored included engine speed, wheel slip, operating speed, drawbar pull, drawbar power and efficiency, hourly and specific fuel consumption, and engine thermal efficiency. Results showed that the concrete surface enabled higher speeds and lower fuel consumption, while the firm soil required greater engine speed and exhibited higher slip. VF tires outperformed standard tires in energy efficiency, traction, and contact area, offering higher speeds and reduced slip. However, under firm soil conditions, VF tires required additional ballast to reach optimal performance. IF tires demonstrated intermediate performance.
- Open Access
- 4 September 2025
- Published by MDPI AG in Agriengineering
- Vol. 7 (9) , 289
Mass Impact of a Mounted Sprayer on the Operational Balance of an Agricultural Tractor
The operational stability of agricultural tractors is directly influenced by the mass distribution between axles, particularly when using mounted implements with variable loads. This study aimed to evaluate how different masses of a mounted sprayer (550 kg, 850 kg, and 1150 kg) and tire inflation pressures (151.7–193.1 kPa) affect the load distribution between axles, tire contact area, center of gravity (CG) displacement, and tractor lead ratio. A 3 × 4 factorial design was adopted with a statistical analysis of key parameters across 12 experimental combinations. The results demonstrated that increasing implement mass significantly shifted the load toward the rear axle, reducing the front axle load by up to 46% and displacing the CG rearward by more than 11 cm, thereby compromising stability. Tire pressure, as well as the interaction between mass and pressure, also exhibited statistically significant influence on load distribution and CG positioning while modulating the tire contact area. The lead ratio increased linearly with mass, exceeding the recommended 5% threshold when the sprayer was at full capacity. These findings indicate that while the implement mass exerts a dominant effect, tire pressure management represents a statistically relevant factor for stability, requiring integrated management that considers the interaction between ballasting and tire inflation to mitigate operational risks.
- 4 September 2025
- Published by MDPI AG in Agriengineering
- Vol. 7 (9) , 289
Open AccessMass Impact of a Mounted Sprayer on the Operational Balance of an Agricultural Tractor
The operational stability of agricultural tractors is directly influenced by the mass distribution between axles, particularly when using mounted implements with variable loads. This study aimed to evaluate how different masses of a mounted sprayer (550 kg, 850 kg, and 1150 kg) and tire inflation pressures (151.7–193.1 kPa) affect the load distribution between axles, tire contact area, center of gravity (CG) displacement, and tractor lead ratio. A 3 × 4 factorial design was adopted with a statistical analysis of key parameters across 12 experimental combinations. The results demonstrated that increasing implement mass significantly shifted the load toward the rear axle, reducing the front axle load by up to 46% and displacing the CG rearward by more than 11 cm, thereby compromising stability. Tire pressure, as well as the interaction between mass and pressure, also exhibited statistically significant influence on load distribution and CG positioning while modulating the tire contact area. The lead ratio increased linearly with mass, exceeding the recommended 5% threshold when the sprayer was at full capacity. These findings indicate that while the implement mass exerts a dominant effect, tire pressure management represents a statistically relevant factor for stability, requiring integrated management that considers the interaction between ballasting and tire inflation to mitigate operational risks.
- Open Access
- 1 January 2025
- Published by FapUNIFESP (SciELO) in Revista Brasileira de Engenharia Agrícola E Ambiental
- Vol. 29 (12)
Operational and energy performance of a powershift transmission tractor during tillage at different speeds
Agricultural machinery plays a key role in optimizing crop yields. In tillage operations, it is essential to analyze both operational and energy performance variables. Continuous research is needed to quantify performance without compromising soil conservation, particularly with modern agricultural tractors, to update strategies, increase productivity and ensure the sustainability of mechanized operations. This study aimed to assess the energy and operational efficiency of an agricultural tractor (John Deere®, model 8400R), during subsoiling at different speeds, using five gear settings (A, B, C, D and E, corresponding to gears F5, F6, F7, F8 and F9), with a nominal engine speed of 2,100 rpm. The parameters evaluated were operating speed, wheel slip, engine speed, drawbar force, drawbar efficiency, hourly fuel consumption, fuel consumption per unit area, brake specific fuel consumption, brake thermal efficiency, and field capacity. The experiment followed a randomized block design. Analysis of variance indicated significant improvements in operating speed, wheel slippage, engine speed, drawbar force and drawbar efficiency as the gears shifted from A to E. Correlation analysis showed strong relationships between operating speed and parameters such as wheel slippage, drawback force and drawback efficiency, hourly fuel consumption and operational field capacity. Gear D was the most efficient for tillage. Although gear E improved operational performance, it reduced energy efficiency, indicating a trade-off between speed and fuel economy.
- 1 January 2025
- Published by FapUNIFESP (SciELO) in Revista Brasileira de Engenharia Agrícola E Ambiental
- Vol. 29 (12)
Open AccessOperational and energy performance of a powershift transmission tractor during tillage at different speeds
Agricultural machinery plays a key role in optimizing crop yields. In tillage operations, it is essential to analyze both operational and energy performance variables. Continuous research is needed to quantify performance without compromising soil conservation, particularly with modern agricultural tractors, to update strategies, increase productivity and ensure the sustainability of mechanized operations. This study aimed to assess the energy and operational efficiency of an agricultural tractor (John Deere®, model 8400R), during subsoiling at different speeds, using five gear settings (A, B, C, D and E, corresponding to gears F5, F6, F7, F8 and F9), with a nominal engine speed of 2,100 rpm. The parameters evaluated were operating speed, wheel slip, engine speed, drawbar force, drawbar efficiency, hourly fuel consumption, fuel consumption per unit area, brake specific fuel consumption, brake thermal efficiency, and field capacity. The experiment followed a randomized block design. Analysis of variance indicated significant improvements in operating speed, wheel slippage, engine speed, drawbar force and drawbar efficiency as the gears shifted from A to E. Correlation analysis showed strong relationships between operating speed and parameters such as wheel slippage, drawback force and drawback efficiency, hourly fuel consumption and operational field capacity. Gear D was the most efficient for tillage. Although gear E improved operational performance, it reduced energy efficiency, indicating a trade-off between speed and fuel economy.
- Open Access
- 1 January 2025
- Published by FapUNIFESP (SciELO) in Ciência Rural
- Vol. 55 (1) , e20240141
Energy efficiency of four-wheel drive tractor in sowing operation
The breakthrough of articulated tractors has led to a significant increase in productivity and a cost reduction of agricultural operations. The performance of the tractor implement system depends on the understanding of the tractors’ energy parameters. Fertilizer seeders operate between 6 and 9 km h-1, while seed drills allow higher speeds. Increasing sowing speed improves operational efficiency. However, it is important to adequately set the machinery, to optimize the energy parameters, considering the balance between productivity and sustainability. This study evaluated the energy and operating parameters of a 398kW articulated agricultural tractor in a sowing operation at different speeds. The experiment was conducted in a complete randomized block design. Five theoretical speeds were chosen for the sowing operation (6, 7, 8, 9 and 10 km h-1), with seven replications (35 units). The tractor operating parameters were measured: operational speed, slippage, engine speed, hourly fuel consumption, engine thermal efficiency, specific fuel consumption, drawbar force, drawbar efficiency, fuel consumption per area and field operating capacity. The data were subjected to normality test, when significant, variance analysis. Results showed high field capacity in the highest speed and low fuel consumption per area at the highest speed.
- 1 January 2025
- Published by FapUNIFESP (SciELO) in Ciência Rural
- Vol. 55 (1) , e20240141
Open AccessEnergy efficiency of four-wheel drive tractor in sowing operation
The breakthrough of articulated tractors has led to a significant increase in productivity and a cost reduction of agricultural operations. The performance of the tractor implement system depends on the understanding of the tractors’ energy parameters. Fertilizer seeders operate between 6 and 9 km h-1, while seed drills allow higher speeds. Increasing sowing speed improves operational efficiency. However, it is important to adequately set the machinery, to optimize the energy parameters, considering the balance between productivity and sustainability. This study evaluated the energy and operating parameters of a 398kW articulated agricultural tractor in a sowing operation at different speeds. The experiment was conducted in a complete randomized block design. Five theoretical speeds were chosen for the sowing operation (6, 7, 8, 9 and 10 km h-1), with seven replications (35 units). The tractor operating parameters were measured: operational speed, slippage, engine speed, hourly fuel consumption, engine thermal efficiency, specific fuel consumption, drawbar force, drawbar efficiency, fuel consumption per area and field operating capacity. The data were subjected to normality test, when significant, variance analysis. Results showed high field capacity in the highest speed and low fuel consumption per area at the highest speed.
- Open Access
- 1 January 2025
- Published by FapUNIFESP (SciELO) in Revista Brasileira de Engenharia Agrícola E Ambiental
- Vol. 29 (2) , e284914
Impact of on-farm and industrial treatments on seed longitudinal distribution for soybeans
Adequate seed placement is essential for consistent crop emergence and initial growth. Pneumatic seed metering systems offer superior longitudinal seed distribution accuracy compared to traditional methods, yet certain factors can influence this precision. For instance, seed physical properties may be altered by phytosanitary treatments applied either on-farm or industrially. This study examined the effects of phytosanitary treatment type and graphite addition on soybean seed deposition using an electric-driven pneumatic feeder under simulated sowing conditions. Seed distribution was monitored with an optical sensor. Four treatment groups were established: untreated without graphite, untreated with graphite added, on-farm treated with graphite, and industrially treated with graphite. Parameters assessed included average spacing between seeds, coefficient of variation, precision index, multiple and failed spacings, and percentage of acceptable spacing. Results indicate that prior seed treatment does not significantly affect overall planting accuracy. However, seed spacing varied between the untreated and on-farm treated groups, with the latter demonstrating closer proximity to optimal values. Both on-farm and industrial treatments yielded more uniform seed deposition, as indicated by a lower coefficient of variation. Regardless of seed treatment, the pneumatic feeder consistently performed effectively.
- 1 January 2025
- Published by FapUNIFESP (SciELO) in Revista Brasileira de Engenharia Agrícola E Ambiental
- Vol. 29 (2) , e284914
Open AccessImpact of on-farm and industrial treatments on seed longitudinal distribution for soybeans
Adequate seed placement is essential for consistent crop emergence and initial growth. Pneumatic seed metering systems offer superior longitudinal seed distribution accuracy compared to traditional methods, yet certain factors can influence this precision. For instance, seed physical properties may be altered by phytosanitary treatments applied either on-farm or industrially. This study examined the effects of phytosanitary treatment type and graphite addition on soybean seed deposition using an electric-driven pneumatic feeder under simulated sowing conditions. Seed distribution was monitored with an optical sensor. Four treatment groups were established: untreated without graphite, untreated with graphite added, on-farm treated with graphite, and industrially treated with graphite. Parameters assessed included average spacing between seeds, coefficient of variation, precision index, multiple and failed spacings, and percentage of acceptable spacing. Results indicate that prior seed treatment does not significantly affect overall planting accuracy. However, seed spacing varied between the untreated and on-farm treated groups, with the latter demonstrating closer proximity to optimal values. Both on-farm and industrial treatments yielded more uniform seed deposition, as indicated by a lower coefficient of variation. Regardless of seed treatment, the pneumatic feeder consistently performed effectively.
- Open Access
- 1 January 2025
- Published by GN1 Sistemas e Publicacoes Ltd. in Revista Ciência Agronômica
- Vol. 56, 1-5
Effect of pneumatic dosing mechanism angle on corn seed deposition
Maize sowing is essential for agricultural production and food security. Technological advances, such as electric pneumatic feeders and integrated software were developed with a view to economic and environmental sustainability. However, there are limitations in the knowledge of the physical phenomena related to sowing, which can affect the efficiency and reliability of these technologies. In addition to the terrain's irregularity, the slope also deserves scientific investigation to verify disturbances in the maize sowing process. The objective was to evaluate the deposition of corn seeds in longitudinal and transverse slopes using a pneumatic doser. The experiment was made on a static seeding bench, simulating the different inclinations. The results showed that the longitudinal inclination did not influence the acceptable spacing of the seeds, but the transverse variations resulted in a higher incidence of undesirable spacing. The study shown that the sowing operation when performed under longitudinal inclination results in a decrease in the accuracy of corn seed deposition, which can be mitigated by level cultivation. Transversal slopes influenced the parameters of acceptable, double and gap spacing during sowing. A semeadura de milho é essencial para a produção agrícola e segurança alimentar. Avanços tecnológicos, como dosadores pneumáticos elétricos e softwares integrados, têm sido desenvolvidos visando a sustentabilidade econômica e ambiental. No entanto, há limitações no conhecimento dos fenômenos físicos relacionados à semeadura, o que pode afetar a eficiência e confiabilidade dessas tecnologias. Além da irregularidade do terreno a inclinação, também, merece investigação cientifica para verificar as possíveis perturbações no processo de semeadura do milho. Objetivou-se avaliar a deposição de sementes de milho em inclinações longitudinais e transversais utilizando num dosador pneumático. O experimento foi realizado em bancada de semeadura estática, simulando as diferentes inclinações. Os resultados exibiram que a inclinação longitudinal não influenciou os espaçamentos aceitáveis das sementes, mas as variações transversais resultaram em maior incidência de espaçamentos indesejáveis. Conclui-se que a operação de semeadura quando realizada sob inclinação longitudinal resulta em diminuição da acurácia na deposição de sementes de milho, o que pode ser mitigado pelo cultivo em nível. Inclinações transversais apresentaram influência sobre os parâmetros de espaçamentos aceitáveis, duplos e falhos durante a semeadura.
- 1 January 2025
- Published by GN1 Sistemas e Publicacoes Ltd. in Revista Ciência Agronômica
- Vol. 56, 1-5
Open AccessEffect of pneumatic dosing mechanism angle on corn seed deposition
Maize sowing is essential for agricultural production and food security. Technological advances, such as electric pneumatic feeders and integrated software were developed with a view to economic and environmental sustainability. However, there are limitations in the knowledge of the physical phenomena related to sowing, which can affect the efficiency and reliability of these technologies. In addition to the terrain's irregularity, the slope also deserves scientific investigation to verify disturbances in the maize sowing process. The objective was to evaluate the deposition of corn seeds in longitudinal and transverse slopes using a pneumatic doser. The experiment was made on a static seeding bench, simulating the different inclinations. The results showed that the longitudinal inclination did not influence the acceptable spacing of the seeds, but the transverse variations resulted in a higher incidence of undesirable spacing. The study shown that the sowing operation when performed under longitudinal inclination results in a decrease in the accuracy of corn seed deposition, which can be mitigated by level cultivation. Transversal slopes influenced the parameters of acceptable, double and gap spacing during sowing. A semeadura de milho é essencial para a produção agrícola e segurança alimentar. Avanços tecnológicos, como dosadores pneumáticos elétricos e softwares integrados, têm sido desenvolvidos visando a sustentabilidade econômica e ambiental. No entanto, há limitações no conhecimento dos fenômenos físicos relacionados à semeadura, o que pode afetar a eficiência e confiabilidade dessas tecnologias. Além da irregularidade do terreno a inclinação, também, merece investigação cientifica para verificar as possíveis perturbações no processo de semeadura do milho. Objetivou-se avaliar a deposição de sementes de milho em inclinações longitudinais e transversais utilizando num dosador pneumático. O experimento foi realizado em bancada de semeadura estática, simulando as diferentes inclinações. Os resultados exibiram que a inclinação longitudinal não influenciou os espaçamentos aceitáveis das sementes, mas as variações transversais resultaram em maior incidência de espaçamentos indesejáveis. Conclui-se que a operação de semeadura quando realizada sob inclinação longitudinal resulta em diminuição da acurácia na deposição de sementes de milho, o que pode ser mitigado pelo cultivo em nível. Inclinações transversais apresentaram influência sobre os parâmetros de espaçamentos aceitáveis, duplos e falhos durante a semeadura.
- Open Access
- 1 January 2024
- Published by FapUNIFESP (SciELO) in Ciência Rural
- Vol. 54 (6) , e20220358
Distribution of granulated fertilizers in dispensers mounted with single and double helicoidal
The high dependence of agriculture on fertilizers demands an improvement in the processes involved, with the purpose of environmental and economic sustainability. The objective was to compare the performance of helical dosing mechanisms with two formulations of granulated NPK fertilizers at three operating speeds. During the experiment, we used an electronic and automated bench to evaluate the performance of the single helical and double helical dosing mechanisms, in a completely randomized design. This bench measured the overflow of the two formulations of granulated NPK fertilizers (04-14-08 and 04-30-10) under different angular velocities (1.11; 1.94; and 2.77 m s-1). On the tests, we collected flow data and submitted them to descriptive statistics, frequency histograms, and statistical process control. The single helical feeder, as the speed increased, exhibited greater homogeneity of granulated NPK fertilizer deposition, with 611 flaws ha-1 compared to 3763 flaws ha-1 in the double screw. Although, the speeds of 7.0 and 10.0 km h-1 generated an increase in the flow of both granular fertilizers, as expected, the 04-30-10 fertilizer obtained the most uniform distribution at the lowest speed.
- 1 January 2024
- Published by FapUNIFESP (SciELO) in Ciência Rural
- Vol. 54 (6) , e20220358
Open AccessDistribution of granulated fertilizers in dispensers mounted with single and double helicoidal
The high dependence of agriculture on fertilizers demands an improvement in the processes involved, with the purpose of environmental and economic sustainability. The objective was to compare the performance of helical dosing mechanisms with two formulations of granulated NPK fertilizers at three operating speeds. During the experiment, we used an electronic and automated bench to evaluate the performance of the single helical and double helical dosing mechanisms, in a completely randomized design. This bench measured the overflow of the two formulations of granulated NPK fertilizers (04-14-08 and 04-30-10) under different angular velocities (1.11; 1.94; and 2.77 m s-1). On the tests, we collected flow data and submitted them to descriptive statistics, frequency histograms, and statistical process control. The single helical feeder, as the speed increased, exhibited greater homogeneity of granulated NPK fertilizer deposition, with 611 flaws ha-1 compared to 3763 flaws ha-1 in the double screw. Although, the speeds of 7.0 and 10.0 km h-1 generated an increase in the flow of both granular fertilizers, as expected, the 04-30-10 fertilizer obtained the most uniform distribution at the lowest speed.
- Open Access
- 1 January 2024
- Published by FapUNIFESP (SciELO) in Ciência Rural
- Vol. 54 (3) , e20220186
Seed sensor position on seeder performance at varying speeds
The uniformity of seed distribution and sowing speed directly impact crop quality and productivity. This experiment assessed how the position of the sowing monitoring sensor influences the distribution of cotton seeds using a pneumatic meter at different operating speeds. The experiment employed a completely randomized two-factor factorial design on a static simulation bench. The first factor involved the sensor installation sites (upper, middle, and lower portions of the conductor tube and conveyor belt), while the second factor encompassed simulated speeds of 3.0, 5.0, 7.0, 9.0, and 11.0 km/h. Parameters such as frequency of double, flawed, and acceptable spacing, coefficient of variation, and precision index were measured based on five replications of 250 consecutive spacing. The results indicated that the sensor’s placement significantly influences reading accuracy. Optimal results were observed when the sensor was positioned at the final portion of the conductor tube, providing more accurate seed deposition, and facilitating decision-making.
- 1 January 2024
- Published by FapUNIFESP (SciELO) in Ciência Rural
- Vol. 54 (3) , e20220186
Open AccessSeed sensor position on seeder performance at varying speeds
The uniformity of seed distribution and sowing speed directly impact crop quality and productivity. This experiment assessed how the position of the sowing monitoring sensor influences the distribution of cotton seeds using a pneumatic meter at different operating speeds. The experiment employed a completely randomized two-factor factorial design on a static simulation bench. The first factor involved the sensor installation sites (upper, middle, and lower portions of the conductor tube and conveyor belt), while the second factor encompassed simulated speeds of 3.0, 5.0, 7.0, 9.0, and 11.0 km/h. Parameters such as frequency of double, flawed, and acceptable spacing, coefficient of variation, and precision index were measured based on five replications of 250 consecutive spacing. The results indicated that the sensor’s placement significantly influences reading accuracy. Optimal results were observed when the sensor was positioned at the final portion of the conductor tube, providing more accurate seed deposition, and facilitating decision-making.