Marek Stembalski
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Marek Stembalski has a total of 16 co-authors. Here are the top co-authors by number of shared publications:
- Tomasz Szydłowski
Department of Vehicles and Fundamentals of Machine Design, Lodz University of Technology, 90-924 Łódź, Poland
7 shared publications - Arkadiusz Czarnuch
Łódź University of Technology
4 shared publications - Damian Batory
Department of Vehicles and Fundamentals of Machine Design, Lodz University of Technology, 1/15 Stefanowskiego St., 90-924 Lodz, Poland
4 shared publications - Wacław Skoczyński
Faculty of Mechanical Engineering, Wroclaw University of Science and Technology, 50-370 Wroclaw, Poland
4 shared publications - Andrzej Roszkowski
Wroclaw Univ Technol & Sci, Fac Mech Engn, Lukasiewicza 5, PL-50370 Wroclaw, Poland
3 shared publications - Paweł Turek
Department of Machine Tools and Mechanical Engineering Technologies, Faculty of Mechanical Engineering, Wrocław University of Science and Technology, Łukasiewicza 5, 50-371 Wrocław, Poland
2 shared publications
Latest Publications
- Open Access
- 1 June 2026
- Published by WNGB Scientific Publishing House Sp. z o.o. in Advances in Science and Technology Research Journal
- Vol. 20 (6) , 135-148
Validating the durability testing method for large-sized vehicles based on dynamic characteristics of shock absorbers-extended tests
Road simulators are one of the methods of conducting durability tests. The article evaluates the methodology developed by the authors and described in earlier publications for durability tests on road vehicles using the Road Simulator. This evaluation was conducted by comparing the dynamic...
- 1 June 2026
- Published by WNGB Scientific Publishing House Sp. z o.o. in Advances in Science and Technology Research Journal
- Vol. 20 (6) , 135-148
Open AccessValidating the durability testing method for large-sized vehicles based on dynamic characteristics of shock absorbers-extended tests
Road simulators are one of the methods of conducting durability tests. The article evaluates the methodology developed by the authors and described in earlier publications for durability tests on road vehicles using the Road Simulator. This evaluation was conducted by comparing the dynamic...
- Open Access
- 27 November 2025
- Published by MDPI AG in Applied Sciences
- Vol. 15 (23) , 12567
Influence of Shock Absorber Construction on Production Parameters of Its Prototype Solutions
This article describes the conducted examinations of five different prototype shock absorbers. The differences resulted from deliberate modifications to their components. The tests were divided into five series of measurements, each involving testing five identical shock absorber designs. The authors assessed the repeatability and process capability of the production process for each shock absorber design. The study also aimed to identify factors that could lead to undesirable variations in the shock absorber’s dynamic parameters, such as damping force, the shape of the force–displacement characteristic, differences in the system’s response during compression and rebound, and the variability of the response depending on the piston’s speed. The results were then analyzed by using various research methods, among which the most important is the SPC (Statistical Process Control) method. Furthermore, statistical results, such as Cp, Cpk, stability graphs, and process repeatability, are presented.
- 27 November 2025
- Published by MDPI AG in Applied Sciences
- Vol. 15 (23) , 12567
Open AccessInfluence of Shock Absorber Construction on Production Parameters of Its Prototype Solutions
This article describes the conducted examinations of five different prototype shock absorbers. The differences resulted from deliberate modifications to their components. The tests were divided into five series of measurements, each involving testing five identical shock absorber designs. The authors assessed the repeatability and process capability of the production process for each shock absorber design. The study also aimed to identify factors that could lead to undesirable variations in the shock absorber’s dynamic parameters, such as damping force, the shape of the force–displacement characteristic, differences in the system’s response during compression and rebound, and the variability of the response depending on the piston’s speed. The results were then analyzed by using various research methods, among which the most important is the SPC (Statistical Process Control) method. Furthermore, statistical results, such as Cp, Cpk, stability graphs, and process repeatability, are presented.
- 9 June 2025
- Published by Wroclaw Board of Scientific Technical Societies Federation NOT in Journal of Machine Engineering
- Vol. 25 (2) , 43-63
Gear Wear Mechanisms, Monitoring Techniques and Their Potential Use in Gear Predictive Maintenance
In order to ensure the undisturbed operation of gear transmissions, avoid their unplanned downtimes and secondary damage to them, their condition needs to be monitored and their failures need to be diagnosed. Currently, there is no commercial and universal diagnostic system for predictive analysis of gear wear. There are also no limit values of wear indicators defining individual causes of wear. The article presents problems related to various mechanisms of gear wear. Different methods of monitoring the condition of the gear are presented. They are presented. Thermal methods, analysis of wear residues, and measurements and analysis of vibrations and acoustic emissions are described. The usefulness of these techniques for predictive maintenance of gear movement is indicated. It is proposed to extend gear diagnostics by using machine learning methods to detect their faults, and in particular critical states of gear wear.
- 9 June 2025
- Published by Wroclaw Board of Scientific Technical Societies Federation NOT in Journal of Machine Engineering
- Vol. 25 (2) , 43-63
Gear Wear Mechanisms, Monitoring Techniques and Their Potential Use in Gear Predictive Maintenance
In order to ensure the undisturbed operation of gear transmissions, avoid their unplanned downtimes and secondary damage to them, their condition needs to be monitored and their failures need to be diagnosed. Currently, there is no commercial and universal diagnostic system for predictive analysis of gear wear. There are also no limit values of wear indicators defining individual causes of wear. The article presents problems related to various mechanisms of gear wear. Different methods of monitoring the condition of the gear are presented. They are presented. Thermal methods, analysis of wear residues, and measurements and analysis of vibrations and acoustic emissions are described. The usefulness of these techniques for predictive maintenance of gear movement is indicated. It is proposed to extend gear diagnostics by using machine learning methods to detect their faults, and in particular critical states of gear wear.
- 7 October 2024
- Published by Wroclaw Board of Scientific Technical Societies Federation NOT in Journal of Machine Engineering
- Vol. 24 (3) , 119-132
Influence of Shock Absorber on Electric Axle Vibration in Semi-Trailer
This article describes the results of a study of the effect of a shock absorber on the vibration of an electric axle in a semi-trailer. The dynamic characteristics of three shock absorbers from different manufacturers were determined. They were then installed on the electric axle of a semi-trailer equipped with a measuring apparatus. Test runs were carried out on two types of road surface - a test track with a defined profile and a local road. Each run was repeated for a fully loaded and an empty semi-trailer. These tests were designed to determine the values of the dynamic parameters of the electric axle during operation of the semi-trailer depending on the shock absorber used.
- 7 October 2024
- Published by Wroclaw Board of Scientific Technical Societies Federation NOT in Journal of Machine Engineering
- Vol. 24 (3) , 119-132
Influence of Shock Absorber on Electric Axle Vibration in Semi-Trailer
This article describes the results of a study of the effect of a shock absorber on the vibration of an electric axle in a semi-trailer. The dynamic characteristics of three shock absorbers from different manufacturers were determined. They were then installed on the electric axle of a semi-trailer equipped with a measuring apparatus. Test runs were carried out on two types of road surface - a test track with a defined profile and a local road. Each run was repeated for a fully loaded and an empty semi-trailer. These tests were designed to determine the values of the dynamic parameters of the electric axle during operation of the semi-trailer depending on the shock absorber used.
- Open Access
- 22 December 2023
- Published by MDPI AG in Applied Sciences
- Vol. 14 (1) , 127
Assessment of the Possibility of Validating the Durability Testing Method for Large-Sized Vehicles Based on Changes in Shock Absorber Characteristics—Preliminary Tests
The use of road simulators in vehicle durability tests enables a significant reduction in time related to the implementation of a new product. However, there is still a need to improve the methods of these tests in order to obtain a full correlation between the time of the tests on the simulator with respect to the mileage of the vehicle in real road conditions. The aim of this work is a validation and improvement of the durability testing method for large-sized vehicles. Comparative tests of shock absorbers dismantled from semi-trailers with different mileage and shock absorbers dismantled from semi-trailers after durability tests conducted at the MTS test bench are presented. The relationship between the maximum damping force and the displacement speed of the shock absorber piston was examined. Additionally, the influence of the shock absorber temperature on the damping force was analyzed. As a result of the tests, the dynamic characteristics of the shock absorbers were determined and the relationship between the maximum damping force and the mileage of the trailers was determined. It was found that the load on the trailers during their operation has a significant impact on the change in the characteristics of the shock absorbers. What is new in this publication is the validation of the methodology for conducting durability tests previously proposed by the authors based on the selected component, which is the shock absorber. The authors have not yet encountered in the literature any attempt to validate the methodology for conducting durability tests for large-sized vehicles.
- 22 December 2023
- Published by MDPI AG in Applied Sciences
- Vol. 14 (1) , 127
Open AccessAssessment of the Possibility of Validating the Durability Testing Method for Large-Sized Vehicles Based on Changes in Shock Absorber Characteristics—Preliminary Tests
The use of road simulators in vehicle durability tests enables a significant reduction in time related to the implementation of a new product. However, there is still a need to improve the methods of these tests in order to obtain a full correlation between the time of the tests on the simulator with respect to the mileage of the vehicle in real road conditions. The aim of this work is a validation and improvement of the durability testing method for large-sized vehicles. Comparative tests of shock absorbers dismantled from semi-trailers with different mileage and shock absorbers dismantled from semi-trailers after durability tests conducted at the MTS test bench are presented. The relationship between the maximum damping force and the displacement speed of the shock absorber piston was examined. Additionally, the influence of the shock absorber temperature on the damping force was analyzed. As a result of the tests, the dynamic characteristics of the shock absorbers were determined and the relationship between the maximum damping force and the mileage of the trailers was determined. It was found that the load on the trailers during their operation has a significant impact on the change in the characteristics of the shock absorbers. What is new in this publication is the validation of the methodology for conducting durability tests previously proposed by the authors based on the selected component, which is the shock absorber. The authors have not yet encountered in the literature any attempt to validate the methodology for conducting durability tests for large-sized vehicles.
- Open Access
Analysis of the Correctness of Mapping the Passage of a Semi-Trailer through a Road Obstacle on a Road Simulator
Road simulators enable accelerated durability tests under similar-to-real road conditions. However, the road simulator itself generates the signals with the appropriate strength and amplitude that is adequate to the response registered by the sensors during the real run. Therefore, there is a need for verification of the validity of the representation of vehicle runs on a road simulator in terms of the shape of the generated profile and possible sources of uncertainty. The tests in this study were carried out for a multi-axle vehicle passing an obstacle of known shape. Various signals were registered while the vehicle was passing over the obstacle. The MTS (System Corporation) road simulator’s response to the signal given by the obstacle was then checked. The results showed a 99% correlation between the simulation and the road test results. A numerical model of the vehicle was developed to verify the quality of representation of the real conditions by the road simulator, especially in terms of forces resulting from the road profile. Interestingly, the input signal generated by the road simulator provided a very good accuracy of the vehicle response, as tested with use of the numerical model.
Open AccessAnalysis of the Correctness of Mapping the Passage of a Semi-Trailer through a Road Obstacle on a Road Simulator
Road simulators enable accelerated durability tests under similar-to-real road conditions. However, the road simulator itself generates the signals with the appropriate strength and amplitude that is adequate to the response registered by the sensors during the real run. Therefore, there is a need for verification of the validity of the representation of vehicle runs on a road simulator in terms of the shape of the generated profile and possible sources of uncertainty. The tests in this study were carried out for a multi-axle vehicle passing an obstacle of known shape. Various signals were registered while the vehicle was passing over the obstacle. The MTS (System Corporation) road simulator’s response to the signal given by the obstacle was then checked. The results showed a 99% correlation between the simulation and the road test results. A numerical model of the vehicle was developed to verify the quality of representation of the real conditions by the road simulator, especially in terms of forces resulting from the road profile. Interestingly, the input signal generated by the road simulator provided a very good accuracy of the vehicle response, as tested with use of the numerical model.
- 22 February 2023
- Published by Springer Nature
- p. 236-246
Methodology of the Durability Tests of Semi-trailers on the MTS 320 Road Simulator
- 22 February 2023
- Published by Springer Nature
- p. 236-246
Methodology of the Durability Tests of Semi-trailers on the MTS 320 Road Simulator
- 15 August 2022
- Published by University of Slavonski Brod in Tehnicki vjesnik - Technical Gazette
- Vol. 29 (4) , 1433-1438
Strength Analysis of an Electric Scooter Frame During Simulation of an Obstacle Collision at 45 Degrees
This paper describes the simulation of a 45° angle collision of a modelled electric scooter frame including suspension with a non-deformable wall using the finite element method. Includes creation of a CAD geometric model using the surface method wit...
- 15 August 2022
- Published by University of Slavonski Brod in Tehnicki vjesnik - Technical Gazette
- Vol. 29 (4) , 1433-1438
Strength Analysis of an Electric Scooter Frame During Simulation of an Obstacle Collision at 45 Degrees
This paper describes the simulation of a 45° angle collision of a modelled electric scooter frame including suspension with a non-deformable wall using the finite element method. Includes creation of a CAD geometric model using the surface method wit...
- 3 November 2020
- Published by Wroclaw Board of Scientific Technical Societies Federation NOT in Journal of Machine Engineering
- Vol. 20 (4) , 139-151
ANALYSIS OF GLASS GATHERER ROBOT'S VIBRATION DAMPING USING THE ORIGINAL AND MODIFIED DESIGN OF THE FRICTION DAMPER
This paper presents the results of tests carried out on the glass robot’s lance equipped with a prototype friction damper. Two ways of mounting the damper (the original design and the modified design) are described. A series of experimental tests were carried out for each of the ways of...
- 3 November 2020
- Published by Wroclaw Board of Scientific Technical Societies Federation NOT in Journal of Machine Engineering
- Vol. 20 (4) , 139-151
ANALYSIS OF GLASS GATHERER ROBOT'S VIBRATION DAMPING USING THE ORIGINAL AND MODIFIED DESIGN OF THE FRICTION DAMPER
This paper presents the results of tests carried out on the glass robot’s lance equipped with a prototype friction damper. Two ways of mounting the damper (the original design and the modified design) are described. A series of experimental tests were carried out for each of the ways of...