Ivan Lisovskyi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Ivan Lisovskyi has a total of 41 co-authors. Here are the top co-authors by number of shared publications:
- Anatolii Grigorievich Belous
V.I. Vernadsky Institute of General and Inorganic Chemistry of the National Academy of Sciences of Ukraine 2 , Palladina Ave., 32/34, Kyiv 03142
6 shared publications - Sergii Solopan
V.I. Vernadskii Institute of General and Inorganic Chemistry of the NAS of Ukraine,Solid State Chemistry Department,Kyiv,Ukraine
4 shared publications A. G. Belous
V. I.Vernadsky Institute of General and Inorganic Chemistry of the NAS of Ukraine, Kiev, Ukraine
3 shared publicationsLeonid Kovalenko
V. I. Vernadsky Institute of General and Inorganic Chemistry of the NAS of Ukraine, Kyiv, Ukraine
3 shared publicationsV. G. Khomenko
Kyiv National University of Technologies and Design, Kiev, Ukraine
3 shared publications- Volodymyr Khomenko
Kyiv National University of Technologies and Design
3 shared publications
Latest Publications
- Open Access
- 30 October 2026
- Published by Wiley in Batteries & Supercaps
- Vol. 9 (11) , e70523
Ion‐Conducting Ceramics in Lithium‐Ion Batteries: From Electrode Modification to Composite Electrolytes for Quasi‐Solid‐State Cells
The development of lithium‐based batteries requires advanced electrolyte systems capable of ensuring efficient ion transport and reliable electrode–electrolyte interfaces. In this work, inorganic lithium‐ion conductors have been investigated as components of composite polymer electrolytes and as functional modifiers of Li 4 Ti 5 O 12 anodes. Li 4 Ti 5 O 12 was modified by mechanical mixing with 1 wt% of representative ion conductors, including NASICON‐type Li 1.3 Al 0.3 Ti 1.7 (PO 4 ) 3 (LATP), garnet‐type Li 6.5 La 3 Zr 1.5 Nb 0.5 O 12 (LLZNO), and perovskite‐type Li 0.5 La 0.5 TiO 3 (LLTO), intended to distribute the ceramic particles over the LTO surface as a physical (nonbonded) coating, and evaluated in lithium‐ion cells employing either a conventional liquid electrolyte or quasi‐solid‐state composite polymer electrolytes. Electrochemical characterization by galvanostatic cycling and cyclic voltammetry demonstrated distinct electrochemical behavior depending on the incorporated ceramic phase, with LATP‐containing systems showing the most favorable rate performance and overall internal resistance among the investigated modified configurations. In the quasi‐solid‐state cells, the higher internal resistance compared with liquid‐electrolyte cells limited the rate capability at high currents, while stable cycling was observed at 1C. Furthermore, laboratory‐scale quasi‐solid‐state pouch cells employing the composite polymer electrolyte delivered a discharge capacity of 159 mAh·g −1 at C/10, comparable to that of the corresponding liquid‐electrolyte cells (148 mAh·g −1 ), with ~2% first‐cycle capacity loss.
- 30 October 2026
- Published by Wiley in Batteries & Supercaps
- Vol. 9 (11) , e70523
Open AccessIon‐Conducting Ceramics in Lithium‐Ion Batteries: From Electrode Modification to Composite Electrolytes for Quasi‐Solid‐State Cells
The development of lithium‐based batteries requires advanced electrolyte systems capable of ensuring efficient ion transport and reliable electrode–electrolyte interfaces. In this work, inorganic lithium‐ion conductors have been investigated as components of composite polymer electrolytes and as functional modifiers of Li 4 Ti 5 O 12 anodes. Li 4 Ti 5 O 12 was modified by mechanical mixing with 1 wt% of representative ion conductors, including NASICON‐type Li 1.3 Al 0.3 Ti 1.7 (PO 4 ) 3 (LATP), garnet‐type Li 6.5 La 3 Zr 1.5 Nb 0.5 O 12 (LLZNO), and perovskite‐type Li 0.5 La 0.5 TiO 3 (LLTO), intended to distribute the ceramic particles over the LTO surface as a physical (nonbonded) coating, and evaluated in lithium‐ion cells employing either a conventional liquid electrolyte or quasi‐solid‐state composite polymer electrolytes. Electrochemical characterization by galvanostatic cycling and cyclic voltammetry demonstrated distinct electrochemical behavior depending on the incorporated ceramic phase, with LATP‐containing systems showing the most favorable rate performance and overall internal resistance among the investigated modified configurations. In the quasi‐solid‐state cells, the higher internal resistance compared with liquid‐electrolyte cells limited the rate capability at high currents, while stable cycling was observed at 1C. Furthermore, laboratory‐scale quasi‐solid‐state pouch cells employing the composite polymer electrolyte delivered a discharge capacity of 159 mAh·g −1 at C/10, comparable to that of the corresponding liquid‐electrolyte cells (148 mAh·g −1 ), with ~2% first‐cycle capacity loss.
- 25 December 2025
- Published by Elsevier in Ceramics International
- Vol. 52 (5) , 6277-6290
Structure formation and physical properties of Gd-doped yttrium-iron ferrites: Nonlinear concentration–temperature effects and phase-dependent magnetic behaviour
- 25 December 2025
- Published by Elsevier in Ceramics International
- Vol. 52 (5) , 6277-6290
Structure formation and physical properties of Gd-doped yttrium-iron ferrites: Nonlinear concentration–temperature effects and phase-dependent magnetic behaviour
- 25 September 2025
- Published by V.I. Vernadsky Institute of General and Inorganic Chemistry in Ukrainian Chemistry Journal
- Vol. 91 (8)
POLYMERIC COMPOSITE ELECTROLYTE BASED ON NASICON FOR SOLID-STATE LITHIUM BATTERIES
A composite solid electrolyte based on the fluoropolymer Neoflon VT-475, the ionic liquid PYR14-TFSI, and the lithium salt LiTFSI has been developed and studied for use in solid-state lithium-ion batteries. As a lithium-conductive additive, nanoparticles of Li1.3Al0.3Ti1.7(PO4)3 (LATP) with a NASICON-type structure were introduced into the electrolyte composition, providing three-dimensional channels for efficient lithium-ion migration. LATP was synthesized using a sol-gel method, which enabled the production of particles with high ionic conductivity and a stable crystalline structure. The methodology for fabricating the electrolyte in the form of a film is described, along with its characteristics, including electrochemical properties, which were investigated in laboratory battery prototypes with a LiFePO4 (LFP) cathode and a Li4Ti5O12 (LTO) anode modified with LATP. To improve interfacial contact between the solid electrolyte and the electrodes, a liquid-phase treatment was applied. The electrode surfaces were additionally impregnated with a polymer solution to enhance adhesion and interfacial contact. This approach reduced interfacial resistance, improved ion transport, and ensured stable performance during long-term cycling. The study showed that the developed prototypes with the composite solid electrolyte demonstrated specific capacities comparable to those of samples with liquid electrolytes under current loads up to 4C. Long-term cycling statistics indicated a high level of stability, with capacity degradation not exceeding 6% after 130 full charge-discharge cycles. The developed electrolyte is promising for use in solid-state lithium-ion batteries with improved performance, safety, and durability, as its structure and composition help reduce dendrite formation risk, enhance interfacial layer stability, and maintain high ionic conductivity even under high loads.
- 25 September 2025
- Published by V.I. Vernadsky Institute of General and Inorganic Chemistry in Ukrainian Chemistry Journal
- Vol. 91 (8)
POLYMERIC COMPOSITE ELECTROLYTE BASED ON NASICON FOR SOLID-STATE LITHIUM BATTERIES
A composite solid electrolyte based on the fluoropolymer Neoflon VT-475, the ionic liquid PYR14-TFSI, and the lithium salt LiTFSI has been developed and studied for use in solid-state lithium-ion batteries. As a lithium-conductive additive, nanoparticles of Li1.3Al0.3Ti1.7(PO4)3 (LATP) with a NASICON-type structure were introduced into the electrolyte composition, providing three-dimensional channels for efficient lithium-ion migration. LATP was synthesized using a sol-gel method, which enabled the production of particles with high ionic conductivity and a stable crystalline structure. The methodology for fabricating the electrolyte in the form of a film is described, along with its characteristics, including electrochemical properties, which were investigated in laboratory battery prototypes with a LiFePO4 (LFP) cathode and a Li4Ti5O12 (LTO) anode modified with LATP. To improve interfacial contact between the solid electrolyte and the electrodes, a liquid-phase treatment was applied. The electrode surfaces were additionally impregnated with a polymer solution to enhance adhesion and interfacial contact. This approach reduced interfacial resistance, improved ion transport, and ensured stable performance during long-term cycling. The study showed that the developed prototypes with the composite solid electrolyte demonstrated specific capacities comparable to those of samples with liquid electrolytes under current loads up to 4C. Long-term cycling statistics indicated a high level of stability, with capacity degradation not exceeding 6% after 130 full charge-discharge cycles. The developed electrolyte is promising for use in solid-state lithium-ion batteries with improved performance, safety, and durability, as its structure and composition help reduce dendrite formation risk, enhance interfacial layer stability, and maintain high ionic conductivity even under high loads.
- 18 June 2025
- Published by Lviv Polytechnic National University in Chemistry & Chemical Technology
- Vol. 19 (2) , 270-276
Development of Membranes Based on Polyvinylidene Fluoride for Lithium Batteries
Two methods for producing lithium-conductive polymer films based on polyvinylidene fluoride (PVDF) were studied: saturating a dielectric PVDF film with a lithium-conductive solution and incorporating a lithium-conductive solution into a PVDF solution, followed by the fabrication of a lithium-conductive film. A comprehensive set of electrophysical studies on the properties of the proposed gel-polymer electrolyte across a wide temperature range (20–70 ℃) and frequency range (0.1 Hz–32 MHz) was conducted. Li-ion battery prototypes constructed using the engineered membrane exhibit improved performance and enhanced stability during charge/discharge cycling compared to cells with a commercial Celgard 2400 separator.
- 18 June 2025
- Published by Lviv Polytechnic National University in Chemistry & Chemical Technology
- Vol. 19 (2) , 270-276
Development of Membranes Based on Polyvinylidene Fluoride for Lithium Batteries
Two methods for producing lithium-conductive polymer films based on polyvinylidene fluoride (PVDF) were studied: saturating a dielectric PVDF film with a lithium-conductive solution and incorporating a lithium-conductive solution into a PVDF solution, followed by the fabrication of a lithium-conductive film. A comprehensive set of electrophysical studies on the properties of the proposed gel-polymer electrolyte across a wide temperature range (20–70 ℃) and frequency range (0.1 Hz–32 MHz) was conducted. Li-ion battery prototypes constructed using the engineered membrane exhibit improved performance and enhanced stability during charge/discharge cycling compared to cells with a commercial Celgard 2400 separator.
- 19 March 2025
- Published by Springer Nature in Journal of Applied Electrochemistry
- Vol. 55 (8) , 1963-1996
Surface modification of cathode materials with functional coatings for enhanced lithium-ion battery durability
- 19 March 2025
- Published by Springer Nature in Journal of Applied Electrochemistry
- Vol. 55 (8) , 1963-1996
Surface modification of cathode materials with functional coatings for enhanced lithium-ion battery durability
- Open Access
- 1 September 2024
- Published by IOP Publishing in Nano Express
- Vol. 5 (3) , 035021
Development of electrode and electrolyte materials for solid-state batteries based on Li1.3Al0.3Ti1.7(PO4)3
The dependence of the electrochemical characteristics of a layered cathode material containing LiNi0.5Mn0.3Co0.2O2 on the method for applying a protective layer of nanoparticles of the lithium-conducting material Li1.3Al0.3Ti1.7(PO4)3 with a NASICON structure to its surface has been studied. The surface modification has been found to improve the capacity retention in prolonged charge/discharge cycling (up to 15%) and to allow fast charge/discharge processes. The possibility of using a composite electrolyte consisting of a porous ceramic matrix of aluminum-substituted lithium titanium phosphate Li1.3Al0.3Ti1.7(PO4)3 with a transition layer of liquid electrolyte LP-71 has been shown. The use of a thick composite solid electrolyte results in a slight reduction (∼5–7 mAh g−1) in initial capacity compared to laboratory cells with the widely used Celgard 2400 separator impregnated with liquid electrolyte. Laboratory cells assembled with a composite electrolyte showed higher stability during charge/discharge cycling: after 80 deep charge/discharge cycles, the capacity reduction was ∼12% for cells with a composite electrolyte, while for the reference cell it was ∼23%.
- 1 September 2024
- Published by IOP Publishing in Nano Express
- Vol. 5 (3) , 035021
Open AccessDevelopment of electrode and electrolyte materials for solid-state batteries based on Li1.3Al0.3Ti1.7(PO4)3
The dependence of the electrochemical characteristics of a layered cathode material containing LiNi0.5Mn0.3Co0.2O2 on the method for applying a protective layer of nanoparticles of the lithium-conducting material Li1.3Al0.3Ti1.7(PO4)3 with a NASICON structure to its surface has been studied. The surface modification has been found to improve the capacity retention in prolonged charge/discharge cycling (up to 15%) and to allow fast charge/discharge processes. The possibility of using a composite electrolyte consisting of a porous ceramic matrix of aluminum-substituted lithium titanium phosphate Li1.3Al0.3Ti1.7(PO4)3 with a transition layer of liquid electrolyte LP-71 has been shown. The use of a thick composite solid electrolyte results in a slight reduction (∼5–7 mAh g−1) in initial capacity compared to laboratory cells with the widely used Celgard 2400 separator impregnated with liquid electrolyte. Laboratory cells assembled with a composite electrolyte showed higher stability during charge/discharge cycling: after 80 deep charge/discharge cycles, the capacity reduction was ∼12% for cells with a composite electrolyte, while for the reference cell it was ∼23%.
- Open Access
- 29 April 2024
- Published by V.I. Vernadsky Institute of General and Inorganic Chemistry in Ukrainian Chemistry Journal
- Vol. 90 (3) , 18-32
DEVELOPMENT OF COMPOSITE MATERIALS WITH INCREASED STABILITY FOR ENERGY-GENERATING AND ENERGY-SAVING SYSTEMS
Techniques for creating composite organic-inorganic materials by applying optically transparent polymers to the surface of the organic-inorganic perovskite CH3NH3PbI3 and composite cathode materials by modifying the surface of commercial cathode materials of the LiNixCoyAlzO2/LiNixMnyCozO2(NCA/NMC)type with nanoparticles of lithium oxide conductive material Li1.3Al .3Ti1.7(PO4)3 (LATP) have been developed. It was shown that, depending on the type of polymer, CH3NH3PbI3 perovskite degrades due to the formation of different amounts of additional crystalline phases.It was established that the degree of degradation of the perovskite (1:2) CH3NH3PbI3 film is 100% after 220 days of influence to moisture and oxygen. Under the influence of moisture and oxygen for 500 days, perovskite/polymer films: PVB, SOC, and PVDC degrade only by 1.55%, 1.65% and 3.5%, respectively, which is 65, 60 and 29 times less than for pure perovskite CH3NH3PbI3. The dependence of the electrochemical characteristics of a layered cathode material containing NCA/NMCon the method for applying a protective layer (mechanical application and sol-gel method) of nanoparticles of the lithium-conducting material LATP with a NASICON structure to its surface has been studied.It was found that for composite cathode materials based on NMC 111, the capacity drop during 80 charge/discharge cycles is reduced by 10–14% compared to the initial NMC 111. At the same time, the suitability of the cathode material NMC 111m(T) for the rapid charge/discharge process is 4–6% higher than that of the initial cathode material.It is shown that both investigated methods of creating composite materials based on cathode materials with a high nickel content (NMC 811 and NCA) and LATP nanoparticles do not lead to improvement of their electrochemical characteristics.
- 29 April 2024
- Published by V.I. Vernadsky Institute of General and Inorganic Chemistry in Ukrainian Chemistry Journal
- Vol. 90 (3) , 18-32
Open AccessDEVELOPMENT OF COMPOSITE MATERIALS WITH INCREASED STABILITY FOR ENERGY-GENERATING AND ENERGY-SAVING SYSTEMS
Techniques for creating composite organic-inorganic materials by applying optically transparent polymers to the surface of the organic-inorganic perovskite CH3NH3PbI3 and composite cathode materials by modifying the surface of commercial cathode materials of the LiNixCoyAlzO2/LiNixMnyCozO2(NCA/NMC)type with nanoparticles of lithium oxide conductive material Li1.3Al .3Ti1.7(PO4)3 (LATP) have been developed. It was shown that, depending on the type of polymer, CH3NH3PbI3 perovskite degrades due to the formation of different amounts of additional crystalline phases.It was established that the degree of degradation of the perovskite (1:2) CH3NH3PbI3 film is 100% after 220 days of influence to moisture and oxygen. Under the influence of moisture and oxygen for 500 days, perovskite/polymer films: PVB, SOC, and PVDC degrade only by 1.55%, 1.65% and 3.5%, respectively, which is 65, 60 and 29 times less than for pure perovskite CH3NH3PbI3. The dependence of the electrochemical characteristics of a layered cathode material containing NCA/NMCon the method for applying a protective layer (mechanical application and sol-gel method) of nanoparticles of the lithium-conducting material LATP with a NASICON structure to its surface has been studied.It was found that for composite cathode materials based on NMC 111, the capacity drop during 80 charge/discharge cycles is reduced by 10–14% compared to the initial NMC 111. At the same time, the suitability of the cathode material NMC 111m(T) for the rapid charge/discharge process is 4–6% higher than that of the initial cathode material.It is shown that both investigated methods of creating composite materials based on cathode materials with a high nickel content (NMC 811 and NCA) and LATP nanoparticles do not lead to improvement of their electrochemical characteristics.
- 1 November 2023
- Published by Springer Nature in Theoretical and Experimental Chemistry
- Vol. 59 (5) , 324-331
Influence of Surface Modification of Layered Cathode Materials LiNixMnyCozO2 by NASICON Structure Nanoparticles on Their Electrochemical Characteristics
- 1 November 2023
- Published by Springer Nature in Theoretical and Experimental Chemistry
- Vol. 59 (5) , 324-331
Influence of Surface Modification of Layered Cathode Materials LiNixMnyCozO2 by NASICON Structure Nanoparticles on Their Electrochemical Characteristics
- Open Access
- 24 February 2023
- Published by V.I. Vernadsky Institute of General and Inorganic Chemistry in Ukrainian Chemistry Journal
- Vol. 89 (1) , 3-17
SYNTHESIS AND INVESTIGATION OF ELECTROCHEMICAL CHARACTERISTICS OF OXIDE Li-CONDUCTIVE MATERIALS WITH SPINEL AND PEROSKITE STRUCTURES
Lithium-ion batteries (LIBs) are widely used in electronic devices due to their numerous advantages, namely high energy density, high capacity, and long service life. One of the important components of a battery is the anode. In order to ensure high characteristics of LIB, the anode material must have high capacity, high ionic and electronic conductivities, and low cost. However, commonly used anode materials in lithium-ion batteries have a number of disadvantages. For example, a graphite-based anode is characterized by significant changes in volume during intercalation/deintercalation of lithium ions, high energy losses, and rapid deterioration of characteristics at high discharge/charge rates; Li4Ti5O12 have a low theoretical specific capacity, low electronic conductivity and low diffusion rate of lithium ions. Thus, the search for anode materials with high capacity and capability rate, as well as small volume change during lithium intercalation/deintercalation, remains an urgent task. A promising way may be the use of materials with intercalation pseudocapacitive behavior of charge accumulation, which occurs due to the intercalation of ions in tunnels or layers of active materials without a crystallographic phase transition. LixLa2/3-x/3TiO3 is well known as a superionic conductor with a high ionic conductivity σ ≈ 10–3 S/cm at room temperature. It crystallizes in a perovskite-type structure that consists of a framework of TiO6 octahedra stabilized by La atoms, and has numerous vacancies in the unoccupied positions 18d and 6a, that could participate in the storage and motion of Li ions. Electrochemical characteristics of LixLa2/3-x/3TiO3 (x = 0.35 and 0.5) anode materials with a perovskite structure were investigated and compared with the electrochemical characteristics of Li4Ti5O12 with a layered spinel structure.
- 24 February 2023
- Published by V.I. Vernadsky Institute of General and Inorganic Chemistry in Ukrainian Chemistry Journal
- Vol. 89 (1) , 3-17
Open AccessSYNTHESIS AND INVESTIGATION OF ELECTROCHEMICAL CHARACTERISTICS OF OXIDE Li-CONDUCTIVE MATERIALS WITH SPINEL AND PEROSKITE STRUCTURES
Lithium-ion batteries (LIBs) are widely used in electronic devices due to their numerous advantages, namely high energy density, high capacity, and long service life. One of the important components of a battery is the anode. In order to ensure high characteristics of LIB, the anode material must have high capacity, high ionic and electronic conductivities, and low cost. However, commonly used anode materials in lithium-ion batteries have a number of disadvantages. For example, a graphite-based anode is characterized by significant changes in volume during intercalation/deintercalation of lithium ions, high energy losses, and rapid deterioration of characteristics at high discharge/charge rates; Li4Ti5O12 have a low theoretical specific capacity, low electronic conductivity and low diffusion rate of lithium ions. Thus, the search for anode materials with high capacity and capability rate, as well as small volume change during lithium intercalation/deintercalation, remains an urgent task. A promising way may be the use of materials with intercalation pseudocapacitive behavior of charge accumulation, which occurs due to the intercalation of ions in tunnels or layers of active materials without a crystallographic phase transition. LixLa2/3-x/3TiO3 is well known as a superionic conductor with a high ionic conductivity σ ≈ 10–3 S/cm at room temperature. It crystallizes in a perovskite-type structure that consists of a framework of TiO6 octahedra stabilized by La atoms, and has numerous vacancies in the unoccupied positions 18d and 6a, that could participate in the storage and motion of Li ions. Electrochemical characteristics of LixLa2/3-x/3TiO3 (x = 0.35 and 0.5) anode materials with a perovskite structure were investigated and compared with the electrochemical characteristics of Li4Ti5O12 with a layered spinel structure.