NNNarugopal Nayek

Narugopal Nayek

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Narugopal Nayek has a total of 16 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Design and Analysis of Truncated Velocity Tapered Sine-Waveguide Structure for Traveling-Wave Tube in THz Band

    by Narugopal Nayek, Ramesh Kumar Sonkar, Tapeshwar Tiwari, Ratnajit Bhattacharjee

    A truncated sine-waveguide traveling-wave tube (SWGTWT) is studied to obtain wideband amplification at 600 GHz. The cold test parameters are obtained and finalized through simulation to achieve minimum dispersion coupled with a high interaction impedance. The interaction impedance at various points of the beam tunnel cross section area is evaluated to choose the right shape of the electron beam for the TWT. The effect of velocity tapering on the SWG structure is studied. Particle-in-cell (PIC) simulation is carried out using cylindrical as well as sheet beams. The velocity-tapered structure exhibits higher power and efficiency. The maximum output power and 3-dB bandwidth are estimated to be 7 W and 40 GHz, respectively. The corresponding gain and electronic efficiency of the truncated SWGTWT are 25.4 dB, and 1.88%, respectively.


  • Design and Analysis of Width-Modulated Two-Section Sine Waveguide for G-Band Traveling-Wave Tube

    by Narugopal Nayek, Mohit Kumar Joshi, Ramesh Kumar Sonkar, Tapeshwar Tiwari, Ratnajit Bhattacharjee

    A novel width-modulated sine waveguide traveling-wave tube (SWGTWT) is proposed for G-band operation. The broadband single-section and two-section SWGTWT are analyzed, which has the potential to address various technological challenges in the THz regime, such as fabrication difficulty, reflection, and attenuation of RF power. The two-section design has separate RF structures for input and output sections of the TWT, which helps to eliminate undesired reflection during high-power operation. The width modulation is employed to enhance the interaction impedance and also to realize the flat dispersion characteristic of the slow wave structure (SWS). The fabrication feasibility of the structure is demonstrated by fabricating the scaled structure at the Ku-band. A 20.4-kV, 50-mA cylindrical beam is employed in the particle-in-cell (PIC) simulation. The single-section structure offers a maximum power of 53 W with a 5.19% efficiency at 210 GHz. The peak power and a 3-dB bandwidth for the two-section structure are estimated to be 38.9 W and 32.5 GHz, respectively. The structure produces greater than 10 W of output power over a 46-GHz frequency band covering the range of 200-246 GHz.


  • Open Access

    Design and Development of High Power Broad Band Dry RF Load

    by Narugopal Nayek, Arvind Naik, Manoj Phatangare, T. Tiwari

    High power S-Band ferrite based RF load is designed and developed which is capable of handling 3 kW average power at operating frequency 2998±20 MHz . Electrical and thermal design is carried out using CST Studio Suite. Mechanical parts are fabricated according to the design. Water cooling is provided to the absorbing ferrites to support high power operation. Various RF load parts are fabricated, chemically cleaned and brazed. The experimental return loss better than 30 dB for a bandwidth of 250 MHz is achieved. The numerical and experimental results are discussed and presented in this paper.


  • Design and Efficiency Enhancement of a Ka-Band Industrial Gyrotron

    by Narugopal Nayek, Mohit Kumar Joshi, Ramesh Kumar Sonkar, Tapeshwar Tiwari, Ratnajit Bhattacharjee

    The key subsystems of a high efficiency material processing gyrotron are designed at an operating frequency of 27.885 GHz. A triode-type electron gun is designed to launch hollow spiraling electron beam. The outer diameter of the gun is kept at 50 mm to lower inside diameter of the magnet. Start oscillation current for TE₀₂ operating as well as competing modes is plotted. The output power and efficiency are predicted to be 18.4 kW and 46%, respectively, based on single mode time-dependent analytical equation. Beam-wave interaction is studied by employing particle-in-cell (PIC) simulation. Electronic efficiency and output power are increased by operating the tube in hard excitation region. An axially slotted cavity is adopted to abridge mode competitions. The output power and electronic efficiency are obtained to be 20.08 kW and 50.2%, respectively, without considering any velocity spread of the electron beam. However, the efficiency is reduced to 45%, when a moderate transverse velocity spread of 5% is considered. The power efficiency is enhanced to 67.07% by introducing a 3-staged depressed collector.


  • Design and Analysis of Overmoded RF Window for High-Power Applications in $X$ -Band

    by Mohit Kumar Joshi, Narugopal Nayek, Tapeshwar Tiwari, Ratnajit Bhattacharjee

    This article presents the design and analysis of overmoded RF window for megawatt-class pulsed coaxial magnetron operating in X-band and other high-power systems such as linear accelerator (LINAC) and devices such as gyrotron and klystron. Three ingenious designs of RF windows are proposed based on the mode excitation techniques. Design 1 operates in TE₀₁₂-type mode (mixed with TE₁₁₃ and TE₂₁₃), Design 2 in TE₀₁₂-type mode (mixed with TE₃₁₂), and Design 3 in TE₀₁₄-type mode. Mixed-mode operation broadens the bandwidth of the RF window compared to single-mode operation. RF windows are simulated in CST and return losses are obtained as 55.04, 51.52, and 53.92 dB, and insertion losses as 0.054, 0.07, 0.194 dB, respectively. Return losses and insertion losses of the proposed designs are verified in HFSS, and results are in good agreement with the results obtained from CST. Coupled multiphysics analyses are carried out to study thermal and structural behaviors of the proposed RF windows. Sensitivity analysis of the windows is also performed to analyze the effect of mechanical deformation on the performance of S-parameters. Multipactor analysis is carried out to determine the safe operating power level, and multipactor thresholds are obtained as 10, 16, and 2.35 MW, respectively.


  • Sapphire based high-power microwave window

    by Narugopal Nayek, K Subhadra, Manoj Kandpal, Arijit Majumdar, Sayan Chatterjee, C. S. Nainwad, R. Krishnan, Subrata Das

    Dielectric windows often limit the power handling capability of vacuum electron devices. It is necessary to choose the right dielectric material for high power applications. Depending upon the power level, a range of materials has been used in various systems. The ideal material should have high mechanical strength, high thermal conductivity, high electrical breakdown voltage, low dielectric loss, favourable dielectric constant and easy joinability to metal parts. In order to make a judicious compromise between the material with highly desirable properties and easy availability, sapphire is chosen for the present work. UHV grade joining technique between sapphire and metal has been developed. The dimensions of the dielectric and other components in a pill-box type window design have been optimised using HFSS. The heat transfer and cooling parameters have been optimised using numerical techniques. The design details, fabrication processes and low-power characterisation will be discussed in the paper.