Wacław Skoczyński
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Wacław Skoczyński has a total of 20 co-authors. Here are the top co-authors by number of shared publications:
- Paweł Piórkowski
Faculty of Mechanical Engineering, Wroclaw University of Science and Technology, 50-370 Wroclaw, Poland
7 shared publications - Andrzej Roszkowski
Wroclaw Univ Technol & Sci, Fac Mech Engn, Lukasiewicza 5, PL-50370 Wroclaw, Poland
6 shared publications - Tomasz Jankowski
Wroclaw Univ Technol & Sci, Fac Mech Engn, Lukasiewicza 5, PL-50370 Wroclaw, Poland
5 shared publications - Marek Stembalski
Department of Machine Tools and Mechanical Technologies, Wroclaw University of Science and Technology, 50-370 Wrocław, Poland
4 shared publications - Wojciech Borkowski
Faculty of Mechanical Engineering, Wroclaw University of Science and Technology, 50-370 Wroclaw, Poland
4 shared publications - Paweł Turek
Department of Machine Tools and Mechanical Engineering Technologies, Faculty of Mechanical Engineering, Wrocław University of Science and Technology, Łukasiewicza 5, 50-371 Wrocław, Poland
3 shared publications
Latest Publications
- 9 June 2025
- Published by Wroclaw Board of Scientific Technical Societies Federation NOT in Journal of Machine Engineering
- Vol. 25 (2) , 43-63
Gear Wear Mechanisms, Monitoring Techniques and Their Potential Use in Gear Predictive Maintenance
In order to ensure the undisturbed operation of gear transmissions, avoid their unplanned downtimes and secondary damage to them, their condition needs to be monitored and their failures need to be diagnosed. Currently, there is no commercial and universal diagnostic system for predictive analysis of gear wear. There are also no limit values of wear indicators defining individual causes of wear. The article presents problems related to various mechanisms of gear wear. Different methods of monitoring the condition of the gear are presented. They are presented. Thermal methods, analysis of wear residues, and measurements and analysis of vibrations and acoustic emissions are described. The usefulness of these techniques for predictive maintenance of gear movement is indicated. It is proposed to extend gear diagnostics by using machine learning methods to detect their faults, and in particular critical states of gear wear.
- 9 June 2025
- Published by Wroclaw Board of Scientific Technical Societies Federation NOT in Journal of Machine Engineering
- Vol. 25 (2) , 43-63
Gear Wear Mechanisms, Monitoring Techniques and Their Potential Use in Gear Predictive Maintenance
In order to ensure the undisturbed operation of gear transmissions, avoid their unplanned downtimes and secondary damage to them, their condition needs to be monitored and their failures need to be diagnosed. Currently, there is no commercial and universal diagnostic system for predictive analysis of gear wear. There are also no limit values of wear indicators defining individual causes of wear. The article presents problems related to various mechanisms of gear wear. Different methods of monitoring the condition of the gear are presented. They are presented. Thermal methods, analysis of wear residues, and measurements and analysis of vibrations and acoustic emissions are described. The usefulness of these techniques for predictive maintenance of gear movement is indicated. It is proposed to extend gear diagnostics by using machine learning methods to detect their faults, and in particular critical states of gear wear.
- Open Access
- 6 October 2024
- Published by MDPI AG in Applied Sciences
- Vol. 14 (19) , 9023
Comprehensive Evaluation Method for High-Performance Milling of Inconel 718 Alloy
The aim of this paper was to develop and verify a method for evaluating the high-performance milling of Inconel 718 alloy under accelerated tool wear conditions. The method considered parameters such as cutting-force components, total machine power consumption, cutting-edge wear, and material removal rate. The study compared high-feed milling and plunge milling, using sets of cutting parameters that are appropriate for both techniques. The results indicate that high-feed milling was more efficient, achieving higher material removal rates and lower tool wear. On the other hand, plunge milling was characterized by a lower axial force component (Fz), which can positively affect machining accuracy. The paper highlights that the proposed evaluation method can also be applied to other hard-to-machine materials, and plunge milling offers a competitive alternative for roughing operations in the milling of Inconel 718 alloy.
- 6 October 2024
- Published by MDPI AG in Applied Sciences
- Vol. 14 (19) , 9023
Open AccessComprehensive Evaluation Method for High-Performance Milling of Inconel 718 Alloy
The aim of this paper was to develop and verify a method for evaluating the high-performance milling of Inconel 718 alloy under accelerated tool wear conditions. The method considered parameters such as cutting-force components, total machine power consumption, cutting-edge wear, and material removal rate. The study compared high-feed milling and plunge milling, using sets of cutting parameters that are appropriate for both techniques. The results indicate that high-feed milling was more efficient, achieving higher material removal rates and lower tool wear. On the other hand, plunge milling was characterized by a lower axial force component (Fz), which can positively affect machining accuracy. The paper highlights that the proposed evaluation method can also be applied to other hard-to-machine materials, and plunge milling offers a competitive alternative for roughing operations in the milling of Inconel 718 alloy.
- Open Access
- 1 January 2021
- Published by Wydawnictwo Naukowe Gabriel Borowski (WNGB) in Advances in Science and Technology Research Journal
- Vol. 15 (2) , 148-155
Evaluation of Milling Machine Properties Based on Shape Errors
A procedure for assessing the properties of a milling machine based on machining tests was presented, with particular emphasis on shape errors and properties of the workpiece surface layer. The selection of an appropriate test-piece and cutting parameters for such a test was discussed. A mathematical formula was also presented, which allows to associate the accuracy of the test-piece with that of the milling machine. The proposed test procedure was verified by evaluating the DMC 1035V Ecoline vertical machining centre.
- 1 January 2021
- Published by Wydawnictwo Naukowe Gabriel Borowski (WNGB) in Advances in Science and Technology Research Journal
- Vol. 15 (2) , 148-155
Open AccessEvaluation of Milling Machine Properties Based on Shape Errors
A procedure for assessing the properties of a milling machine based on machining tests was presented, with particular emphasis on shape errors and properties of the workpiece surface layer. The selection of an appropriate test-piece and cutting parameters for such a test was discussed. A mathematical formula was also presented, which allows to associate the accuracy of the test-piece with that of the milling machine. The proposed test procedure was verified by evaluating the DMC 1035V Ecoline vertical machining centre.
- Open Access
- 1 January 2021
- Published by Wydawnictwo Naukowe Gabriel Borowski (WNGB) in Advances in Science and Technology Research Journal
- Vol. 15 (1) , 283-289
Statistical Testing of Milled Objects on Numerically Controlled Three-Axis Milling Machines
Statistical studies of the surface distribution of milled workpieces and the possibility of their use for operation-based tests and machine tool evaluation were presented. In the first part of the paper, the assumptions and scope of statistical research were defined and the method of obtaining data on machined surfaces directly from machining programs was described. In the following part of the article, the results of the research consisting in determining the probability of machining operations in the working space of a numerically controlled milling machine were presented on the example of machining programs designed for implementation on the DMC 1035V Ecolinc vertical machining centre. The knowledge of the load distribution in the working space of a milling machine associated with the machining process can be used to design and manufacture the test pieces reflecting the machining tasks performed on the milling machine and to develop appropriate acceptance and evaluation procedures.
- 1 January 2021
- Published by Wydawnictwo Naukowe Gabriel Borowski (WNGB) in Advances in Science and Technology Research Journal
- Vol. 15 (1) , 283-289
Open AccessStatistical Testing of Milled Objects on Numerically Controlled Three-Axis Milling Machines
Statistical studies of the surface distribution of milled workpieces and the possibility of their use for operation-based tests and machine tool evaluation were presented. In the first part of the paper, the assumptions and scope of statistical research were defined and the method of obtaining data on machined surfaces directly from machining programs was described. In the following part of the article, the results of the research consisting in determining the probability of machining operations in the working space of a numerically controlled milling machine were presented on the example of machining programs designed for implementation on the DMC 1035V Ecolinc vertical machining centre. The knowledge of the load distribution in the working space of a milling machine associated with the machining process can be used to design and manufacture the test pieces reflecting the machining tasks performed on the milling machine and to develop appropriate acceptance and evaluation procedures.
- Open Access
- 1 December 2020
- Published by Wydawnictwo Naukowe Gabriel Borowski (WNGB) in Advances in Science and Technology Research Journal
- Vol. 14 (4) , 284-297
Model Research on the Influence of Bearing Preload Change on the Frequency and Form if Natural Vibrations of the Spindle System
The article presents an FEM model of the spindle system, in which angular contact ball bearings with active preload control are used. This model allowed to determine the frequency and form of natural vibrations of the system. The model was prepared using the Abaqus programming environment....
- 1 December 2020
- Published by Wydawnictwo Naukowe Gabriel Borowski (WNGB) in Advances in Science and Technology Research Journal
- Vol. 14 (4) , 284-297
Open AccessModel Research on the Influence of Bearing Preload Change on the Frequency and Form if Natural Vibrations of the Spindle System
The article presents an FEM model of the spindle system, in which angular contact ball bearings with active preload control are used. This model allowed to determine the frequency and form of natural vibrations of the system. The model was prepared using the Abaqus programming environment....
- 3 November 2020
- Published by Wroclaw Board of Scientific Technical Societies Federation NOT in Journal of Machine Engineering
- Vol. 20 (4) , 139-151
ANALYSIS OF GLASS GATHERER ROBOT'S VIBRATION DAMPING USING THE ORIGINAL AND MODIFIED DESIGN OF THE FRICTION DAMPER
This paper presents the results of tests carried out on the glass robot’s lance equipped with a prototype friction damper. Two ways of mounting the damper (the original design and the modified design) are described. A series of experimental tests were carried out for each of the ways of...
- 3 November 2020
- Published by Wroclaw Board of Scientific Technical Societies Federation NOT in Journal of Machine Engineering
- Vol. 20 (4) , 139-151
ANALYSIS OF GLASS GATHERER ROBOT'S VIBRATION DAMPING USING THE ORIGINAL AND MODIFIED DESIGN OF THE FRICTION DAMPER
This paper presents the results of tests carried out on the glass robot’s lance equipped with a prototype friction damper. Two ways of mounting the damper (the original design and the modified design) are described. A series of experimental tests were carried out for each of the ways of...
- Open Access
- 1 September 2020
- Published by Wydawnictwo Naukowe Gabriel Borowski (WNGB) in Advances in Science and Technology Research Journal
- Vol. 14 (3) , 158-164
Study on the Impact of Cutting Tool Wear on Machine Tool Energy Consumption
The paper describes the problem of tool wear in machining processes. The importance of determining and analysing the demand of machining centres for electricity was emphasised and the potential relationship between tool wear and machine energy consumption was indicated. The paper presents the...
- 1 September 2020
- Published by Wydawnictwo Naukowe Gabriel Borowski (WNGB) in Advances in Science and Technology Research Journal
- Vol. 14 (3) , 158-164
Open AccessStudy on the Impact of Cutting Tool Wear on Machine Tool Energy Consumption
The paper describes the problem of tool wear in machining processes. The importance of determining and analysing the demand of machining centres for electricity was emphasised and the potential relationship between tool wear and machine energy consumption was indicated. The paper presents the...
- Open Access
- 1 November 2019
- Published by SIMP Redakcja Mechanik - Agenda Wydawnicza SIMP in Mechanik
- No. 11,p. 698-700
Controlling the preload adjustment system of bearings in the machine spindle model using the LabVIEW environment
- 1 November 2019
- Published by SIMP Redakcja Mechanik - Agenda Wydawnicza SIMP in Mechanik
- No. 11,p. 698-700
Open AccessControlling the preload adjustment system of bearings in the machine spindle model using the LabVIEW environment
- Open Access
- 1 October 2019
- Published by SIMP Redakcja Mechanik - Agenda Wydawnicza SIMP in Mechanik
- No. 10,p. 620-622
Assessment of cutting machine energy consumption on the example of the VF-7/50 vertical milling center
- 1 October 2019
- Published by SIMP Redakcja Mechanik - Agenda Wydawnicza SIMP in Mechanik
- No. 10,p. 620-622
Open AccessAssessment of cutting machine energy consumption on the example of the VF-7/50 vertical milling center
- Open Access
- 1 December 2018
- Published by SIMP Redakcja Mechanik - Agenda Wydawnicza SIMP in Mechanik
- No. 12,p. 1116-1119
Possibility of temperature control on the test point study of elastomer properties
- 1 December 2018
- Published by SIMP Redakcja Mechanik - Agenda Wydawnicza SIMP in Mechanik
- No. 12,p. 1116-1119
Open AccessPossibility of temperature control on the test point study of elastomer properties