Xuan Hoa Thi Pham
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Xuan Hoa Thi Pham has a total of 8 co-authors. Here are the top co-authors by number of shared publications:
- Hien-Thanh Le
Ho Chi Minh City University of Industry and Trade, Vietnam
2 shared publications Dinh‐Nhon Truong
Faculty of International Education Ho Chi Minh City University of Technology and Education Ho Chi Minh City Vietnam
1 shared publicationHai Van Tran
Faculty of Electrical and Electronics Engineering University of Food Industry Ho Chi Minh City Vietnam
1 shared publication- Hai Van Tran
Ho Chi Minh City University of Industry and Trade, Vietnam
1 shared publication - Hai Van Tran1 shared publication
Nam Xuan Doan
Faculty of Electrical and Electronics Engineering University of Food Industry Ho Chi Minh City Vietnam
1 shared publication
Latest Publications
- Open Access
- 1 June 2026
- Published by Institute of Advanced Engineering and Science in International Journal of Power Electronics and Drive Systems (IJPEDS)
- Vol. 17 (2)
Innovative frequency and voltage controller for AC microgrid
This paper designs a power controller for power converters using fuzzy logic. The proposed controller will automatically adjust the frequency and voltage when the load changes to improve the power quality of the microgrid. Besides, the controller can realize accurate power sharing among the power converters in the microgrid, thereby suppressing the circulating current between the inverters. Furthermore, to ensure the control system operates stably and accurately during voltage and frequency adjustments, this paper employs a sliding-mode controller rather than a conventional proportional-integral controller. The proposed control method has a voltage deviation from the rated value when the load changes in the range of 1.5 Volts to 2.7 volts, and a frequency deviation from the rated value when the load changes in the range of 0.2 to 0.4 Hz. The accuracy of reactive power division is 100%. The proposed controller is simulated using MATLAB/ Simulink software, and the results obtained from the simulation have verified the effectiveness of the proposed method.
- 1 June 2026
- Published by Institute of Advanced Engineering and Science in International Journal of Power Electronics and Drive Systems (IJPEDS)
- Vol. 17 (2)
Open AccessInnovative frequency and voltage controller for AC microgrid
This paper designs a power controller for power converters using fuzzy logic. The proposed controller will automatically adjust the frequency and voltage when the load changes to improve the power quality of the microgrid. Besides, the controller can realize accurate power sharing among the power converters in the microgrid, thereby suppressing the circulating current between the inverters. Furthermore, to ensure the control system operates stably and accurately during voltage and frequency adjustments, this paper employs a sliding-mode controller rather than a conventional proportional-integral controller. The proposed control method has a voltage deviation from the rated value when the load changes in the range of 1.5 Volts to 2.7 volts, and a frequency deviation from the rated value when the load changes in the range of 0.2 to 0.4 Hz. The accuracy of reactive power division is 100%. The proposed controller is simulated using MATLAB/ Simulink software, and the results obtained from the simulation have verified the effectiveness of the proposed method.
- 9 October 2025
- Published by Springer Nature in Journal of Electrical Engineering & Technology
- Vol. 21 (1) , 1083-1097
An Improved Controller for AC/DC Hybrid Microgrid Using Bidirectional Interlinking Converter
- 9 October 2025
- Published by Springer Nature in Journal of Electrical Engineering & Technology
- Vol. 21 (1) , 1083-1097
An Improved Controller for AC/DC Hybrid Microgrid Using Bidirectional Interlinking Converter
- 11 June 2025
- Published by Springer Nature in Journal of Power Electronics
- Vol. 26 (2) , 406-419
Adaptive power controller for AC/DC hybrid microgrids
- 11 June 2025
- Published by Springer Nature in Journal of Power Electronics
- Vol. 26 (2) , 406-419
Adaptive power controller for AC/DC hybrid microgrids
- Open Access
- 1 January 2025
- Published by Wiley in International Transactions on Electrical Energy Systems
- Vol. 2025 (1)
Reducing One‐Year Energy Loss for the Hoang Dieu 26‐Node Distribution Power Network in Vietnam Through Optimal Placement of Solar‐Powered Distributed Generators
This research investigates the application of the parrot optimizer (PO) algorithm and the artemisinin optimization (AO) algorithm to determine the optimal placement of solar‐powered distributed generators (SP‐DGs) within the standard IEEE 33‐node, 69‐node, and the Vietnamese Hoang Dieu 26‐node distribution power networks (DPNs). Both algorithms were implemented to minimize active power loss under peak load conditions for a one‐hour period. The optimal placement problem was analyzed for two scenarios of renewable‐based distributed generation (RBDG) operation: Case 1 (pure active power generation) and Case 2 (active and reactive power generation). The performance of the two algorithms was compared against previous studies to identify a more effective approach. Furthermore, the AO algorithm was applied to minimize the total one‐year energy loss (OYEL) in the Hoang Dieu 26‐node DPN, utilizing real solar radiation data for Hoang Dieu Street in Ho Chi Minh City, Vietnam, obtained from a solar global atlas. The findings indicate that AO demonstrates superior effectiveness compared to PO and certain existing algorithms for the two standard DPNs. For the Hoang Dieu 26‐node DPN, AO achieved significant reductions in OYEL, suggesting its suitability for optimally placing and operating RBDGs to yield substantial benefits for this specific network.
- 1 January 2025
- Published by Wiley in International Transactions on Electrical Energy Systems
- Vol. 2025 (1)
Open AccessReducing One‐Year Energy Loss for the Hoang Dieu 26‐Node Distribution Power Network in Vietnam Through Optimal Placement of Solar‐Powered Distributed Generators
This research investigates the application of the parrot optimizer (PO) algorithm and the artemisinin optimization (AO) algorithm to determine the optimal placement of solar‐powered distributed generators (SP‐DGs) within the standard IEEE 33‐node, 69‐node, and the Vietnamese Hoang Dieu 26‐node distribution power networks (DPNs). Both algorithms were implemented to minimize active power loss under peak load conditions for a one‐hour period. The optimal placement problem was analyzed for two scenarios of renewable‐based distributed generation (RBDG) operation: Case 1 (pure active power generation) and Case 2 (active and reactive power generation). The performance of the two algorithms was compared against previous studies to identify a more effective approach. Furthermore, the AO algorithm was applied to minimize the total one‐year energy loss (OYEL) in the Hoang Dieu 26‐node DPN, utilizing real solar radiation data for Hoang Dieu Street in Ho Chi Minh City, Vietnam, obtained from a solar global atlas. The findings indicate that AO demonstrates superior effectiveness compared to PO and certain existing algorithms for the two standard DPNs. For the Hoang Dieu 26‐node DPN, AO achieved significant reductions in OYEL, suggesting its suitability for optimally placing and operating RBDGs to yield substantial benefits for this specific network.
- Open Access
- 28 December 2024
- Published by Ho Chi Minh City University of Technology and Engineering in Journal of Technical Education Science
- Vol. 19 (06) , 45-55
The Controller Improves Voltage Quality In Microgrids
The inverters in the microgrid are connected in parallel to improve efficiency. When the Microgrid is operating in standalone mode, the inverters must be controlled to share their power to stabilize the frequency and voltage. The droop control method is one of the most popular power-sharing methods today, some studies have presented traditional and improved droop control methods. However, the purpose of the studies is power-sharing for the inverters that no purpose of reducing the voltage and frequency deviation to improve power quality. This paper presents a voltage and frequency adjustment method based on fuzzy logic to minimize voltage and frequency deviation to improve power quality in microgrids. This controller includes a Droop controller combined with fuzzy logic, the fuzzy logic block will control to change in the slope of the Droop characteristic curve when the load changes. The purpose of the proposed method is to improve the accuracy of power-sharing for inverters and at the same time minimize voltage and frequency deviations in microgrids. Simulation results will prove the effectiveness of the proposed method.
- 28 December 2024
- Published by Ho Chi Minh City University of Technology and Engineering in Journal of Technical Education Science
- Vol. 19 (06) , 45-55
Open AccessThe Controller Improves Voltage Quality In Microgrids
The inverters in the microgrid are connected in parallel to improve efficiency. When the Microgrid is operating in standalone mode, the inverters must be controlled to share their power to stabilize the frequency and voltage. The droop control method is one of the most popular power-sharing methods today, some studies have presented traditional and improved droop control methods. However, the purpose of the studies is power-sharing for the inverters that no purpose of reducing the voltage and frequency deviation to improve power quality. This paper presents a voltage and frequency adjustment method based on fuzzy logic to minimize voltage and frequency deviation to improve power quality in microgrids. This controller includes a Droop controller combined with fuzzy logic, the fuzzy logic block will control to change in the slope of the Droop characteristic curve when the load changes. The purpose of the proposed method is to improve the accuracy of power-sharing for inverters and at the same time minimize voltage and frequency deviations in microgrids. Simulation results will prove the effectiveness of the proposed method.
- Open Access
- 28 December 2024
- Published by Ho Chi Minh City University of Technology and Engineering in Journal of Technical Education Science
- Vol. 19 (06) , 95-105
Improved Controller for Interlinking Converter in Hybrid AC/DC Microgrids
The AC/DC hybrid microgrids are a feasible solution to provide both AC and DC power to electrical equipment. However, the control problem to maintain voltage and frequency stability in AC/DC hybrid microgrids is essential. This paper proposes a control method for the converter to maintain voltage and frequency stability for AC/DC hybrid microgrids. The power converter will operate bidirectionally to transfer power back and forth between AC and DC subgrids in the AC/DC hybrid microgrid operating in standalone mode. The proposed control method not only controls the bidirectional power flow between AC and DC subgrids to stabilize voltage and frequency as well as balance active power and reactive power. In addition, the proposed method can restore voltage and frequency for the microgrid in the event of sudden load surges or power failures in AC and DC subgrids. This method is established based on the relationship between active power and frequency, because active power is present in both AC and DC subgrids, while frequency is only present in AC subgrid. However, in AC subgrid, frequency depends on active power, while in DC subgrid, DC bus voltage depends on active power. Therefore, the proposed method is designed based on adaptive frequency shifting to adjust the power flow exchange between the two subgrids in order to maintain the stability of the frequency and voltage of the buses. The suitability and feasibility of the method are demonstrated by simulating the AC/DC hybrid microgrid using Matlab/simulink software.
- 28 December 2024
- Published by Ho Chi Minh City University of Technology and Engineering in Journal of Technical Education Science
- Vol. 19 (06) , 95-105
Open AccessImproved Controller for Interlinking Converter in Hybrid AC/DC Microgrids
The AC/DC hybrid microgrids are a feasible solution to provide both AC and DC power to electrical equipment. However, the control problem to maintain voltage and frequency stability in AC/DC hybrid microgrids is essential. This paper proposes a control method for the converter to maintain voltage and frequency stability for AC/DC hybrid microgrids. The power converter will operate bidirectionally to transfer power back and forth between AC and DC subgrids in the AC/DC hybrid microgrid operating in standalone mode. The proposed control method not only controls the bidirectional power flow between AC and DC subgrids to stabilize voltage and frequency as well as balance active power and reactive power. In addition, the proposed method can restore voltage and frequency for the microgrid in the event of sudden load surges or power failures in AC and DC subgrids. This method is established based on the relationship between active power and frequency, because active power is present in both AC and DC subgrids, while frequency is only present in AC subgrid. However, in AC subgrid, frequency depends on active power, while in DC subgrid, DC bus voltage depends on active power. Therefore, the proposed method is designed based on adaptive frequency shifting to adjust the power flow exchange between the two subgrids in order to maintain the stability of the frequency and voltage of the buses. The suitability and feasibility of the method are demonstrated by simulating the AC/DC hybrid microgrid using Matlab/simulink software.
- Open Access
- 15 May 2023
- Published by Institution of Engineering and Technology (IET) in The Journal of Engineering
- Vol. 2023 (5)
Power control in microgrid using improved virtual impedance method
In this article, a method is proposed to increase the accuracy of reactive power‐sharing for parallel‐connected inverters in Microgrid, this method is done by automatically adjusting the values of the virtual impedance to adjusting the output voltage of the inverters. The virtual impedances are automatically adjusted to compensate for the difference in the output voltage of the inverters due to the influence of the line impedances. The output voltage of the inverters will be adaptively adjusted according to the change of the load, this method greatly improves the accuracy in the reactive power sharing The correct power sharing for the inverters will ensure the stability of voltage and frequency in the Microgrid. The control method is simple and does not need to know the line impedance parameter. The feasibility and effectiveness of the proposed strategy are proven by simulation and experimental results.
- 15 May 2023
- Published by Institution of Engineering and Technology (IET) in The Journal of Engineering
- Vol. 2023 (5)
Open AccessPower control in microgrid using improved virtual impedance method
In this article, a method is proposed to increase the accuracy of reactive power‐sharing for parallel‐connected inverters in Microgrid, this method is done by automatically adjusting the values of the virtual impedance to adjusting the output voltage of the inverters. The virtual impedances are automatically adjusted to compensate for the difference in the output voltage of the inverters due to the influence of the line impedances. The output voltage of the inverters will be adaptively adjusted according to the change of the load, this method greatly improves the accuracy in the reactive power sharing The correct power sharing for the inverters will ensure the stability of voltage and frequency in the Microgrid. The control method is simple and does not need to know the line impedance parameter. The feasibility and effectiveness of the proposed strategy are proven by simulation and experimental results.
- Open Access
- 7 May 2022
- Published by Institution of Engineering and Technology (IET) in The Journal of Engineering
- Vol. 2022 (8) , 773-787
Improved power controller for enhancement of voltage quality in microgrid
In microgrid, non‐linear or unbalanced loads will degrade the voltage quality at the output of the inverters, and the voltage of the load will be distorted or unbalanced. On the other hand, the inverters in microgrid are connected in parallel to improve efficiency, increase transmission capacity, and are easy to repair and maintain. When the microgrid is operating in standalone mode, inverters must be controlled to share power according to their rated power; this is to stabilize frequency and voltage in the microgrid. However, since non‐linear or unbalanced loads will produce load currents containing harmonics, it will make the voltage of load unbalanced, which will affect the control of power‐sharing for the inverters, and it also degrades the voltage quality at the output of the inverters. This paper has proposed an improved power‐sharing control method combined with the sliding mode control (SMC) technique to improve the voltage quality and improve the accuracy of power‐sharing for the inverters in the microgrid. The proposed method will ensure accurate power‐sharing even if the communication is interrupted. If the load changes while the communication is interrupted, the accuracy of power‐sharing is reduced but the proposed method is better than the conventional power‐sharing method. In addition, the accuracy of the proposed power‐sharing method is not affected by the time delay in the communication channel and local loads at the output of the inverters. Simulation and experimental results will prove the effectiveness of the proposed method.
- 7 May 2022
- Published by Institution of Engineering and Technology (IET) in The Journal of Engineering
- Vol. 2022 (8) , 773-787
Open AccessImproved power controller for enhancement of voltage quality in microgrid
In microgrid, non‐linear or unbalanced loads will degrade the voltage quality at the output of the inverters, and the voltage of the load will be distorted or unbalanced. On the other hand, the inverters in microgrid are connected in parallel to improve efficiency, increase transmission capacity, and are easy to repair and maintain. When the microgrid is operating in standalone mode, inverters must be controlled to share power according to their rated power; this is to stabilize frequency and voltage in the microgrid. However, since non‐linear or unbalanced loads will produce load currents containing harmonics, it will make the voltage of load unbalanced, which will affect the control of power‐sharing for the inverters, and it also degrades the voltage quality at the output of the inverters. This paper has proposed an improved power‐sharing control method combined with the sliding mode control (SMC) technique to improve the voltage quality and improve the accuracy of power‐sharing for the inverters in the microgrid. The proposed method will ensure accurate power‐sharing even if the communication is interrupted. If the load changes while the communication is interrupted, the accuracy of power‐sharing is reduced but the proposed method is better than the conventional power‐sharing method. In addition, the accuracy of the proposed power‐sharing method is not affected by the time delay in the communication channel and local loads at the output of the inverters. Simulation and experimental results will prove the effectiveness of the proposed method.
- 10 January 2021
- Published by Springer Nature in Electrical Engineering
- Vol. 103 (3) , 1679-1689
An improved controller for reactive power sharing in islanded microgrid
- 10 January 2021
- Published by Springer Nature in Electrical Engineering
- Vol. 103 (3) , 1679-1689
An improved controller for reactive power sharing in islanded microgrid
- 1 March 2020
- Published by Elsevier in Electric Power Systems Research
- Vol. 180
Power sharing strategy in islanded microgrids using improved droop control
- 1 March 2020
- Published by Elsevier in Electric Power Systems Research
- Vol. 180
Power sharing strategy in islanded microgrids using improved droop control