Julio Carrero-Blanco
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Julio Carrero-Blanco has a total of 7 co-authors. Here are the top co-authors by number of shared publications:
Manuel Estrems
Mechanical Materials and Manufacturing Engineering Department Universidad Politécnica de Cartagena 30202 Cartagena Spain
2 shared publications- Manuel Estrems
Universidad Politécnica de Cartagena
2 shared publications Wilmer E. Cumbicus
Mechanical Materials and Manufacturing Engineering Department Universidad Politécnica de Cartagena 30202 Cartagena Spain
2 shared publications- Óscar de Francisco Ortiz
Technical University of Cartagena
2 shared publications Gabriel Ros
Mechanical Materials and Manufacturing Engineering Department Universidad Politécnica de Cartagena 30202 Cartagena Spain
1 shared publication- Horacio T. Sánchez
Mechanics, Materials and iManufacturing Engineering department, Technical University of Cartagena, 30202 Cartagena, Spain
1 shared publication
Latest Publications
- Open Access
- 25 August 2025
- Published by Springer Nature in Research Square
Machining of Turbine Blade designed by NURBS on a 5-Axis Milling Machine
This communication presents the design, modeling and machining in 5 axis of a turbine blade. It is modelled using the NURBS technique that approximates a NASA Rotor R67 profile. From the CAD design, certain characteristics have been extracted to proceed to its machining in a 5-axis milling machine. For generating the trajectories on the surface, a layered discretization technique was used on which the sequence of points and orientations of the spherical cutter were generated, which deals on the optimal orientation control of tools in 5 axes. After generating the G-code corresponding to the finishing process, the method was tested with a LAGUN-650 machining center with an additional 2-axis rotary table, on a prefabricated part by FDM. The result, presented in this work shows the validity of the methodology to machine blade surfaces with high surface finishing requirements.
- 25 August 2025
- Published by Springer Nature in Research Square
Open AccessMachining of Turbine Blade designed by NURBS on a 5-Axis Milling Machine
This communication presents the design, modeling and machining in 5 axis of a turbine blade. It is modelled using the NURBS technique that approximates a NASA Rotor R67 profile. From the CAD design, certain characteristics have been extracted to proceed to its machining in a 5-axis milling machine. For generating the trajectories on the surface, a layered discretization technique was used on which the sequence of points and orientations of the spherical cutter were generated, which deals on the optimal orientation control of tools in 5 axes. After generating the G-code corresponding to the finishing process, the method was tested with a LAGUN-650 machining center with an additional 2-axis rotary table, on a prefabricated part by FDM. The result, presented in this work shows the validity of the methodology to machine blade surfaces with high surface finishing requirements.
- Open Access
- 4 July 2025
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 139 (5-6) , 2307-2325
Influence of the contact pressure distribution in boring machining of two coupled part components
Two coupled part components such as bearings or connecting rods have a wide application in mechanical systems. The performance, efficiency, and durability of these components depend on the tolerances and surface quality obtained after being manufactured. One of the main problems that two coupled part components usually present is the appearance of discontinuities in their union interface, affecting the machining that will be performed in their interior housing once the assembly is carried out. In this work, the effect of pressure distribution for different tightening torque values applied in the two coupled part elements is studied, using the finite element method with non-linear contact elements and a matrix method of simplifying the model based in deformation energy. The latter is based on obtaining the distribution of contact forces through the conditions of Kuhn-Tücker and the method of Lagrange multipliers, which allows knowing what effects occur in the contact area. Subsequently, an experimental boring study has been carried out where the cutting forces are measured and the power spectrum is analyzed to determine if there are disturbances that can affect the roundness and quality surface of the manufactured component, and consequently, to a possible anomalous operation of the mechanical system in which the bi-components will be mounted.
- 4 July 2025
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 139 (5-6) , 2307-2325
Open AccessInfluence of the contact pressure distribution in boring machining of two coupled part components
Two coupled part components such as bearings or connecting rods have a wide application in mechanical systems. The performance, efficiency, and durability of these components depend on the tolerances and surface quality obtained after being manufactured. One of the main problems that two coupled part components usually present is the appearance of discontinuities in their union interface, affecting the machining that will be performed in their interior housing once the assembly is carried out. In this work, the effect of pressure distribution for different tightening torque values applied in the two coupled part elements is studied, using the finite element method with non-linear contact elements and a matrix method of simplifying the model based in deformation energy. The latter is based on obtaining the distribution of contact forces through the conditions of Kuhn-Tücker and the method of Lagrange multipliers, which allows knowing what effects occur in the contact area. Subsequently, an experimental boring study has been carried out where the cutting forces are measured and the power spectrum is analyzed to determine if there are disturbances that can affect the roundness and quality surface of the manufactured component, and consequently, to a possible anomalous operation of the mechanical system in which the bi-components will be mounted.
- Open Access
- 30 June 2020
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 109 (1-2) , 155-170
Positioning measurement using a new artificial vision algorithm in LabVIEW based on the analysis of images on an LCD screen
- 30 June 2020
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 109 (1-2) , 155-170
Open AccessPositioning measurement using a new artificial vision algorithm in LabVIEW based on the analysis of images on an LCD screen
- Open Access
Enhanced Positioning Algorithm Using a Single Image in an LCD-Camera System by Mesh Elements’ Recalculation and Angle Error Orientation
In this article, we present a method to position the tool in a micromachine system based on a camera-LCD screen positioning system that also provides information about angular deviations of the tool axis during its running. Both position and angular deviations are obtained by reducing a matrix of LEDs in the image to a single rectangle in the conical perspective that is treated by a photogrammetry method. This method computes the coordinates and orientation of the camera with respect to the fixed screen coordinate system. The used image consists of 5 × 5 lit LEDs, which are analyzed by the algorithm to determine a rectangle with known dimensions. The coordinates of the vertices of the rectangle in space are obtained by an inverse perspective computation from the image. The method presents a good approximation of the central point of the rectangle and provides the inclination of the workpiece with respect to the LCD screen reference system of coordinates. A test of the method is designed with the assistance of a Coordinate Measurement Machine (CMM) to check the accuracy of the positioning method. The performed test delivers a good accuracy in the position measurement of the designed method. A high dispersion in the angular deviation is detected, although the orientation of the inclination is appropriate in almost every case. This is due to the small values of the angles that makes the trigonometric function approximations very erratic. This method is a good starting point for the compensation of angular deviation in vision based micromachine tools, which is the principal source of errors in these operations and represents the main volume in the cost of machine elements’ parts.
Open AccessEnhanced Positioning Algorithm Using a Single Image in an LCD-Camera System by Mesh Elements’ Recalculation and Angle Error Orientation
In this article, we present a method to position the tool in a micromachine system based on a camera-LCD screen positioning system that also provides information about angular deviations of the tool axis during its running. Both position and angular deviations are obtained by reducing a matrix of LEDs in the image to a single rectangle in the conical perspective that is treated by a photogrammetry method. This method computes the coordinates and orientation of the camera with respect to the fixed screen coordinate system. The used image consists of 5 × 5 lit LEDs, which are analyzed by the algorithm to determine a rectangle with known dimensions. The coordinates of the vertices of the rectangle in space are obtained by an inverse perspective computation from the image. The method presents a good approximation of the central point of the rectangle and provides the inclination of the workpiece with respect to the LCD screen reference system of coordinates. A test of the method is designed with the assistance of a Coordinate Measurement Machine (CMM) to check the accuracy of the positioning method. The performed test delivers a good accuracy in the position measurement of the designed method. A high dispersion in the angular deviation is detected, although the orientation of the inclination is appropriate in almost every case. This is due to the small values of the angles that makes the trigonometric function approximations very erratic. This method is a good starting point for the compensation of angular deviation in vision based micromachine tools, which is the principal source of errors in these operations and represents the main volume in the cost of machine elements’ parts.