EPEduard Parusov

Eduard Parusov

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Eduard Parusov has a total of 44 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Influence of laser processing of steels on the sizes of nonmetallic inclusions in a strenghened layer

    by S. I. Gubenko, E. V. Parusov, O. V. Parusov

    Specific features of the influence of laser processing on the sizes and volume fraction of non-metallic inclusions of various types in the strengthened layer of steels are studied. Laser processing of steels allows us to reduce the average size of non-metallic inclusions and the contamination of steel with inclusions in the strengthened zone by 30–50%. For different types of inclusions and steels, parameters which characterize the average sizes of inclusions and their volume fraction in the strengthened layer depending on the laser exposure effect are determined. The mechanisms and features of the transformation of non-metallic inclu¬sions during laser exposure, which contribute to a reduction in their size (crushing during partial dissolution and melting, mechanical crushing of solid or liquid initial inclusions, formation of dispersed “satellite” particles in microcomposite saturation zones of the steel matrix near the initial inclusions) are discussed.

  • Features of the transformation of heterophase non-metallic inclusions during hot and cold rolling of steels. Part 1

    by S. I. Gubenko, E. V. Parusov, I. M. Chuiko, O. V. Parusov

    The behavior of microcomposite heterophase inclusions of the types “refractory phase encased in a fusible shell” and “phases are beside” during hot and cold rolling of steels has been investigated. It is demonstrated that their deformation behavior is governed by the complex interaction of the constituent phases within the inclusions, as well as by the interactions across the inclusion–matrix interfaces and the internal interphase boundaries inside the inclusions. The study establishes that these inclusions exhibit characteristic patterns of deformation processes determined by their chemical and phase composition, structure, deformability of the inclusion phases, and deformation temperature. The mutual influence of the phases on their joint deformation under hot and cold rolling conditions has been identified. It is shown that the morphological evolution of inclusions of the “refractory phase encased in a fusible shell” type during hot rolling is controlled by the plasticity of the shell phase and the complex interphase interactions resulting from interfacial friction and slip. The encapsulation of undeformable inclusions such as oxides, spinels, titanium nitride, and others within a plastic silicate or sulfide shell can be regarded as an effective mechanism for reducing the brittleness of nonmetallic inclusions during hot rolling. The shape evolution of “phases are beside” inclusions during hot rolling is determined by the plasticity of the inclusion phases and by complex interphase interactions arising from interfacial friction and slip (provided a plastic phase is present). During cold rolling, the morphological evolution of “refractory phase encased in a fusible shell” inclusions is controlled by the plasticity of the sulfide shell phase, together with complex interphase interactions involving interfacial friction and cold slip along interphase boundaries inside the inclusions. In the case of “phases are beside” inclusions, their shape change during cold rolling is governed by the plasticity of the sulfide phase (if present), as well as by interfacial friction and cold slip processes. The role of plastic phases in inclusions of both types has been clarified. It is demonstrated that plastic phases and interphase boundaries play a decisive role in the morphological evolution of heterophase inclusions of the “refractory phase encased in a fusible shell” and “phases are beside” types during hot and cold rolling of steels.

  • Iron and Steel Institute of Z. I. Nekrasov of National Academy of Sciences of Ukraine: scientific achievements and paths of strategic development

    by O. I. Babachenko, E. V. Parusov, L. I. Garmash

    The article summarizes the results of the activities of the Iron and Steel Institute of Z. I. Nekrasov National Academy of Sciences of Ukraine in the context of modern challenges, in particular martial law, significant transformation of the economy and industry, and the need for integration into the European Research Area. It is shown that despite the difficult operating conditions in 2019-2025, the Iron and Steel Institute managed to maintain scientific productivity, ensure a high level of fundamental and applied research, and even receive high marks for its activities - according to the results of the state certification of the Ministry of Education and Science of Ukraine and the assessment of the NAS of Ukraine, the Institute received the highest category "A". The new system of assessment of scientific institutions, introduced by the Ministry of Education and Science, which combines quantitative indicators and expert assessment, is analyzed, its advantages and disadvantages are identified. The impact of the certification results on the financing, organizational development, and international competitiveness of the Institute is highlighted. It is noted that one of the features of the certification of the Ministry of Education and Science is to bring its results to the level of scientific units. The main scientific achievements of the Iron and Steel Institute in recent years in key areas of metallurgy are presented: blast furnace production, non-furnace processing of cast iron, steelmaking processes, rolling production, heat treatment, materials science, development of technological equipment and control systems. Particular attention is paid to developments aimed at increasing energy efficiency, decarbonization of production, import substitution and restoration of the industry. The role of the Institute as a leading scientific center that provides a full cycle of research in ferrous metallurgy, promotes the training of scientific personnel, the development of international cooperation and the introduction of innovations into industry is emphasized. The experience of the Institute in recent years convincingly demonstrates that, provided that the fundamental scientific principles are preserved and interaction with the industrial sector is strengthened, academic scientific institutions are able to effectively adapt to new operating conditions and maintain their scientific potential, ensuring the technological development of the state.

  • СТВОРЕННЯ ПРОГРАМНОГО ІНСТРУМЕНТУ ДЛЯ РОЗРОБЛЕННЯ ЕФЕКТИВНОЇ ТЕХНОЛОГІЇ ВОЛОЧІННЯ ЗВАРЮВАЛЬНОГО ДРОТУ З НИЗЬКОВУГЛЕЦЕВИХ CR-MO-V СТАЛЕЙ

    by Е.в. Олійник, Е.в. Парусов, І.м. Чуйко

    Based on the analysis of data from the industrial processing of experimental batches of wire rod made of low-carbon Cr-Mo-V steels intended for the production of welding wire, an empirical coefficient of the modified Tulenkov-Zolotnikov equation was determined that takes into account the actual chemical composition of the metal and its structural state. Using the established relationships, a specialized module of the CalcRoutes software package was developed for predicting the energy-force parameters of drawing and the mechanical properties of cold-deformed welding wire. This makes it possible to calculate drawing routes, determine the kinematic scheme of wire rod elongation, drawing speeds, the ultimate tensile strength of the steel after passing through each deformation zone, the load factor of electric motors, the total drawing power, and wire production capacity taking into account the available working time fund. The obtained data can be used by specialists of hardware plants during the development and improvement of the technology for producing welding wire from low-carbon Cr-Mo-V steels.

  • On the Formation of Martensite in Low-Carbon Alloy Steel Wire Rod for Welding Applications during Slow Continuous Cooling

    by Eduard Parusov, Ihor Chuiko, Serhii Bobyr, Eduard Oliinyk, Viktor Zhukov

    Relevance of the work. One of the key challenges currently faced by manufacturers of steel wire rod for welding applications worldwide is achieving maximum plasticity in the metal before delivery to hardware plants. This need arises due to the ongoing technological advancements in hardware plants and the integration of modern equipment capable of producing wire at high drawing speeds with significant degrees of unit deformation. Such processes demand high-quality raw materials (wire rod). Another crucial aspect is ensuring a high-quality surface for the welding wire, free from microcracks and hard inclusions. These defects can negatively impact the welding process by increasing metal spatter, causing electric arc instability, and leading to critical defects in welded joints, such as cavities and cracks. Rational microstructural design is a key principle in producing highly plastic wire rod for the efficient manufacturing of solid-section welding wire from low-carbon alloy steels. The presence of hard components (such as martensite, bainite, or their mixtures) in the wire rod’s structure is undesirable, as they increase the risk of metal failure during intensive cold deformation by drawing. Minimizing these hard phases remains an urgent scientific and practical challenge. The aim of the study is to determine the mechanism of martensite grains formation during slow cooling of low-carbon alloy steel grade CrMoV1Si wire rod, used for producing welding wire, from the austenitization temperature to room temperature. Material and methodology. The material used in this study was steel with the chemical composition (in wt.%) 0.08C–1.30Mn–0.54Si–1.06Cr–0.54Mo–0.24V–Fe ( balance ) . The samples were subjected to thermal cycles using an automated Gleeble 3800 thermal deformation simulation system. The thermal cycle involved heating the samples to the temperature required for complete austenitization, holding them at this temperature, and then continuously cooling at controlled rates of 0.20, 0.10, and 0.05 °C/s to room temperature. Metallographic analysis was conducted using an optical microscope and a scanning electron microscope. The hardness of individual structural components was measured using a microhardness tester following the standard method. The chemical composition of the phases was determined by energy-dispersive X-ray spectroscopy and Auger electron spectroscopy. Results. The study established an anomalous increase in the volume fraction of austenite shear transformation products in CrMoV1Si steel after continuous slow cooling at rates of 0.20–0.05 °C/s, at the same time, martensite had a relatively high carbon content (up to 1.6 wt.%). The authors attribute this microstructural evolution to dynamic changes in the chemical composition of individual phases during cooling, primarily due to the partitioning of carbon and other alloying elements between the α and γ phases, as confirmed experimentally. Based on the obtained results, a mechanism has been proposed for the formation of high-carbon martensite grains in low-carbon alloy steel wire rod during slow cooling from the austenitization temperature to room temperature.


  • Thermomechanical treatment technology of wire rod made of low-carbon Cr-Mo-V steels

    by E.V. Parusov, I.M. Chuiko, E.V. Oliinyk, O.V. Parusov

    Automatic Welding, 2025, №06. Journal «AVTOMATICHESKAYA SVARKA» Monthly scientific-technical and production journal. ISSN: 0005-111X, Since 1948. Russian version of «The PATON Welding Journal» Text in Russian, contents and summaries in English. The Journal presents a wide range of scientific-technical and promotion information in the field of technologies, equipment and materials for welding, surfacing, brazing, and deposition of protective coatings.

  • Дослідження закономірностей формування структури прокату зі сталі CrMoV1Si під час моделювання промислових режимів повітряного охолодження

    by E. V. Oliinyk, E. V. Parusov, I. M. Chuiko, O. V. Parusov, T. M. Golubenko

    The patterns and features of structure formation in low-carbon alloyed CrMoV1Si steel intended for welding applications were studied through laboratory simulation of industrial continuous controlled air cooling modes. In determining the temperature-time parameters of the thermal cycles, it was necessary to apply quasi-isothermal holding of the wire rod within the range of diffusion transformation of undercooled austenite, taking into account the technological specifics of operating Stelmor-type cooling lines in the production flow of rolling mills at three manufacturing plants. The fundamental distinction of the simulated modes lies in the varying cooling rates within the temperature range of the diffusion γ → α transformation, determined by the actual length of the air cooling sections on Stelmor lines, which are equipped with heat-insulating hoods, and by the minimum permissible conveyor speed for metal transport. A new scientifically grounded temperature-rate schedule of differentiated continuous air cooling for the studied steel was proposed, aimed at minimizing the amount of hard phases (martensite and bainite) formed in the metal structure: starting air cooling temperature – 950 °C; accelerated cooling within 950-850 °C at a rate of ~10 °C/s; slow cooling within 850-570 °C at a rate of ~0.4 °C/s; cooling from 570 °C to room temperature in still air. As a result, the structure of the studied steel comprises 60 vol.% polyhedral ferrite, 29 vol.% pearlite, 8 vol.% bainite, and 3 vol.% martensite in the form of relatively uniformly distributed individual grains with high hardness. Faster or slower cooling of the steel within the γ → α transformation range, compared to the developed mode, leads to an increase in the amount of quenching structures formed. The identified structural formation characteristics in CrMoV1Si steel provide the basis for the development and practical implementation of a softening thermomechanical treatment technology for wire rod made from low-carbon Cr-Mo-V welding steels under industrial conditions in metallurgical plants.

  • Open Access

    Development of a method for laser strengthening of railway wheel tread

    by E.V. Parusov, S.I. Gubenko, I.M. Chuiko, O.V. Parusov

    The goal of this work was to develop a method for laser strengthening of the cove zone of railway wheels in order to obtain a bainitic structure and eliminate undercutting of the crests. Methodology. Laser irradiation of the samples was performed in continuous radiation mode using the LG-701 “Cardamon” device (radiation power: 600 W; laser beam movement speeds: 20, 15, 10, and 5 mm/s). The hardness and microhardness of the samples were measured. Wear tests of the wheel steel samples, after different laser irradiation modes, were conducted on the “SMC-2” testing machine using the rolling with slipping method. The research was carried out using a Neophot-31 optical microscope, as well as X-ray structural analysis. Findings. According to the analysis of literary sources, the feasibility of locally strengthening the cove zone of the tread through laser treatment has been demonstrated. Based on a study of railway wheels worn during operation, which exhibit different tread profiles, it has been shown that intense plastic shear flow under high contact stress conditions leads to accelerated wear in the cove zone. This wear can result in the undercutting of the wheel flanges. Originality. It has been shown that during laser processing in continuous radiation mode, it is possible to obtain a microcomposite bainitic structure in the laser-strengthened layer, which is favorable under operating conditions. At the same time, the characteristics of the strengthened layer – such as the fine steel structure, microhardness, and hardness – can be varied within certain limits depending on the initial state of the wheel steel and the parameters of the continuous laser exposure. A comparative analysis demonstrates that both the laser processing parameters and the degree of dispersion in the initial microstructure significantly influence the effect of laser strengthening on wheel steel. A promising processing mode, involving a laser beam power of 600 W and a speed of its movement of 5–15 mm/s, is proposed and is recommended for use, particularly in combination with traditional heat treatment. Practical value. The prospects of local laser processing of the wheel tread to obtain a microcomposite bainitic structure using continuous laser radiation are discussed. This approach not only increases the wear resistance of railway wheel treads but also reduces the risk of crest undercutting during operation. This treatment can be applied both to new railway wheels after traditional heat treatment and during the restoration of worn tread profiles by regrinding in railway depots.

  • Influence of temperature-deformation parameters of thermomechanical treatment on the structure and mechanical properties of low-carbon alloy steel

    by E. V. Parusov, I.M. Chuiko, S.I. Gubenko, Prydniprovska State Academy of Civil Engineering and Architecture, E. V. Oliinyk, O. V. Parusov

    The influence of thermomechanical treatment conditions on the structure and mechanical properties of low-carbon alloyed CrMoV1Si steel (analogue Sv-08KhGSMFA steel) was analy¬zed. The obtained dependences of hardness, yield strength, and ultimate tensile strength on the thermomechanical treatment parameters made it possible to determine the optimal temperature range for the finishing of hot deformation of wire rod from the studied steel from the point of view of the metal maximum softening under the stationary mode condition of its post-deformation cooling (1050–1100°С). The mechanisms of structural transformations in hot-deformed steel are assessed and their influence on the formation of indicators of the mechanical properties of the metal after cooling is substantiated. The determined temperature range for the finishing of hot deformation is an important technological parameter in the development and implementation of the mode of softening thermomechanical treatment of steel wire rod on the Stelmor two-stage water-air cooling line.