Federico Ventosinos
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Federico Ventosinos has a total of 45 co-authors. Here are the top co-authors by number of shared publications:
- Javier Alejandro Schmidt
Instituto de Física del Litoral (IFIS-Litoral), CONICET-UNL 1 , Güemes 3450, S3000GLN Santa Fe, Argentina
5 shared publications - Henk J. Bolink
Universidad de Valencia C/Catedrático J. Beltrán 2
4 shared publications - Daniel Pérez-Del-Rey
Instituto de Ciencia Molecular, Universidad de Valencia 3 , C/Catedrático J. Beltrán 2, 46980 Paterna, Spain
3 shared publications - Jorge Caram
Centro de Investigación de Métodos Computacionales (CIMEC
3 shared publications - Anderzon F. Palechor-Ocampo
Instituto de Física del Litoral (IFIS-Litoral) CONICET-UNL Güemes 3450 S3000GLN Santa Fe Argentina
2 shared publications - Maximiliano Senno
Universidad de Valencia
2 shared publications
Latest Publications
- Open Access
- 16 June 2026
- Published by American Physical Society (APS) in PRX Energy
- Vol. 5 (3)
Red, white & blue: Identifying recombination loss mechanisms in perovskite solar cells
Photovoltaics play a key role in the renewable energy transition, where perovskite solar cells stand out as one of the most promising with high-power conversion efficiencies, desirable characteristics, and great versatility. The efficiency of these cells is mainly limited by nonradiative recombination, whether at one of the interfaces between the perovskite layer and transport layers or within the bulk of the perovskite itself. However, it is difficult to probe which of these dominates the losses during operation, which complicates further improvements. Here we introduce and demonstrate a simple, inexpensive, and easy-to-integrate method for identification of the limiting aspect of perovskite solar cells under operating conditions in terms of recombination losses. We illuminate a device with red, blue, or white light, each absorbed differently depending on the position in the device. We show that, in perovskite solar cells, the diffusion length in the bulk is of secondary importance and rather the interfaces between layers dominate the charge carrier distributions, and thus light of different wavelengths will result in changing performance. Using the fill factor from the device characteristics for each case, we are able to identify whether the front or back interface of the cell limits the performance with nearly 97% accuracy. Finally, we apply this principle experimentally using a co-evaporated perovskite solar cell, where we show a decrease of nearly 5% in fill factor depending on the wavelength of light used.
- 16 June 2026
- Published by American Physical Society (APS) in PRX Energy
- Vol. 5 (3)
Open AccessRed, white & blue: Identifying recombination loss mechanisms in perovskite solar cells
Photovoltaics play a key role in the renewable energy transition, where perovskite solar cells stand out as one of the most promising with high-power conversion efficiencies, desirable characteristics, and great versatility. The efficiency of these cells is mainly limited by nonradiative recombination, whether at one of the interfaces between the perovskite layer and transport layers or within the bulk of the perovskite itself. However, it is difficult to probe which of these dominates the losses during operation, which complicates further improvements. Here we introduce and demonstrate a simple, inexpensive, and easy-to-integrate method for identification of the limiting aspect of perovskite solar cells under operating conditions in terms of recombination losses. We illuminate a device with red, blue, or white light, each absorbed differently depending on the position in the device. We show that, in perovskite solar cells, the diffusion length in the bulk is of secondary importance and rather the interfaces between layers dominate the charge carrier distributions, and thus light of different wavelengths will result in changing performance. Using the fill factor from the device characteristics for each case, we are able to identify whether the front or back interface of the cell limits the performance with nearly 97% accuracy. Finally, we apply this principle experimentally using a co-evaporated perovskite solar cell, where we show a decrease of nearly 5% in fill factor depending on the wavelength of light used.
- Open Access
- 19 May 2026
- Published by Springer Nature in Nature Energy
- Vol. 11 (7) , 1078-1089
Close-space sublimation as a versatile deposition process for efficient perovskite silicon tandem solar cells
The envisaged breakthrough of perovskite photovoltaic technologies demands rapid advances in scalable and robust high-throughput fabrication methods. Here we present close-space sublimation (CSS) as a vacuum-based, industrially relevant deposition method for the conversion of sublimed PbI 2 inorganic scaffolds into high-quality wide-bandgap perovskite absorbers (MAPb(I 0.79 Br 0.21 ) 3 , 1.64 eV), employing a reusable mixed-halide organic source for stable bandgap control. We provide mechanistic insights into the substitution-reaction-limited CSS process and achieve power conversion efficiencies (PCEs) of up to 18.5% for fully vacuum-processed p–i–n single-junction devices. Monolithic integration in tandem solar cells onto planar, nano- and micro-textured silicon bottom cells reveals consistent optoelectronic and morphological properties across all configurations without requiring adjustments of deposition parameters, as corroborated by comprehensive characterization techniques. The resulting perovskite/silicon tandem solar cells reach PCEs up to 24.3%, with minimal variation across the different bottom cells. Our findings highlight the broad process window and versatility of CSS, positioning it as an industry-suitable deposition method for solvent-free high-throughput fabrication.
- 19 May 2026
- Published by Springer Nature in Nature Energy
- Vol. 11 (7) , 1078-1089
Open AccessClose-space sublimation as a versatile deposition process for efficient perovskite silicon tandem solar cells
The envisaged breakthrough of perovskite photovoltaic technologies demands rapid advances in scalable and robust high-throughput fabrication methods. Here we present close-space sublimation (CSS) as a vacuum-based, industrially relevant deposition method for the conversion of sublimed PbI 2 inorganic scaffolds into high-quality wide-bandgap perovskite absorbers (MAPb(I 0.79 Br 0.21 ) 3 , 1.64 eV), employing a reusable mixed-halide organic source for stable bandgap control. We provide mechanistic insights into the substitution-reaction-limited CSS process and achieve power conversion efficiencies (PCEs) of up to 18.5% for fully vacuum-processed p–i–n single-junction devices. Monolithic integration in tandem solar cells onto planar, nano- and micro-textured silicon bottom cells reveals consistent optoelectronic and morphological properties across all configurations without requiring adjustments of deposition parameters, as corroborated by comprehensive characterization techniques. The resulting perovskite/silicon tandem solar cells reach PCEs up to 24.3%, with minimal variation across the different bottom cells. Our findings highlight the broad process window and versatility of CSS, positioning it as an industry-suitable deposition method for solvent-free high-throughput fabrication.
- 24 November 2025
- Published by IOP Publishing in Journal of Physics D: Applied Physics
- Vol. 58 (47) , 475109
Ion transport and defect states within the band gap of lead halide perovskites studied via the moving grating technique
Ion migration is a distinctive feature and the primary cause of instability in metal halide perovskites (MHPs) used in photovoltaics. Among the various methods developed to study the electrical transport properties of MHPs, the Moving Grating Technique (MGT) has emerged as a valuable tool to obtain insights into ion mobility. In this technique, a photoconductor is illuminated with a moving interference pattern, inducing a direct current that reaches a maximum when the grating velocity matches the moving velocity of the charge carriers. In MHPs, it has been found that the induced current exhibits a low-velocity peak related to ion movement, alongside the free carrier’s peak. In this work, we use the MGT to study ion migration in perovskite thin films, supporting our findings with a detailed theoretical model incorporating the material’s density of states and recombination mechanisms. Our MGT measurements on FA 0.8 Cs 0.2 Pb(I 0.9 Br 0.1 ) 3 reveal three characteristic peaks: a high-frequency positive peak for free carriers, a broad negative peak attributed to ions, and a novel positive low-frequency peak. The detailed model successfully reproduces the novel positive low-frequency peak by including a donor defect state near the conduction band edge. On the other hand, measurements and simulations on standard MAPbI 3 thin films show the typical high-frequency free carrier peak and a broad negative ion peak, but lack the low-frequency positive peak, supporting the conclusion that this peak is linked to the specific donor defect state in the FA 0.8 Cs 0.2 Pb(I 0.9 Br 0.1 ) 3 material.
- 24 November 2025
- Published by IOP Publishing in Journal of Physics D: Applied Physics
- Vol. 58 (47) , 475109
Ion transport and defect states within the band gap of lead halide perovskites studied via the moving grating technique
Ion migration is a distinctive feature and the primary cause of instability in metal halide perovskites (MHPs) used in photovoltaics. Among the various methods developed to study the electrical transport properties of MHPs, the Moving Grating Technique (MGT) has emerged as a valuable tool to obtain insights into ion mobility. In this technique, a photoconductor is illuminated with a moving interference pattern, inducing a direct current that reaches a maximum when the grating velocity matches the moving velocity of the charge carriers. In MHPs, it has been found that the induced current exhibits a low-velocity peak related to ion movement, alongside the free carrier’s peak. In this work, we use the MGT to study ion migration in perovskite thin films, supporting our findings with a detailed theoretical model incorporating the material’s density of states and recombination mechanisms. Our MGT measurements on FA 0.8 Cs 0.2 Pb(I 0.9 Br 0.1 ) 3 reveal three characteristic peaks: a high-frequency positive peak for free carriers, a broad negative peak attributed to ions, and a novel positive low-frequency peak. The detailed model successfully reproduces the novel positive low-frequency peak by including a donor defect state near the conduction band edge. On the other hand, measurements and simulations on standard MAPbI 3 thin films show the typical high-frequency free carrier peak and a broad negative ion peak, but lack the low-frequency positive peak, supporting the conclusion that this peak is linked to the specific donor defect state in the FA 0.8 Cs 0.2 Pb(I 0.9 Br 0.1 ) 3 material.
- 6 January 2023
- Published by Wiley in Energy Technology
- Vol. 11 (3)
Singular Time‐Dependent Photoconductivity Response of MAPbI3 Samples Deposited by Vacuum Processing on Different Substrates
Organo–inorganic halide perovskites continue to generate enormous interest for their potential use in various optoelectronic devices. Among the different fabrication methods, vacuum thermal deposition allows uniform films over large areas, providing good material quality without using organic solvents. However, the influence of the substrate on the properties of the material deposited by vacuum processing is a point that deserves further investigation. Herein, time‐dependent photoconductivity measurements are used to investigate the dynamics of charge carriers under illumination in planar films of CH3NH3PbI3. The samples are deposited by thermal sublimation on different substrates: PbI2, TaTm, C60, and glass. Experimentally, it is shown that the substrate has a profound effect on perovskite behavior and that photoconductivity is sensitive enough to probe these behaviors. Furthermore, a model based on Shockley–Read–Hall statistics is proposed, explaining the different photoconductivity responses by changing only the relative values of the different capture coefficients and the position of the Fermi level. It is argued that the substrate changes the stoichiometry of the evaporated material, affecting the transient photoconductivity response.
- 6 January 2023
- Published by Wiley in Energy Technology
- Vol. 11 (3)
Singular Time‐Dependent Photoconductivity Response of MAPbI3 Samples Deposited by Vacuum Processing on Different Substrates
Organo–inorganic halide perovskites continue to generate enormous interest for their potential use in various optoelectronic devices. Among the different fabrication methods, vacuum thermal deposition allows uniform films over large areas, providing good material quality without using organic solvents. However, the influence of the substrate on the properties of the material deposited by vacuum processing is a point that deserves further investigation. Herein, time‐dependent photoconductivity measurements are used to investigate the dynamics of charge carriers under illumination in planar films of CH3NH3PbI3. The samples are deposited by thermal sublimation on different substrates: PbI2, TaTm, C60, and glass. Experimentally, it is shown that the substrate has a profound effect on perovskite behavior and that photoconductivity is sensitive enough to probe these behaviors. Furthermore, a model based on Shockley–Read–Hall statistics is proposed, explaining the different photoconductivity responses by changing only the relative values of the different capture coefficients and the position of the Fermi level. It is argued that the substrate changes the stoichiometry of the evaporated material, affecting the transient photoconductivity response.
- 21 March 2022
- Published by AIP Publishing in The Journal of Chemical Physics
- Vol. 156 (11) , 114201
Density of states within the bandgap of perovskite thin films studied using the moving grating technique
In this work, we further study the moving grating technique applied to halide perovskite thin-film materials. First, we show some problems that emerge when analyzing the experimental data with the classical formulation, which does not distinguish between free and trapped carriers and hence only gives average quantities for the transport parameters. We show that using a more general framework, taking into account the multiple trapping of carriers within a density of localized states, allows for an accurate description. Since it includes the density of states (DOS) of the material, it enables the possibility to test different DOS models proposed in the past for halide perovskite thin films. We check whether these models give rise to the type of curves we have measured under different experimental conditions. Finally, we propose a new model for the DOS in the forbidden gap, which results in the best fit found for the measurements performed. This allows us to give ranges of values for the parameters that define the DOS, which, as far as we know, are given for the first time.
- 21 March 2022
- Published by AIP Publishing in The Journal of Chemical Physics
- Vol. 156 (11) , 114201
Density of states within the bandgap of perovskite thin films studied using the moving grating technique
In this work, we further study the moving grating technique applied to halide perovskite thin-film materials. First, we show some problems that emerge when analyzing the experimental data with the classical formulation, which does not distinguish between free and trapped carriers and hence only gives average quantities for the transport parameters. We show that using a more general framework, taking into account the multiple trapping of carriers within a density of localized states, allows for an accurate description. Since it includes the density of states (DOS) of the material, it enables the possibility to test different DOS models proposed in the past for halide perovskite thin films. We check whether these models give rise to the type of curves we have measured under different experimental conditions. Finally, we propose a new model for the DOS in the forbidden gap, which results in the best fit found for the measurements performed. This allows us to give ranges of values for the parameters that define the DOS, which, as far as we know, are given for the first time.
- 21 July 2020
- Published by IOP Publishing in Journal of Physics D: Applied Physics
- Vol. 53 (41) , 415107
Estimation of carrier mobilities and recombination lifetime in halide perovskites films using the moving grating technique
Pulsed excitation methods followed by time-resolved measurements have been questioned as a valid procedure to deduce transport properties of halide perovskites (HaPs). Measurements of both the majority and minority carrier’s phototransport properties, under illumination conditions as close as possible to one sun, are needed to obtain reliable information on recombination mechanisms. In this work, we show that the moving photocarrier grating technique (MGT) fulfills the above-mentioned conditions. In this method, both carriers mobilities and the common recombination lifetime are deduced from the DC short circuit current induced by the movement of an interference pattern along the sample surface. We show that the method, originally developed to measure the transport parameters of amorphous semiconductors, can be fully applied to HaPs films. We briefly describe the technique, we perform measurements as a function of the grating period and the light intensity, and we discuss the best approach to extract the transport parameters from MGT measurements. Finally, we find the exponents that describe the intensity dependence of the transport parameters of majority and minority carriers in a HaP sample.
- 21 July 2020
- Published by IOP Publishing in Journal of Physics D: Applied Physics
- Vol. 53 (41) , 415107
Estimation of carrier mobilities and recombination lifetime in halide perovskites films using the moving grating technique
Pulsed excitation methods followed by time-resolved measurements have been questioned as a valid procedure to deduce transport properties of halide perovskites (HaPs). Measurements of both the majority and minority carrier’s phototransport properties, under illumination conditions as close as possible to one sun, are needed to obtain reliable information on recombination mechanisms. In this work, we show that the moving photocarrier grating technique (MGT) fulfills the above-mentioned conditions. In this method, both carriers mobilities and the common recombination lifetime are deduced from the DC short circuit current induced by the movement of an interference pattern along the sample surface. We show that the method, originally developed to measure the transport parameters of amorphous semiconductors, can be fully applied to HaPs films. We briefly describe the technique, we perform measurements as a function of the grating period and the light intensity, and we discuss the best approach to extract the transport parameters from MGT measurements. Finally, we find the exponents that describe the intensity dependence of the transport parameters of majority and minority carriers in a HaP sample.
- 17 June 2020
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 127 (23) , 235501
External quantum efficiency measurements used to study the stability of differently deposited perovskite solar cells
The instability exhibited by perovskite solar cells when exposed to the environment under illumination is one of the major obstacles for the entry of perovskite technology in the photovoltaic market. In this work, we use the external quantum efficiency (EQE) technique to study the photoinduced degradation of two types of solar cells having CH3NH3PbI3 as an absorber layer: one deposited by spin coating with an n-i-p architecture and the other deposited by evaporation with an inverted p-i-n structure. We also study the effect of different encapsulants to protect the cells against atmospheric agents. We find that EQE provides information regarding the areas of the cell most susceptible to degradation, in addition to providing an estimate of the optical gap and the Urbach energy of the absorbent material. We confirm that the combined action of illumination and the environment markedly accelerate the degradation, which is reflected in the deterioration of all the parameters of the cell. The rear part of the cell is the first region to suffer the light-induced degradation. On the other hand, the cells deposited by evaporation and with a good encapsulation process are highly stable since after 30 h of exposure just a small spectral change is noticed in the red/infrared region of the EQE spectrum.
- 17 June 2020
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 127 (23) , 235501
External quantum efficiency measurements used to study the stability of differently deposited perovskite solar cells
The instability exhibited by perovskite solar cells when exposed to the environment under illumination is one of the major obstacles for the entry of perovskite technology in the photovoltaic market. In this work, we use the external quantum efficiency (EQE) technique to study the photoinduced degradation of two types of solar cells having CH3NH3PbI3 as an absorber layer: one deposited by spin coating with an n-i-p architecture and the other deposited by evaporation with an inverted p-i-n structure. We also study the effect of different encapsulants to protect the cells against atmospheric agents. We find that EQE provides information regarding the areas of the cell most susceptible to degradation, in addition to providing an estimate of the optical gap and the Urbach energy of the absorbent material. We confirm that the combined action of illumination and the environment markedly accelerate the degradation, which is reflected in the deterioration of all the parameters of the cell. The rear part of the cell is the first region to suffer the light-induced degradation. On the other hand, the cells deposited by evaporation and with a good encapsulation process are highly stable since after 30 h of exposure just a small spectral change is noticed in the red/infrared region of the EQE spectrum.
- 1 December 2019
- Published by AIP Publishing in Review of Scientific Instruments
- Vol. 90 (12) , 123902
The chopped moving photocarrier grating technique
The Moving photocarrier Grating Technique (MGT) allows the simultaneous determination of the photocarrier drift mobilities and the small-signal recombination lifetime of photoconductive semiconductors. The technique measures the direct current (DC) induced by a monochromatic illumination consisting of a moving interference pattern superimposed on a uniform background of much higher intensity. A drawback of the technique is the low level of the signal to be measured, which can be masked by the noise at low temperatures or low light intensities. In this work, we propose implementing an alternating current (AC) version of the MGT by chopping the weak beam in the standard configuration. We call this new technique the Chopped Moving photocarrier Grating (CMG). In CMG, the AC signal can be measured with a lock-in amplifier for electrical noise removal. In this way, the signal-to-noise ratio can be increased compared to the standard DC technique. Assuming a multiple-trapping model for charge transport, we find the theoretical expression for the current density induced by CMG at fundamental frequency. By using a numerical simulation with parameters typical for hydrogenated amorphous silicon, we verify the expected equivalence between both techniques for low enough chopping frequencies. Then, we test experimentally this equivalence for an undoped hydrogenated amorphous silicon sample. For low signal levels, we demonstrate the superior performance of CMG.
- 1 December 2019
- Published by AIP Publishing in Review of Scientific Instruments
- Vol. 90 (12) , 123902
The chopped moving photocarrier grating technique
The Moving photocarrier Grating Technique (MGT) allows the simultaneous determination of the photocarrier drift mobilities and the small-signal recombination lifetime of photoconductive semiconductors. The technique measures the direct current (DC) induced by a monochromatic illumination consisting of a moving interference pattern superimposed on a uniform background of much higher intensity. A drawback of the technique is the low level of the signal to be measured, which can be masked by the noise at low temperatures or low light intensities. In this work, we propose implementing an alternating current (AC) version of the MGT by chopping the weak beam in the standard configuration. We call this new technique the Chopped Moving photocarrier Grating (CMG). In CMG, the AC signal can be measured with a lock-in amplifier for electrical noise removal. In this way, the signal-to-noise ratio can be increased compared to the standard DC technique. Assuming a multiple-trapping model for charge transport, we find the theoretical expression for the current density induced by CMG at fundamental frequency. By using a numerical simulation with parameters typical for hydrogenated amorphous silicon, we verify the expected equivalence between both techniques for low enough chopping frequencies. Then, we test experimentally this equivalence for an undoped hydrogenated amorphous silicon sample. For low signal levels, we demonstrate the superior performance of CMG.
- 4 June 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Photovoltaics
- Vol. 8 (4) , 1005-1010
Shunt Quenching and Concept of Independent Global Shunt in Multijunction Solar Cells
We show that two-terminal multijunction cells interconnected by tunnel junctions are fairly immune to individual local shunts, thanks to the shunt quenching. Interestingly, they may still suffer from global shunts. We revise the paradigm of a multijunction cell as a simple serial connection of component cells. This paradigm remains valid only for multijunction cells with laterally conductive interlayers. Instead, a new equivalent circuit is proposed and verified by measurement and simulations. As a main approach, selective illumination is applied and the voltage is measured at the end terminals. The global shunt is seen as a shift from logarithmic to linear intensity response. The presence of tunnel junction is important for an optimum configuration of tandem structures such as metal-halide perovskite with crystalline silicon solar cell.
- 4 June 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Photovoltaics
- Vol. 8 (4) , 1005-1010
Shunt Quenching and Concept of Independent Global Shunt in Multijunction Solar Cells
We show that two-terminal multijunction cells interconnected by tunnel junctions are fairly immune to individual local shunts, thanks to the shunt quenching. Interestingly, they may still suffer from global shunts. We revise the paradigm of a multijunction cell as a simple serial connection of component cells. This paradigm remains valid only for multijunction cells with laterally conductive interlayers. Instead, a new equivalent circuit is proposed and verified by measurement and simulations. As a main approach, selective illumination is applied and the voltage is measured at the end terminals. The global shunt is seen as a shift from logarithmic to linear intensity response. The presence of tunnel junction is important for an optimum configuration of tandem structures such as metal-halide perovskite with crystalline silicon solar cell.
- 8 March 2016
- Published by Wiley in Physica Status Solidi (a)
- Vol. 213 (7) , 1983-1988
Challenges in advanced characterization techniques for high Voc thin‐film tandem solar cells
In this work we focus on two techniques developed to extract the individual open circuit voltages (Voc) of tandem devices, as well as their sub‐cell current–voltage (I–V) characteristics. These were developed to work on the micromorph cell, the subcells of which have only a limited region of overlapping photoresponse due to the very different band gaps of its constituent cells, which allows for selective illumination. However, it is not known if such techniques will work in tandem structures consisting of high Voc structures (compared to the micromorph device), such as combinations of hydrogenated amorphous silicon oxide (a‐SiO:H), polymorphous silicon (pm‐Si:H), and amorphous silicon (a‐Si:H) in a‐SiO:H/pmSi:H a‐Si:H/pm‐Si:H device stacks. These novel structures have proven to suffer from less light induced degradation (LID), which is one of the main drawbacks of devices using a‐Si:H. The presence of similar band gaps (difference of less than 150 mV in both cases) and overlapping external quantum efficiencies (EQEs) above 500 nm implies that some of the hypotheses used may not be valid for high Voc devices. In this work we show the difficulties that arise when using these characterization techniques in such devices.
- 8 March 2016
- Published by Wiley in Physica Status Solidi (a)
- Vol. 213 (7) , 1983-1988
Challenges in advanced characterization techniques for high Voc thin‐film tandem solar cells
In this work we focus on two techniques developed to extract the individual open circuit voltages (Voc) of tandem devices, as well as their sub‐cell current–voltage (I–V) characteristics. These were developed to work on the micromorph cell, the subcells of which have only a limited region of overlapping photoresponse due to the very different band gaps of its constituent cells, which allows for selective illumination. However, it is not known if such techniques will work in tandem structures consisting of high Voc structures (compared to the micromorph device), such as combinations of hydrogenated amorphous silicon oxide (a‐SiO:H), polymorphous silicon (pm‐Si:H), and amorphous silicon (a‐Si:H) in a‐SiO:H/pmSi:H a‐Si:H/pm‐Si:H device stacks. These novel structures have proven to suffer from less light induced degradation (LID), which is one of the main drawbacks of devices using a‐Si:H. The presence of similar band gaps (difference of less than 150 mV in both cases) and overlapping external quantum efficiencies (EQEs) above 500 nm implies that some of the hypotheses used may not be valid for high Voc devices. In this work we show the difficulties that arise when using these characterization techniques in such devices.