Lauro Strapasson Neto
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Lauro Strapasson Neto has a total of 15 co-authors. Here are the top co-authors by number of shared publications:
- Leonardo Leonidas Kmiecik
Universidade Federal do Paraná, Brazil
9 shared publications - Samir Paulo Jasper
Universidade Federal do Paraná (UFPR), Brasil
8 shared publications - Daniel Savi
Universidade Federal do Paraná (UFPR), Brazil
7 shared publications - Gabriel Ganancini Zimmermann
Universidade Federal do Paraná (UFPR), Brasil
6 shared publications - Luiz Ricardo Sobenko
Universidade Federal do Paraná, Brazil
4 shared publications Daniel Savi
Universidade Federal do Paraná, Brasil
2 shared publications
Latest Publications
- Open Access
- 1 January 2023
- Published by FapUNIFESP (SciELO) in Anais da Academia Brasileira de Ciências
- Vol. 95 (3) , e20220312
Whole-plant corn silage harvesting modalities: energy efficiency and operational performance
The need for energy rationalizing in farming operations require research that optimize grain crop conduction. The operations used in the processing and production of silage have limitations in energy optimization due to the lack of studies. This paper evaluated energy efficiency of whole-plant silage operations with the objective of favor the decision making. The adopted design of the experiment was in parcels (with seven replications), consisting of three harvesting modalities: single-line forage harvester, total area forage harvester, and total area forage harvester with support transshipment. The tractors were instrumented with sensors that measured engine rotation, travel speed, and hourly fuel consumption which were used to calculate field capacity, fuel consumption per area and per harvested mass, and production capacity of the harvester-tractor set. The results went to analysis of variance and subsequently to Tukey’s test. The single had a faster speed and lower hourly fuel consumption, but smaller field capacity and greater energy expenditure for the mass. The use of support transshipment set with the front harvester allowed an improvement in the operation, with an increase in the worked area, and material processing (18%), and speed (13%), without differing in fuel expenditure. The total-area forage harvester modality showed smaller costs (USD 6.7), followed by the total-area forage harvester with support transshipment set (USD 7.7) and the single-line forage harvester (USD 9.38), respectively. The use of forage harvesters with a wider working width proved to be more efficient in terms of production costs per harvested hectare, validating it’s reccomendation.
- 1 January 2023
- Published by FapUNIFESP (SciELO) in Anais da Academia Brasileira de Ciências
- Vol. 95 (3) , e20220312
Open AccessWhole-plant corn silage harvesting modalities: energy efficiency and operational performance
The need for energy rationalizing in farming operations require research that optimize grain crop conduction. The operations used in the processing and production of silage have limitations in energy optimization due to the lack of studies. This paper evaluated energy efficiency of whole-plant silage operations with the objective of favor the decision making. The adopted design of the experiment was in parcels (with seven replications), consisting of three harvesting modalities: single-line forage harvester, total area forage harvester, and total area forage harvester with support transshipment. The tractors were instrumented with sensors that measured engine rotation, travel speed, and hourly fuel consumption which were used to calculate field capacity, fuel consumption per area and per harvested mass, and production capacity of the harvester-tractor set. The results went to analysis of variance and subsequently to Tukey’s test. The single had a faster speed and lower hourly fuel consumption, but smaller field capacity and greater energy expenditure for the mass. The use of support transshipment set with the front harvester allowed an improvement in the operation, with an increase in the worked area, and material processing (18%), and speed (13%), without differing in fuel expenditure. The total-area forage harvester modality showed smaller costs (USD 6.7), followed by the total-area forage harvester with support transshipment set (USD 7.7) and the single-line forage harvester (USD 9.38), respectively. The use of forage harvesters with a wider working width proved to be more efficient in terms of production costs per harvested hectare, validating it’s reccomendation.
- Open Access
- 1 January 2023
- Published by FapUNIFESP (SciELO) in Ciência Rural
- Vol. 53 (3)
Agricultural tractor with different mass distributions between axles
An adjustment of the agricultural tractor is necessary to achieve energy efficiency, which can be done through the correct distribution of mass between the axles for each operating surface. This research evaluated different distributions of mass between axles in a 93 kW tractor equipped with auxiliary front-wheel drive, on two soil surfaces. The experiment was carried out in strip design, with a double factorial scheme (2 x 3), with two soil surfaces (mobilized and firm) and three mass distributions between axes (35/65%, 40/60% and 45/55%), with five repetitions, totaling 30 parcels. The slippage parameters of the front and rear wheelset, engine rotation, hourly and specific fuel consumption, force, power and yield on the drawbar, displacement speed, engine thermal efficiency, traction coefficient, rolling resistance, and yield in traction. On firm soil, the energy performance of the tractor was superior in relation to the mobilized one, which allowed greater tractor and drawbar performance with lower specific fuel consumption. The use of a 35/65% between-axle mass distribution provided maximum traction for the mechanized set, resulting from the reduction in energy expenditure generated by skating and; consequently, the maximum use of the energy made available by the mechanized set. However, the maximum conversion of energy contained in the working fuel is obtained with the 45/55% setting.
- 1 January 2023
- Published by FapUNIFESP (SciELO) in Ciência Rural
- Vol. 53 (3)
Open AccessAgricultural tractor with different mass distributions between axles
An adjustment of the agricultural tractor is necessary to achieve energy efficiency, which can be done through the correct distribution of mass between the axles for each operating surface. This research evaluated different distributions of mass between axles in a 93 kW tractor equipped with auxiliary front-wheel drive, on two soil surfaces. The experiment was carried out in strip design, with a double factorial scheme (2 x 3), with two soil surfaces (mobilized and firm) and three mass distributions between axes (35/65%, 40/60% and 45/55%), with five repetitions, totaling 30 parcels. The slippage parameters of the front and rear wheelset, engine rotation, hourly and specific fuel consumption, force, power and yield on the drawbar, displacement speed, engine thermal efficiency, traction coefficient, rolling resistance, and yield in traction. On firm soil, the energy performance of the tractor was superior in relation to the mobilized one, which allowed greater tractor and drawbar performance with lower specific fuel consumption. The use of a 35/65% between-axle mass distribution provided maximum traction for the mechanized set, resulting from the reduction in energy expenditure generated by skating and; consequently, the maximum use of the energy made available by the mechanized set. However, the maximum conversion of energy contained in the working fuel is obtained with the 45/55% setting.
- Open Access
- 22 November 2022
- Published by Universidade Estadual de Maringa in Acta Scientiarum. Agronomy
- Vol. 45, e57920
Graphite action on the longitudinal distribution of soybean seeds in mechanical and pneumatic feeders
The use of powdered graphite as a solid lubricant to reduce friction among soybean seeds during mechanical sowing aims to facilitate the seed flow into the seed reservoir, while reducing mechanical damage to the seed. The objective of this study was to evaluate the influence of graphite on the longitudinal deposition of soybean seeds using mechanical and pneumatic feeders at different distribution velocities. The experiment was performed on a static simulation-test bench, with a completely randomized design with two varying factors: graphite dose (0, 1, 2, 4, and 8 g kg-1 seed) and distribution velocity (5, 7, 9, and 11 km h-1 for the pneumatic feeder; and 3, 5, 7, and 9 km h-1 for the mechanical feeder). To assess the homogeneity of seed distribution, the frequency of parameters such as double, flawed, and acceptable spacings, coefficient of variation, and precision index were evaluated from five repetitions of 250 spacing each. For the pneumatic feeder, the optimal values to maximize precision of seed deposition were 4.6 g kg-1 and 6.7 km h-1 of graphite dose and distribution velocity, respectively. In turn, the optimal values to minimize undesirable spacing while maximizing accuracy with the mechanical feeder were 4.9±0.6 g kg-1 and 4.9±0.3 km h-1. Overall, regardless of feeding mechanism, the use of graphite promoted greater efficiency in the distribution of seeds owing to the higher level of fluidity inside the reservoir; however, high doses can cause the opposite effect. In addition, an excessive increase in speed influenced seed distribution negatively.
- 22 November 2022
- Published by Universidade Estadual de Maringa in Acta Scientiarum. Agronomy
- Vol. 45, e57920
Open AccessGraphite action on the longitudinal distribution of soybean seeds in mechanical and pneumatic feeders
The use of powdered graphite as a solid lubricant to reduce friction among soybean seeds during mechanical sowing aims to facilitate the seed flow into the seed reservoir, while reducing mechanical damage to the seed. The objective of this study was to evaluate the influence of graphite on the longitudinal deposition of soybean seeds using mechanical and pneumatic feeders at different distribution velocities. The experiment was performed on a static simulation-test bench, with a completely randomized design with two varying factors: graphite dose (0, 1, 2, 4, and 8 g kg-1 seed) and distribution velocity (5, 7, 9, and 11 km h-1 for the pneumatic feeder; and 3, 5, 7, and 9 km h-1 for the mechanical feeder). To assess the homogeneity of seed distribution, the frequency of parameters such as double, flawed, and acceptable spacings, coefficient of variation, and precision index were evaluated from five repetitions of 250 spacing each. For the pneumatic feeder, the optimal values to maximize precision of seed deposition were 4.6 g kg-1 and 6.7 km h-1 of graphite dose and distribution velocity, respectively. In turn, the optimal values to minimize undesirable spacing while maximizing accuracy with the mechanical feeder were 4.9±0.6 g kg-1 and 4.9±0.3 km h-1. Overall, regardless of feeding mechanism, the use of graphite promoted greater efficiency in the distribution of seeds owing to the higher level of fluidity inside the reservoir; however, high doses can cause the opposite effect. In addition, an excessive increase in speed influenced seed distribution negatively.
- Open Access
- 1 May 2022
- Published by FapUNIFESP (SciELO) in Revista Brasileira de Engenharia Agrícola E Ambiental
- Vol. 26 (5) , 356-364
Energy performance of farm tractor with single radial versus dual diagonal wheels in harrowing operations
The farm tractor wheel interacts directly with the soil, affecting its energy and operational performance. Several works study the particularities between configurations of wheelset seeking to interpret the most efficient type and arrangement of the wheelset. However, there is still a demand for studies that elucidate decision-making regarding changing the type of wheelset or improving the pre-existing arrangement. The experiment aimed to evaluate the energy performance of farm tractors equipped with Single radial and Dual diagonal wheels in rear axle in intermediate harrowing operation. The experiment was conducted in a randomized block design. Two-wheel arrangements (Single radial and Dual diagonal) were used in the blocks, and four target velocities (4, 6, 8, and 10 km h-1), with four replicates in the subblocks, totalizing 32 experimental units. Slip of wheels, engine rotation, hourly and specific fuel consumption, force, power, and efficiency in the drawbar, operational velocity, and engine thermal efficiency were monitored. The data collected were submitted to analysis of variance and, when significant, to the Tukey test and regression analysis. The Single radial tires provided an increase in velocity and drawbar force without increasing fuel consumption, consequently providing an increase in energy and operating performance in intermediate harrowing operation.
- 1 May 2022
- Published by FapUNIFESP (SciELO) in Revista Brasileira de Engenharia Agrícola E Ambiental
- Vol. 26 (5) , 356-364
Open AccessEnergy performance of farm tractor with single radial versus dual diagonal wheels in harrowing operations
The farm tractor wheel interacts directly with the soil, affecting its energy and operational performance. Several works study the particularities between configurations of wheelset seeking to interpret the most efficient type and arrangement of the wheelset. However, there is still a demand for studies that elucidate decision-making regarding changing the type of wheelset or improving the pre-existing arrangement. The experiment aimed to evaluate the energy performance of farm tractors equipped with Single radial and Dual diagonal wheels in rear axle in intermediate harrowing operation. The experiment was conducted in a randomized block design. Two-wheel arrangements (Single radial and Dual diagonal) were used in the blocks, and four target velocities (4, 6, 8, and 10 km h-1), with four replicates in the subblocks, totalizing 32 experimental units. Slip of wheels, engine rotation, hourly and specific fuel consumption, force, power, and efficiency in the drawbar, operational velocity, and engine thermal efficiency were monitored. The data collected were submitted to analysis of variance and, when significant, to the Tukey test and regression analysis. The Single radial tires provided an increase in velocity and drawbar force without increasing fuel consumption, consequently providing an increase in energy and operating performance in intermediate harrowing operation.
- Open Access
- 1 March 2022
- Published by FapUNIFESP (SciELO) in Revista Brasileira de Engenharia Agrícola E Ambiental
- Vol. 26 (3) , 226-235
Fertilizer deposition as a function of angular velocity and inclination of the helical dosing mechanism
The establishment of grain crops in Brazil is an important industrial process in the agricultural chain, requiring the correct deposition of granular fertilizer over the sowing furrow and more efficient, precise, and sustainable assessments in the operation, which can be achieved with the statistical process control. This study aimed to assess the effect of the angular velocity on different inclinations of the helical metering mechanism on the granular fertilizer deposition. An automated electronic bench was used to assess the deposition quality of granular fertilizers considering different angular velocities (1.11, 1.94, and 2.77 m s-1) and longitudinal and transverse inclinations (+15, +7.5, 0, −7.5, and −15°), with the helical doser by overflow. Flow data were collected and submitted to descriptive statistics and statistical process control. The metering mechanism showed expected variations, with acceptable performance under process control. The values of the flow rates of the granular fertilizer increased as velocity increased, standing out longitudinal inclinations of +7.5 and +15°, providing higher fertilizer depositions.
- 1 March 2022
- Published by FapUNIFESP (SciELO) in Revista Brasileira de Engenharia Agrícola E Ambiental
- Vol. 26 (3) , 226-235
Open AccessFertilizer deposition as a function of angular velocity and inclination of the helical dosing mechanism
The establishment of grain crops in Brazil is an important industrial process in the agricultural chain, requiring the correct deposition of granular fertilizer over the sowing furrow and more efficient, precise, and sustainable assessments in the operation, which can be achieved with the statistical process control. This study aimed to assess the effect of the angular velocity on different inclinations of the helical metering mechanism on the granular fertilizer deposition. An automated electronic bench was used to assess the deposition quality of granular fertilizers considering different angular velocities (1.11, 1.94, and 2.77 m s-1) and longitudinal and transverse inclinations (+15, +7.5, 0, −7.5, and −15°), with the helical doser by overflow. Flow data were collected and submitted to descriptive statistics and statistical process control. The metering mechanism showed expected variations, with acceptable performance under process control. The values of the flow rates of the granular fertilizer increased as velocity increased, standing out longitudinal inclinations of +7.5 and +15°, providing higher fertilizer depositions.
- Open Access
- 1 July 2021
- Published by FapUNIFESP (SciELO) in Revista Brasileira de Engenharia Agrícola E Ambiental
- Vol. 25 (7) , 498-502
Performance of agricultural tractor with and without automatic transmission and engine rotation management
HIGHLIGHTS Electronic gear selection and autonomous engine rotation management bring benefits to tractor driving. The electronic management responded positively to the increase in the traction load. The use of electronic management software should be more widespread among farmers and researchers.
- 1 July 2021
- Published by FapUNIFESP (SciELO) in Revista Brasileira de Engenharia Agrícola E Ambiental
- Vol. 25 (7) , 498-502
Open AccessPerformance of agricultural tractor with and without automatic transmission and engine rotation management
HIGHLIGHTS Electronic gear selection and autonomous engine rotation management bring benefits to tractor driving. The electronic management responded positively to the increase in the traction load. The use of electronic management software should be more widespread among farmers and researchers.
- Open Access
- 1 April 2021
- Published by FapUNIFESP (SciELO) in Revista Brasileira de Engenharia Agrícola E Ambiental
- Vol. 25 (4) , 277-281
Agricultural tractor traction efficiency by changing the mass distribution between axles and speed
The traction efficiency of the agricultural tractor can be maximized by adjusting the total mass and its distribution between the axles. The experiment’s objective was to determine the configuration of mass distribution between axles and the displacement speed that provides greater traction efficiency in the harrowing operation. A randomized block design in a 2 × 3 factorial scheme with five replications was used. The first factor was two mass distributions between axles, and the second factor was three gears. The collected data were submitted to analysis of variance and the Tukey test. The condition that maximizes the tractor’s performance corresponds to 39% of the total mass on the front axle and 61% on the rear axle, with a gear that provides speed close to 10 km h-1.
- 1 April 2021
- Published by FapUNIFESP (SciELO) in Revista Brasileira de Engenharia Agrícola E Ambiental
- Vol. 25 (4) , 277-281
Open AccessAgricultural tractor traction efficiency by changing the mass distribution between axles and speed
The traction efficiency of the agricultural tractor can be maximized by adjusting the total mass and its distribution between the axles. The experiment’s objective was to determine the configuration of mass distribution between axles and the displacement speed that provides greater traction efficiency in the harrowing operation. A randomized block design in a 2 × 3 factorial scheme with five replications was used. The first factor was two mass distributions between axles, and the second factor was three gears. The collected data were submitted to analysis of variance and the Tukey test. The condition that maximizes the tractor’s performance corresponds to 39% of the total mass on the front axle and 61% on the rear axle, with a gear that provides speed close to 10 km h-1.
- Open Access
- 1 January 2021
- Published by FapUNIFESP (SciELO) in Ciência E Agrotecnologia
- Vol. 45
Operational performance and energy efficiency of axial harvesters with single and double rotor systems in soybean seed harvest
The decision-making capability of the machine to harvest grains must consider a lower fuel consumption with a higher operating velocity allied to a greater performance of the grain cleaning system, along with lower rates of the damage and waste produced. This study aimed at evaluating the operational performance and the energy efficiency of two axial harvesters, having different trail and separation systems in the soybean seed harvest. The experiment was carried out in a completely randomized block design in 500-m bands, consisting of two factors, namely two axial harvesters (single and double rotor) and six target velocities (3, 4, 5, 6, 7, and 8 km h-1). Regarding the operational energy performance, the hourly fuel consumption, operational speed, operational field capacity, fuel consumption per area and mass of the harvested grain, and the handling capacity of the harvest were evaluated. The harvesting performance parameters, such as the percentage losses in the platform and the trail system, broken grains, impurities, and the pods, which did not undergo threshing, were evaluated. The results obtained showed that the single-rotor harvester had a better energy efficiency, while the double-rotor harvester had a better operational performance. The double-rotor harvester was agronomically more efficient.
- 1 January 2021
- Published by FapUNIFESP (SciELO) in Ciência E Agrotecnologia
- Vol. 45
Open AccessOperational performance and energy efficiency of axial harvesters with single and double rotor systems in soybean seed harvest
The decision-making capability of the machine to harvest grains must consider a lower fuel consumption with a higher operating velocity allied to a greater performance of the grain cleaning system, along with lower rates of the damage and waste produced. This study aimed at evaluating the operational performance and the energy efficiency of two axial harvesters, having different trail and separation systems in the soybean seed harvest. The experiment was carried out in a completely randomized block design in 500-m bands, consisting of two factors, namely two axial harvesters (single and double rotor) and six target velocities (3, 4, 5, 6, 7, and 8 km h-1). Regarding the operational energy performance, the hourly fuel consumption, operational speed, operational field capacity, fuel consumption per area and mass of the harvested grain, and the handling capacity of the harvest were evaluated. The harvesting performance parameters, such as the percentage losses in the platform and the trail system, broken grains, impurities, and the pods, which did not undergo threshing, were evaluated. The results obtained showed that the single-rotor harvester had a better energy efficiency, while the double-rotor harvester had a better operational performance. The double-rotor harvester was agronomically more efficient.
- Open Access
- 1 October 2020
- Published by FapUNIFESP (SciELO) in Engenharia Agrícola
- Vol. 40 (5) , 617-623
OPERATIONAL AND ENERGY PERFORMANCE OF 250 kW DOUBLE WHEELED VERSUS RUBBER HALF-TRACKED TRACTORS IN THE SOYBEAN SOWING
The technological innovation in agriculture seeks to improve the performance of mechanized assemblies and, currently, rubber half-tracks are a valuable solution for agricultural tractors, combining traction performance and less soil compaction. The objective of the experiment was to evaluate the operational and energy performance of double wheeled versus rubber half-tracked agricultural tractors in the soybean sowing. The experiment was conducted in a strip-plot design with a double factorial arrangement (2×3). The first factor consisted of a tractor with double wheels on the front and rear axles versus a tractor with single wheels on the front axle and rubber half-tracks on the rear axle, while the second factor consisted of three different gears, with five replications, totaling 30 experimental units. The collected data were subjected to analysis of variance and, when significant, to the Tukey test. The sowing operation carried out with the half-tracked tractor was the most efficient in most of the analyzed parameters, allowing higher operational and energy efficiency in the soybean sowing.
- 1 October 2020
- Published by FapUNIFESP (SciELO) in Engenharia Agrícola
- Vol. 40 (5) , 617-623
Open AccessOPERATIONAL AND ENERGY PERFORMANCE OF 250 kW DOUBLE WHEELED VERSUS RUBBER HALF-TRACKED TRACTORS IN THE SOYBEAN SOWING
The technological innovation in agriculture seeks to improve the performance of mechanized assemblies and, currently, rubber half-tracks are a valuable solution for agricultural tractors, combining traction performance and less soil compaction. The objective of the experiment was to evaluate the operational and energy performance of double wheeled versus rubber half-tracked agricultural tractors in the soybean sowing. The experiment was conducted in a strip-plot design with a double factorial arrangement (2×3). The first factor consisted of a tractor with double wheels on the front and rear axles versus a tractor with single wheels on the front axle and rubber half-tracks on the rear axle, while the second factor consisted of three different gears, with five replications, totaling 30 experimental units. The collected data were subjected to analysis of variance and, when significant, to the Tukey test. The sowing operation carried out with the half-tracked tractor was the most efficient in most of the analyzed parameters, allowing higher operational and energy efficiency in the soybean sowing.
- Open Access
- 1 June 2020
- Published by FapUNIFESP (SciELO) in Engenharia Agrícola
- Vol. 40 (3) , 356-362
INTERFERENCE OF THE NUMBER OF REMOTE CONTROL VALVES IN USE ON THE ENERGY PERFORMANCE OF AN AGRICULTURAL TRACTOR WITH PRODUCTIVITY MANAGEMENT
- 1 June 2020
- Published by FapUNIFESP (SciELO) in Engenharia Agrícola
- Vol. 40 (3) , 356-362
Open AccessINTERFERENCE OF THE NUMBER OF REMOTE CONTROL VALVES IN USE ON THE ENERGY PERFORMANCE OF AN AGRICULTURAL TRACTOR WITH PRODUCTIVITY MANAGEMENT