Svetlana Gubenko
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Svetlana Gubenko has a total of 37 co-authors. Here are the top co-authors by number of shared publications:
- Eduard Parusov
Iron and Steel Institute of Z. I. Nekrasov National Academy of Sciences of Ukraine
18 shared publications - I. M. Chuiko
Nekrasov Iron and Steel Institute, National Academy of Sciences of Ukraine, Dnipro, Ukraine
11 shared publications - O. V. Parusov
Nekrasov Iron and Steel Institute, National Academy of Sciences of Ukraine, Dnipro, Ukraine
8 shared publications V. V. Sobolev
State Mining University of Ukraine, Prospekt K. Marksa 19, Dnepropetrovsk 320600, Ukraine
4 shared publicationsIron and Steel Institute of Z. I. Nekrasov National Academy of Sciences of Ukraine
3 shared publicationsPrydniprovska State Academy of Civil Engineering and Architecture
3 shared publications
Latest Publications
- 23 July 2026
- Published by Springer Nature in Materials Science
Features of crack growth near the non-metallic inclusions in steel
- 23 July 2026
- Published by Springer Nature in Materials Science
Features of crack growth near the non-metallic inclusions in steel
- 22 July 2026
- Published by National Academy of Sciences of Ukraine (Co. LTD Ukrinformnauka) (Publications) in Physicochemical Mechanics of Materials
- Vol. 62 (3) , 141-146
Influence of laser processing of steels on the sizes of nonmetallic inclusions in a strenghened layer
Specific features of the influence of laser processing on the sizes and volume fraction of non-metallic inclusions of various types in the strengthened layer of steels are studied. Laser processing of steels allows us to reduce the average size of non-metallic inclusions and the contamination of steel with inclusions in the strengthened zone by 30–50%. For different types of inclusions and steels, parameters which characterize the average sizes of inclusions and their volume fraction in the strengthened layer depending on the laser exposure effect are determined. The mechanisms and features of the transformation of non-metallic inclu¬sions during laser exposure, which contribute to a reduction in their size (crushing during partial dissolution and melting, mechanical crushing of solid or liquid initial inclusions, formation of dispersed “satellite” particles in microcomposite saturation zones of the steel matrix near the initial inclusions) are discussed.
- 22 July 2026
- Published by National Academy of Sciences of Ukraine (Co. LTD Ukrinformnauka) (Publications) in Physicochemical Mechanics of Materials
- Vol. 62 (3) , 141-146
Influence of laser processing of steels on the sizes of nonmetallic inclusions in a strenghened layer
Specific features of the influence of laser processing on the sizes and volume fraction of non-metallic inclusions of various types in the strengthened layer of steels are studied. Laser processing of steels allows us to reduce the average size of non-metallic inclusions and the contamination of steel with inclusions in the strengthened zone by 30–50%. For different types of inclusions and steels, parameters which characterize the average sizes of inclusions and their volume fraction in the strengthened layer depending on the laser exposure effect are determined. The mechanisms and features of the transformation of non-metallic inclu¬sions during laser exposure, which contribute to a reduction in their size (crushing during partial dissolution and melting, mechanical crushing of solid or liquid initial inclusions, formation of dispersed “satellite” particles in microcomposite saturation zones of the steel matrix near the initial inclusions) are discussed.
- 30 May 2026
- Published by Institute of Ferrous Metallurgy Z.I. Nekrasova of the National Academy of Sciences of Ukraine in Fundamental and applied problems of ferrous metallurgy
- No. 40,p. 56-78
Features of the transformation of heterophase non-metallic inclusions during hot and cold rolling of steels. Part 1
The behavior of microcomposite heterophase inclusions of the types “refractory phase encased in a fusible shell” and “phases are beside” during hot and cold rolling of steels has been investigated. It is demonstrated that their deformation behavior is governed by the complex interaction of the constituent phases within the inclusions, as well as by the interactions across the inclusion–matrix interfaces and the internal interphase boundaries inside the inclusions. The study establishes that these inclusions exhibit characteristic patterns of deformation processes determined by their chemical and phase composition, structure, deformability of the inclusion phases, and deformation temperature. The mutual influence of the phases on their joint deformation under hot and cold rolling conditions has been identified. It is shown that the morphological evolution of inclusions of the “refractory phase encased in a fusible shell” type during hot rolling is controlled by the plasticity of the shell phase and the complex interphase interactions resulting from interfacial friction and slip. The encapsulation of undeformable inclusions such as oxides, spinels, titanium nitride, and others within a plastic silicate or sulfide shell can be regarded as an effective mechanism for reducing the brittleness of nonmetallic inclusions during hot rolling. The shape evolution of “phases are beside” inclusions during hot rolling is determined by the plasticity of the inclusion phases and by complex interphase interactions arising from interfacial friction and slip (provided a plastic phase is present). During cold rolling, the morphological evolution of “refractory phase encased in a fusible shell” inclusions is controlled by the plasticity of the sulfide shell phase, together with complex interphase interactions involving interfacial friction and cold slip along interphase boundaries inside the inclusions. In the case of “phases are beside” inclusions, their shape change during cold rolling is governed by the plasticity of the sulfide phase (if present), as well as by interfacial friction and cold slip processes. The role of plastic phases in inclusions of both types has been clarified. It is demonstrated that plastic phases and interphase boundaries play a decisive role in the morphological evolution of heterophase inclusions of the “refractory phase encased in a fusible shell” and “phases are beside” types during hot and cold rolling of steels.
- 30 May 2026
- Published by Institute of Ferrous Metallurgy Z.I. Nekrasova of the National Academy of Sciences of Ukraine in Fundamental and applied problems of ferrous metallurgy
- No. 40,p. 56-78
Features of the transformation of heterophase non-metallic inclusions during hot and cold rolling of steels. Part 1
The behavior of microcomposite heterophase inclusions of the types “refractory phase encased in a fusible shell” and “phases are beside” during hot and cold rolling of steels has been investigated. It is demonstrated that their deformation behavior is governed by the complex interaction of the constituent phases within the inclusions, as well as by the interactions across the inclusion–matrix interfaces and the internal interphase boundaries inside the inclusions. The study establishes that these inclusions exhibit characteristic patterns of deformation processes determined by their chemical and phase composition, structure, deformability of the inclusion phases, and deformation temperature. The mutual influence of the phases on their joint deformation under hot and cold rolling conditions has been identified. It is shown that the morphological evolution of inclusions of the “refractory phase encased in a fusible shell” type during hot rolling is controlled by the plasticity of the shell phase and the complex interphase interactions resulting from interfacial friction and slip. The encapsulation of undeformable inclusions such as oxides, spinels, titanium nitride, and others within a plastic silicate or sulfide shell can be regarded as an effective mechanism for reducing the brittleness of nonmetallic inclusions during hot rolling. The shape evolution of “phases are beside” inclusions during hot rolling is determined by the plasticity of the inclusion phases and by complex interphase interactions arising from interfacial friction and slip (provided a plastic phase is present). During cold rolling, the morphological evolution of “refractory phase encased in a fusible shell” inclusions is controlled by the plasticity of the sulfide shell phase, together with complex interphase interactions involving interfacial friction and cold slip along interphase boundaries inside the inclusions. In the case of “phases are beside” inclusions, their shape change during cold rolling is governed by the plasticity of the sulfide phase (if present), as well as by interfacial friction and cold slip processes. The role of plastic phases in inclusions of both types has been clarified. It is demonstrated that plastic phases and interphase boundaries play a decisive role in the morphological evolution of heterophase inclusions of the “refractory phase encased in a fusible shell” and “phases are beside” types during hot and cold rolling of steels.
- 16 December 2025
- Published by National Academy of Sciences of Ukraine (Co. LTD Ukrinformnauka) (Publications) in Physicochemical Mechanics of Materials
- Vol. 61 (6) , 70-76
Features of crack growth at the non-metallic inclusions in steels
The features of crack propagation near non-metallic inclusions of different types, as well as possible methods of retardation of their growth by changing loading conditions and applying various treatments, are established for various steels. It is shown that the propagation of cracks is accompanied by their branching on destroyed inclusions and in their clusters, as well as on structural defects of the steel matrix. It is established that plastic sulfide inclusions, localization of relaxation processes in the steel matrix, and changes in the stress state near the inclusion under various loading conditions can retard crack propagation. The effect of local microcomposite structures in the steel matrix obtained by high-energy treatments on the features of crack propagation and retardation near non-metallic inclusions is shown.
- 16 December 2025
- Published by National Academy of Sciences of Ukraine (Co. LTD Ukrinformnauka) (Publications) in Physicochemical Mechanics of Materials
- Vol. 61 (6) , 70-76
Features of crack growth at the non-metallic inclusions in steels
The features of crack propagation near non-metallic inclusions of different types, as well as possible methods of retardation of their growth by changing loading conditions and applying various treatments, are established for various steels. It is shown that the propagation of cracks is accompanied by their branching on destroyed inclusions and in their clusters, as well as on structural defects of the steel matrix. It is established that plastic sulfide inclusions, localization of relaxation processes in the steel matrix, and changes in the stress state near the inclusion under various loading conditions can retard crack propagation. The effect of local microcomposite structures in the steel matrix obtained by high-energy treatments on the features of crack propagation and retardation near non-metallic inclusions is shown.
- Open Access
- 2 October 2025
- Published by Zeal Press in Journal of Material Science and Technology Research
- Vol. 10, 19-26
About Wave Nature of the Formation of Gradient and Microcomposite Zones Near Non-Metallic Inclusions During Laser Processing of the Steels
The goal of this investigation was to research the wave nature of the formation of gradient and composite zones near non-metallic inclusions during laser treatment of the steels. The materials for investigation were commercial steels containing different non-metallic inclusions. The specimens of different steels were exposed to laser beaming on the installations GOS-30M. The research methods were applied: petrography, X-ray microscopy (MS-46 Cameca, "Nanolab - 7") and optical microscopy (Neophot-31) to study steel matrix near non-metallic inclusions and to identify of the inclusions. Nanohardness of the steel matrix near inclusions ("Nano Indenter II") was analyzed. Peculiarities of wave saturation of the steel matrix by chemical elements of non-metallic inclusions during laser action were investigated. It was shown the role of wave relaxation of stresses in the formation of cascade type structure of steel matrix near non-metallic inclusions. The features of the formation of gradient and micro composite saturation zones of cascade type in a steel matrix under conditions of abnormal mass transfer from nonmetallic inclusions during laser processing are discussed. It has been established that the formation of gradient saturation zones with a cascade and “spot” distribution of elements and nanohardness is due to the wave nature of the relaxation of thermal and deformation stresses near non-metallic inclusions at the time of laser exposure. The difference in the rates of abnormal mass transfer of chemical elements of non-metallic inclusions into a steel matrix at the moment of laser melting is shown, which is associated with different solubility and mobility of the atoms of alloying elements in liquid iron.
- 2 October 2025
- Published by Zeal Press in Journal of Material Science and Technology Research
- Vol. 10, 19-26
Open AccessAbout Wave Nature of the Formation of Gradient and Microcomposite Zones Near Non-Metallic Inclusions During Laser Processing of the Steels
The goal of this investigation was to research the wave nature of the formation of gradient and composite zones near non-metallic inclusions during laser treatment of the steels. The materials for investigation were commercial steels containing different non-metallic inclusions. The specimens of different steels were exposed to laser beaming on the installations GOS-30M. The research methods were applied: petrography, X-ray microscopy (MS-46 Cameca, "Nanolab - 7") and optical microscopy (Neophot-31) to study steel matrix near non-metallic inclusions and to identify of the inclusions. Nanohardness of the steel matrix near inclusions ("Nano Indenter II") was analyzed. Peculiarities of wave saturation of the steel matrix by chemical elements of non-metallic inclusions during laser action were investigated. It was shown the role of wave relaxation of stresses in the formation of cascade type structure of steel matrix near non-metallic inclusions. The features of the formation of gradient and micro composite saturation zones of cascade type in a steel matrix under conditions of abnormal mass transfer from nonmetallic inclusions during laser processing are discussed. It has been established that the formation of gradient saturation zones with a cascade and “spot” distribution of elements and nanohardness is due to the wave nature of the relaxation of thermal and deformation stresses near non-metallic inclusions at the time of laser exposure. The difference in the rates of abnormal mass transfer of chemical elements of non-metallic inclusions into a steel matrix at the moment of laser melting is shown, which is associated with different solubility and mobility of the atoms of alloying elements in liquid iron.
- Open Access
- 30 September 2025
- Published by Ukrainian State University of Science and Technologies in Theory and practice of metallurgy
- No. 3,p. 90-97
Development of a method for laser strengthening of railway wheel tread
The goal of this work was to develop a method for laser strengthening of the cove zone of railway wheels in order to obtain a bainitic structure and eliminate undercutting of the crests. Methodology. Laser irradiation of the samples was performed in continuous radiation mode using the LG-701 “Cardamon” device (radiation power: 600 W; laser beam movement speeds: 20, 15, 10, and 5 mm/s). The hardness and microhardness of the samples were measured. Wear tests of the wheel steel samples, after different laser irradiation modes, were conducted on the “SMC-2” testing machine using the rolling with slipping method. The research was carried out using a Neophot-31 optical microscope, as well as X-ray structural analysis. Findings. According to the analysis of literary sources, the feasibility of locally strengthening the cove zone of the tread through laser treatment has been demonstrated. Based on a study of railway wheels worn during operation, which exhibit different tread profiles, it has been shown that intense plastic shear flow under high contact stress conditions leads to accelerated wear in the cove zone. This wear can result in the undercutting of the wheel flanges. Originality. It has been shown that during laser processing in continuous radiation mode, it is possible to obtain a microcomposite bainitic structure in the laser-strengthened layer, which is favorable under operating conditions. At the same time, the characteristics of the strengthened layer – such as the fine steel structure, microhardness, and hardness – can be varied within certain limits depending on the initial state of the wheel steel and the parameters of the continuous laser exposure. A comparative analysis demonstrates that both the laser processing parameters and the degree of dispersion in the initial microstructure significantly influence the effect of laser strengthening on wheel steel. A promising processing mode, involving a laser beam power of 600 W and a speed of its movement of 5–15 mm/s, is proposed and is recommended for use, particularly in combination with traditional heat treatment. Practical value. The prospects of local laser processing of the wheel tread to obtain a microcomposite bainitic structure using continuous laser radiation are discussed. This approach not only increases the wear resistance of railway wheel treads but also reduces the risk of crest undercutting during operation. This treatment can be applied both to new railway wheels after traditional heat treatment and during the restoration of worn tread profiles by regrinding in railway depots.
- 30 September 2025
- Published by Ukrainian State University of Science and Technologies in Theory and practice of metallurgy
- No. 3,p. 90-97
Open AccessDevelopment of a method for laser strengthening of railway wheel tread
The goal of this work was to develop a method for laser strengthening of the cove zone of railway wheels in order to obtain a bainitic structure and eliminate undercutting of the crests. Methodology. Laser irradiation of the samples was performed in continuous radiation mode using the LG-701 “Cardamon” device (radiation power: 600 W; laser beam movement speeds: 20, 15, 10, and 5 mm/s). The hardness and microhardness of the samples were measured. Wear tests of the wheel steel samples, after different laser irradiation modes, were conducted on the “SMC-2” testing machine using the rolling with slipping method. The research was carried out using a Neophot-31 optical microscope, as well as X-ray structural analysis. Findings. According to the analysis of literary sources, the feasibility of locally strengthening the cove zone of the tread through laser treatment has been demonstrated. Based on a study of railway wheels worn during operation, which exhibit different tread profiles, it has been shown that intense plastic shear flow under high contact stress conditions leads to accelerated wear in the cove zone. This wear can result in the undercutting of the wheel flanges. Originality. It has been shown that during laser processing in continuous radiation mode, it is possible to obtain a microcomposite bainitic structure in the laser-strengthened layer, which is favorable under operating conditions. At the same time, the characteristics of the strengthened layer – such as the fine steel structure, microhardness, and hardness – can be varied within certain limits depending on the initial state of the wheel steel and the parameters of the continuous laser exposure. A comparative analysis demonstrates that both the laser processing parameters and the degree of dispersion in the initial microstructure significantly influence the effect of laser strengthening on wheel steel. A promising processing mode, involving a laser beam power of 600 W and a speed of its movement of 5–15 mm/s, is proposed and is recommended for use, particularly in combination with traditional heat treatment. Practical value. The prospects of local laser processing of the wheel tread to obtain a microcomposite bainitic structure using continuous laser radiation are discussed. This approach not only increases the wear resistance of railway wheel treads but also reduces the risk of crest undercutting during operation. This treatment can be applied both to new railway wheels after traditional heat treatment and during the restoration of worn tread profiles by regrinding in railway depots.
- 1 July 2025
- Published by Springer Nature in Materials Science
- Vol. 61 (1) , 42-49
Influence of temperature-deformation parameters of thermomechanical treatment on the structure and mechanical properties of low-carbon alloyed steel
- 1 July 2025
- Published by Springer Nature in Materials Science
- Vol. 61 (1) , 42-49
Influence of temperature-deformation parameters of thermomechanical treatment on the structure and mechanical properties of low-carbon alloyed steel
- 28 February 2025
- Published by National Academy of Sciences of Ukraine (Co. LTD Ukrinformnauka) (Publications) in Physicochemical Mechanics of Materials
- Vol. 61 (1) , 44-51
Influence of temperature-deformation parameters of thermomechanical treatment on the structure and mechanical properties of low-carbon alloy steel
The influence of thermomechanical treatment conditions on the structure and mechanical properties of low-carbon alloyed CrMoV1Si steel (analogue Sv-08KhGSMFA steel) was analy¬zed. The obtained dependences of hardness, yield strength, and ultimate tensile strength on the thermomechanical treatment parameters made it possible to determine the optimal temperature range for the finishing of hot deformation of wire rod from the studied steel from the point of view of the metal maximum softening under the stationary mode condition of its post-deformation cooling (1050–1100°С). The mechanisms of structural transformations in hot-deformed steel are assessed and their influence on the formation of indicators of the mechanical properties of the metal after cooling is substantiated. The determined temperature range for the finishing of hot deformation is an important technological parameter in the development and implementation of the mode of softening thermomechanical treatment of steel wire rod on the Stelmor two-stage water-air cooling line.
- 28 February 2025
- Published by National Academy of Sciences of Ukraine (Co. LTD Ukrinformnauka) (Publications) in Physicochemical Mechanics of Materials
- Vol. 61 (1) , 44-51
Influence of temperature-deformation parameters of thermomechanical treatment on the structure and mechanical properties of low-carbon alloy steel
The influence of thermomechanical treatment conditions on the structure and mechanical properties of low-carbon alloyed CrMoV1Si steel (analogue Sv-08KhGSMFA steel) was analy¬zed. The obtained dependences of hardness, yield strength, and ultimate tensile strength on the thermomechanical treatment parameters made it possible to determine the optimal temperature range for the finishing of hot deformation of wire rod from the studied steel from the point of view of the metal maximum softening under the stationary mode condition of its post-deformation cooling (1050–1100°С). The mechanisms of structural transformations in hot-deformed steel are assessed and their influence on the formation of indicators of the mechanical properties of the metal after cooling is substantiated. The determined temperature range for the finishing of hot deformation is an important technological parameter in the development and implementation of the mode of softening thermomechanical treatment of steel wire rod on the Stelmor two-stage water-air cooling line.
- 1 January 2025
- Published by Springer Nature in Materials Science
- Vol. 60 (4) , 462-469
The influence of boride inclusions on the structure and properties of 04Kh14T3R1F steel intended for covers of spent fuel cassettes of nuclear power plants
- 1 January 2025
- Published by Springer Nature in Materials Science
- Vol. 60 (4) , 462-469
The influence of boride inclusions on the structure and properties of 04Kh14T3R1F steel intended for covers of spent fuel cassettes of nuclear power plants
- 1 November 2024
- Published by Springer Nature in Materials Science
- Vol. 60 (3) , 367-374
Evolution of nonmetallic inclusions during hot rolling of steels
- 1 November 2024
- Published by Springer Nature in Materials Science
- Vol. 60 (3) , 367-374
Evolution of nonmetallic inclusions during hot rolling of steels