Gokul Venugopalan
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Gokul Venugopalan has a total of 28 co-authors. Here are the top co-authors by number of shared publications:
- Christopher George Arges
Argonne National Laboratory
6 shared publications - Deepra Bhattacharya
Pennsylvania State University
2 shared publications - Subarna Kole
Cain Department of Chemical Engineering, Louisiana State University, Baton Rouge, USA
2 shared publications - Ardalan Chaichi
Department of Mechanical and Industrial Engineering, Louisiana State University, Baton Rouge, Louisiana 70803, United States
1 shared publication - Bryan Pivovar
National Laboratory of the Rockies
1 shared publication Cameron Ysidron
Cain Department of Chemical Engineering, Louisiana State University, Baton Rouge, USA
1 shared publication
Latest Publications
- Open Access
- 11 March 2022
- Published by American Chemical Society (ACS) in ACS Energy Letters
- Vol. 7 (4) , 1322-1329
Electrochemical Pumping for Challenging Hydrogen Separations
- 11 March 2022
- Published by American Chemical Society (ACS) in ACS Energy Letters
- Vol. 7 (4) , 1322-1329
Open AccessElectrochemical Pumping for Challenging Hydrogen Separations
- Open Access
- 13 May 2021
- Published by Royal Society of Chemistry (RSC) in Materials Advances
- Vol. 2 (13) , 4228-4234
Correlating high temperature thin film ionomer electrode binder properties to hydrogen pump polarization
Ionomer electrode binders are important materials for polymer electrolyte membrane (PEM) fuel cells and electrolyzers and have a profound impact on cell performance. Herein, we report the effect of two different types of high-temperature (HT) ionomers, characterized as thin films (∼10 nm), on hydrogen oxidation/evolution reaction (HOR/HER) kinetics and hydrogen permeability using interdigitated electrode (IDE) platforms decorated with nanoscale platinum electrocatalysts. The two different ionomers studied were poly(tetraflurostyrene phosphonic acid-co-pentafluorostyrene) (PTFSPA) and quaternary benzyl pyridinium poly(arylene ether sulfone) imbibed with phosphoric acid (QPPSf-H3PO4). The reaction kinetics and limiting current values observed with thin film ionomers on IDEs were commensurate to the values observed in electrochemical hydrogen pumps (ECHPs) that use the ionomers as electrode binders. Using PTFSPA as the binder, an HT-PEM ECHP showed 1 A cm−2 at 55 mV when using 2 mgPt cm−2 in the membrane electrode assembly.
- 13 May 2021
- Published by Royal Society of Chemistry (RSC) in Materials Advances
- Vol. 2 (13) , 4228-4234
Open AccessCorrelating high temperature thin film ionomer electrode binder properties to hydrogen pump polarization
Ionomer electrode binders are important materials for polymer electrolyte membrane (PEM) fuel cells and electrolyzers and have a profound impact on cell performance. Herein, we report the effect of two different types of high-temperature (HT) ionomers, characterized as thin films (∼10 nm), on hydrogen oxidation/evolution reaction (HOR/HER) kinetics and hydrogen permeability using interdigitated electrode (IDE) platforms decorated with nanoscale platinum electrocatalysts. The two different ionomers studied were poly(tetraflurostyrene phosphonic acid-co-pentafluorostyrene) (PTFSPA) and quaternary benzyl pyridinium poly(arylene ether sulfone) imbibed with phosphoric acid (QPPSf-H3PO4). The reaction kinetics and limiting current values observed with thin film ionomers on IDEs were commensurate to the values observed in electrochemical hydrogen pumps (ECHPs) that use the ionomers as electrode binders. Using PTFSPA as the binder, an HT-PEM ECHP showed 1 A cm−2 at 55 mV when using 2 mgPt cm−2 in the membrane electrode assembly.
- 23 December 2020
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry A
- Vol. 9 (4) , 2223-2238
Bipolar membrane polarization behavior with systematically varied interfacial areas in the junction region
Left image is the relationship for the overpotential for water dissociation as a function of bipolar junction electric field whereas the right image presents micrographs and the procedure to make bipolar membranes with micropatterned interfaces.
- 23 December 2020
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry A
- Vol. 9 (4) , 2223-2238
Bipolar membrane polarization behavior with systematically varied interfacial areas in the junction region
Left image is the relationship for the overpotential for water dissociation as a function of bipolar junction electric field whereas the right image presents micrographs and the procedure to make bipolar membranes with micropatterned interfaces.
- 18 May 2020
- Published by American Chemical Society (ACS) in ACS Applied Energy Materials
- Vol. 3 (6) , 5693-5704
A Solid-State and Flexible Supercapacitor That Operates across a Wide Temperature Range
- 18 May 2020
- Published by American Chemical Society (ACS) in ACS Applied Energy Materials
- Vol. 3 (6) , 5693-5704
A Solid-State and Flexible Supercapacitor That Operates across a Wide Temperature Range
- 20 April 2020
- Published by American Chemical Society (ACS) in ACS Applied Energy Materials
- Vol. 3 (5) , 4787-4798
High Power Thermally Regenerative Ammonia-Copper Redox Flow Battery Enabled by a Zero Gap Cell Design, Low-Resistant Membranes, and Electrode Coatings
Thermally regenerative batteries (TRBs) is an emerging platform for extracting electrical energy from low-grade waste heat (T < 130 °C). TRBs using an ammonia-copper redox couple can store waste-heat energy in a chemical form that can be later discharged to electrical energy upon demand. Previous thermally regenerative ammonia battery (TRAB) demonstrations suffered from poor heat to electrical energy conversion efficiency when benchmarked against TEGs. In this work, we report the highest power density to date for a TRAB (280 W m-2 at 55 °C) with a 5.7× improvement in power density over conventional TRAB designs. Notably, the TRAB was configured similar to a redox flow battery setup - which is termed here an ammonia flow battery (AFB). The substantial improvement in the AFB power density translated to thermal efficiency (ηth) values as high as 2.99 % and 37.9 % relative to the Carnot efficiency (ηth/C). These values correspond to an 87.6 % improvement in ηth value over conventional TRAB designs and the highest reported ηth/C for low-grade waste heat recovery using TRABs. The excellent performance of the AFB was ascribed to a zero gap design, deploying a low-resistant, inexpensive anion exchange membrane (AEM), and implementing a copper ion selective ionomer coating on the copper mesh electrodes. The high-power AFB in this report represents a significant milestone in harvesting low-grade waste heat.
- 20 April 2020
- Published by American Chemical Society (ACS) in ACS Applied Energy Materials
- Vol. 3 (5) , 4787-4798
High Power Thermally Regenerative Ammonia-Copper Redox Flow Battery Enabled by a Zero Gap Cell Design, Low-Resistant Membranes, and Electrode Coatings
Thermally regenerative batteries (TRBs) is an emerging platform for extracting electrical energy from low-grade waste heat (T < 130 °C). TRBs using an ammonia-copper redox couple can store waste-heat energy in a chemical form that can be later discharged to electrical energy upon demand. Previous thermally regenerative ammonia battery (TRAB) demonstrations suffered from poor heat to electrical energy conversion efficiency when benchmarked against TEGs. In this work, we report the highest power density to date for a TRAB (280 W m-2 at 55 °C) with a 5.7× improvement in power density over conventional TRAB designs. Notably, the TRAB was configured similar to a redox flow battery setup - which is termed here an ammonia flow battery (AFB). The substantial improvement in the AFB power density translated to thermal efficiency (ηth) values as high as 2.99 % and 37.9 % relative to the Carnot efficiency (ηth/C). These values correspond to an 87.6 % improvement in ηth value over conventional TRAB designs and the highest reported ηth/C for low-grade waste heat recovery using TRABs. The excellent performance of the AFB was ascribed to a zero gap design, deploying a low-resistant, inexpensive anion exchange membrane (AEM), and implementing a copper ion selective ionomer coating on the copper mesh electrodes. The high-power AFB in this report represents a significant milestone in harvesting low-grade waste heat.
- 6 December 2019
- Published by American Chemical Society (ACS) in ACS Applied Energy Materials
- Vol. 3 (1) , 573-585
Stable and Highly Conductive Polycation–Polybenzimidazole Membrane Blends for Intermediate Temperature Polymer Electrolyte Membrane Fuel Cells
- 6 December 2019
- Published by American Chemical Society (ACS) in ACS Applied Energy Materials
- Vol. 3 (1) , 573-585
Stable and Highly Conductive Polycation–Polybenzimidazole Membrane Blends for Intermediate Temperature Polymer Electrolyte Membrane Fuel Cells