Jan Godzimirski
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Jan Godzimirski has a total of 36 co-authors. Here are the top co-authors by number of shared publications:
- Andrzej Komorek
Department of Aviation, Polish Air Force University, 08-530 Deblin, Poland
15 shared publications - Marek Rośkowicz
Faculty of Mechatronics, Armament and Aerospace, Military University of Technology, 00-908 Warsaw, Poland
14 shared publications - Iga Barca
Faculty of Mechatronics, Armament and Aerospace, Military University of Technology, 00-908 Warsaw, Poland
3 shared publications - Michał Jasztal
Faculty of Mechatronics, Armament and Aerospace, Military University of Technology, 00-908 Warsaw, Poland
3 shared publications Agata Pietras
Wydział Mechatroniki, Wojskowa Akademia Techniczna, ul. S. Kaliskiego 2, 00-908 Warszawa, Poland
2 shared publications- Angelika Arkuszyńska
Faculty of Mechatronics, Armament and Aerospace, Military University of Technology, 00-908 Warszawa, Poland
2 shared publications
Latest Publications
- Open Access
Impact Strength of Adhesive Joints of Pre-Impregnated Composite Elements
Composite materials’ contribution to the construction of manned and unmanned aircraft continues to grow and, together with the increased use of these materials, there is a growing need to develop an optimal method of joining composite components and carrying out repairs following operational damage. One such method is bonding by means of adhesive bonds, many of whose properties are already quite well known. However, relatively little is known about the impact strength of adhesive joints in general, including adhesive joints of composite components. This paper presents a concept for conducting such tests using adhesive lap joints. The sample pieces were cut from a 9-layer, 2 mm thick composite panel made with an autoclave technique. The results show that the lowest impact strength and shear strength occurred for adhesive joints made with an epoxy adhesive with the highest Young’s modulus. The best results were obtained for the adhesive whose joints became destroyed in equal proportions in a cohesive–adhesive manner.
Open AccessImpact Strength of Adhesive Joints of Pre-Impregnated Composite Elements
Composite materials’ contribution to the construction of manned and unmanned aircraft continues to grow and, together with the increased use of these materials, there is a growing need to develop an optimal method of joining composite components and carrying out repairs following operational damage. One such method is bonding by means of adhesive bonds, many of whose properties are already quite well known. However, relatively little is known about the impact strength of adhesive joints in general, including adhesive joints of composite components. This paper presents a concept for conducting such tests using adhesive lap joints. The sample pieces were cut from a 9-layer, 2 mm thick composite panel made with an autoclave technique. The results show that the lowest impact strength and shear strength occurred for adhesive joints made with an epoxy adhesive with the highest Young’s modulus. The best results were obtained for the adhesive whose joints became destroyed in equal proportions in a cohesive–adhesive manner.
- 30 June 2024
- Published by Rzeszow University of Technology in Technologia i Automatyzacja Montażu
- Vol. 124 (2) , 3-10
Influence of the temperature changes on stresses in carbon composite fastening bolts
High joint strength of composite structures can be achieved by using mechanical fasteners. The materials used for rivets and bolts have lower coefficients of thermal expansion than composites in the direction perpendicular to the reinforcement fibers. It is suspected, therefore, that temperature changes can cause stress changes in mechanical fasteners. The purpose of this study was to experimentally determine and analytically substantiate the values of stress changes resulting from a change in temperature in the range from -20 to 60°C in M8 steel bolts fastening carbon composite. The value of stress changes was estimated to be around 100 MPa, which can consequently lead to joint unsealing or plastic deformation of the mechanical fastener.
- 30 June 2024
- Published by Rzeszow University of Technology in Technologia i Automatyzacja Montażu
- Vol. 124 (2) , 3-10
Influence of the temperature changes on stresses in carbon composite fastening bolts
High joint strength of composite structures can be achieved by using mechanical fasteners. The materials used for rivets and bolts have lower coefficients of thermal expansion than composites in the direction perpendicular to the reinforcement fibers. It is suspected, therefore, that temperature changes can cause stress changes in mechanical fasteners. The purpose of this study was to experimentally determine and analytically substantiate the values of stress changes resulting from a change in temperature in the range from -20 to 60°C in M8 steel bolts fastening carbon composite. The value of stress changes was estimated to be around 100 MPa, which can consequently lead to joint unsealing or plastic deformation of the mechanical fastener.
- Open Access
- 1 January 2024
- Published by Rzeszow University of Technology in Technologia i Automatyzacja Montażu
- Vol. 126 (4) , 3-13
Strength tests of repair joints loaded with tension and loss of stability
During aircraft service, the skin is the component that first comes into contact with factors that can cause mechanical damage - that is why it is most often damaged during use. Semi-monocoque aircraft structures are made of a skin (usually aluminum alloy) and a frame. The skin is an element that significantly affects the safety of the structure, since it transfers loads between the elements of the frame. For this reason, the skin is subject to special supervision during technical maintenance, and any damage detected must be repaired. The research was carried out on specimens made of AW 2024-T3 plate sheet with a thickness of 1 mm. In the study, a comparative analysis of damaged, undamaged and repaired specimens loaded in tension and compression was performed. Different patches were used in repaired specimens, made of metallic as well as composite materials, connected to the structure with rivets or using adhesive materials. The study showed that the use of riveted as well as adhesively bonded overlays does not allow the original strength of the tensile-loaded skin to be restored, but does allow the strength of the compression-loaded skin to be restored (loss of stability). In addition, numerical simulations were performed to define the stress field occurring in the adhesive joint for different geometric dimensions of the plate (thickness, width). The results of the numerical analysis showed that the geometry of the plate model influences the values of reduced stresses in the adhesive weld and the patch. Regardless of the analyzed changes in the geometry of the plate model, the maximum values of reduced stresses are similar to each other. The smallest values of reduced stresses in the adhesive joint and composite patch were obtained for the case of a plate with a thickness of 1 mm and a width of 160 mm.
- 1 January 2024
- Published by Rzeszow University of Technology in Technologia i Automatyzacja Montażu
- Vol. 126 (4) , 3-13
Open AccessStrength tests of repair joints loaded with tension and loss of stability
During aircraft service, the skin is the component that first comes into contact with factors that can cause mechanical damage - that is why it is most often damaged during use. Semi-monocoque aircraft structures are made of a skin (usually aluminum alloy) and a frame. The skin is an element that significantly affects the safety of the structure, since it transfers loads between the elements of the frame. For this reason, the skin is subject to special supervision during technical maintenance, and any damage detected must be repaired. The research was carried out on specimens made of AW 2024-T3 plate sheet with a thickness of 1 mm. In the study, a comparative analysis of damaged, undamaged and repaired specimens loaded in tension and compression was performed. Different patches were used in repaired specimens, made of metallic as well as composite materials, connected to the structure with rivets or using adhesive materials. The study showed that the use of riveted as well as adhesively bonded overlays does not allow the original strength of the tensile-loaded skin to be restored, but does allow the strength of the compression-loaded skin to be restored (loss of stability). In addition, numerical simulations were performed to define the stress field occurring in the adhesive joint for different geometric dimensions of the plate (thickness, width). The results of the numerical analysis showed that the geometry of the plate model influences the values of reduced stresses in the adhesive weld and the patch. Regardless of the analyzed changes in the geometry of the plate model, the maximum values of reduced stresses are similar to each other. The smallest values of reduced stresses in the adhesive joint and composite patch were obtained for the case of a plate with a thickness of 1 mm and a width of 160 mm.
- Open Access
- 1 January 2024
- Published by Rzeszow University of Technology in Technologia i Automatyzacja Montażu
- Vol. 125 (3) , 3-11
A proposal for a new method of testing the impact strength of adhesive joints
The usefulness of the proprietary method of testing the impact strength of adhesive joints under shear loads was checked. An adhesively bonded lap sample of flat bars with a thickness of 5 mm, loaded on the side surface of the overlap, was proposed. Numerical calculations have shown that in such a loaded lap joint, shear stresses dominate. Impact tests of such specimens can be performed on conventional Charpy hammers. The conducted experimental tests showed high reproducibility of the results of such tests and as expected, higher destruction energy of flexible adhesive and adhesive layers of greater thickness was obtained.
- 1 January 2024
- Published by Rzeszow University of Technology in Technologia i Automatyzacja Montażu
- Vol. 125 (3) , 3-11
Open AccessA proposal for a new method of testing the impact strength of adhesive joints
The usefulness of the proprietary method of testing the impact strength of adhesive joints under shear loads was checked. An adhesively bonded lap sample of flat bars with a thickness of 5 mm, loaded on the side surface of the overlap, was proposed. Numerical calculations have shown that in such a loaded lap joint, shear stresses dominate. Impact tests of such specimens can be performed on conventional Charpy hammers. The conducted experimental tests showed high reproducibility of the results of such tests and as expected, higher destruction energy of flexible adhesive and adhesive layers of greater thickness was obtained.
- Open Access
Static and Fatigue Strength and Failure Mechanisms of Riveted Lap Joints of CFRP Composites
The background of this work is the search for the most effective ways of joining composites, inter alia in aeronautical applications. The purpose of this study was to analyze the impact of mechanical fastener types on the static strength of lap joints of composite elements and the impact of fasteners on the mechanism of failure of such joints under fatigue load. The second objective was to check to what extent the hybridization of such joints, consisting of supplementing them with an adhesive joint, affects their strength and the mechanism of failure of such joints loaded with fatigue. Damage to composite joints was observed using computed tomography technology. The fasteners used in this study (aluminum rivets, Hi-lok and Jo-Bolt) differed not only in terms of the materials they were made of, but also in terms of the pressure forces they exerted on the joined parts. Finally, in order to check how a partially cracked adhesive joint affects the load on the fasteners, numerical calculations were carried out. Analyzing the results of the research, it was found that partial damage to the adhesive joint of the hybrid joint does not increase the load on the rivets and does not impair the fatigue life of the joint. An important advantage of hybrid joint is the two-stage destruction of the connection, which significantly increases the safety of aircraft structures and facilitates the process of supervising their technical condition.
Open AccessStatic and Fatigue Strength and Failure Mechanisms of Riveted Lap Joints of CFRP Composites
The background of this work is the search for the most effective ways of joining composites, inter alia in aeronautical applications. The purpose of this study was to analyze the impact of mechanical fastener types on the static strength of lap joints of composite elements and the impact of fasteners on the mechanism of failure of such joints under fatigue load. The second objective was to check to what extent the hybridization of such joints, consisting of supplementing them with an adhesive joint, affects their strength and the mechanism of failure of such joints loaded with fatigue. Damage to composite joints was observed using computed tomography technology. The fasteners used in this study (aluminum rivets, Hi-lok and Jo-Bolt) differed not only in terms of the materials they were made of, but also in terms of the pressure forces they exerted on the joined parts. Finally, in order to check how a partially cracked adhesive joint affects the load on the fasteners, numerical calculations were carried out. Analyzing the results of the research, it was found that partial damage to the adhesive joint of the hybrid joint does not increase the load on the rivets and does not impair the fatigue life of the joint. An important advantage of hybrid joint is the two-stage destruction of the connection, which significantly increases the safety of aircraft structures and facilitates the process of supervising their technical condition.
- Open Access
Temperature Rise of an Adhesive Particle-Reinforced Polymer during Fatigue Testing
Construction adhesives are usually polymers that have been modified to achieve specific properties so that they can be used under various loading conditions. An attempt was made to estimate the effect of fatigue loading on the temperature of an adhesive material by further physically modifying the basic adhesive composition used in the research. The temperature of the materials during the tests was recorded using a thermal imaging camera and a thermoelectric thermometer. For most materials tested at 20 Hz, an increase in the number of load cycles corresponded to an increase in the temperature of the samples. For a frequency of 30 Hz, after the temperature increased by a certain value, the temperature of the modified samples recorded with the thermal imaging camera decreased. Fatigue loading caused an increase of the temperature of all tested polymeric materials. Observation of the sample during testing with a thermal imaging camera allows a simple identification of the areas with the highest temperature and can be much more useful in practice than recording temperatures with a thermocouple thermometer, as thermocouples need to be properly positioned before testing.
Open AccessTemperature Rise of an Adhesive Particle-Reinforced Polymer during Fatigue Testing
Construction adhesives are usually polymers that have been modified to achieve specific properties so that they can be used under various loading conditions. An attempt was made to estimate the effect of fatigue loading on the temperature of an adhesive material by further physically modifying the basic adhesive composition used in the research. The temperature of the materials during the tests was recorded using a thermal imaging camera and a thermoelectric thermometer. For most materials tested at 20 Hz, an increase in the number of load cycles corresponded to an increase in the temperature of the samples. For a frequency of 30 Hz, after the temperature increased by a certain value, the temperature of the modified samples recorded with the thermal imaging camera decreased. Fatigue loading caused an increase of the temperature of all tested polymeric materials. Observation of the sample during testing with a thermal imaging camera allows a simple identification of the areas with the highest temperature and can be much more useful in practice than recording temperatures with a thermocouple thermometer, as thermocouples need to be properly positioned before testing.
- 1 January 2023
- Published by Rzeszow University of Technology in Technologia i Automatyzacja Montażu
- Vol. 122 (4) , 20-27
The influence of adhesive material properties on the impact strength of adhesive block connections
Adhesive connections are becoming increasingly popular in the construction of aircraft and other means of transport. Today, bonding is mainly used in the construction of helicopter fuselages, wings or lifting rotors. The increased popularity of bonding is forcing designers to seek new and improve research methods as well as enhancing the existing test methods which specify the static, fatigue or impact strength of joints. A variety of tests are used to determine the strength of structures, although new ones are constantly being sought so as to be applied more quickly and without specialised equipment. Current testing standards are also being modified in order to speed up and simplify the testing process, resulting in safer structures that use adhesive bonds. The aim of the research presented in this paper was to test whether there is a relationship between the mechanical properties of adhesive materials and the impact strength of adhesive block joints with a cylindrical top element. Steels S235, Raex 400 and PA6 aluminium alloy were used for the manufacture of the samples. From each material, 10 samples were prepared with upper elements of different diameters, namely: 17.8 mm, 12.6 mm and 8.9 mm. A pendulum hammer was used to determine the strength of the adhesive bond against dynamic load application. For the sake of the research, the authors used a modified PN-EN ISO 9653 with a mounted hammer equal to the maximum energy of 15 J. Lower failure energy was characteristic of samples made from material with a lower value of Young's modulus (dural) and from steel with a lower yield strength. The connection failure energy grew with increasing the joint area, which was approximately parabolic.
- 1 January 2023
- Published by Rzeszow University of Technology in Technologia i Automatyzacja Montażu
- Vol. 122 (4) , 20-27
The influence of adhesive material properties on the impact strength of adhesive block connections
Adhesive connections are becoming increasingly popular in the construction of aircraft and other means of transport. Today, bonding is mainly used in the construction of helicopter fuselages, wings or lifting rotors. The increased popularity of bonding is forcing designers to seek new and improve research methods as well as enhancing the existing test methods which specify the static, fatigue or impact strength of joints. A variety of tests are used to determine the strength of structures, although new ones are constantly being sought so as to be applied more quickly and without specialised equipment. Current testing standards are also being modified in order to speed up and simplify the testing process, resulting in safer structures that use adhesive bonds. The aim of the research presented in this paper was to test whether there is a relationship between the mechanical properties of adhesive materials and the impact strength of adhesive block joints with a cylindrical top element. Steels S235, Raex 400 and PA6 aluminium alloy were used for the manufacture of the samples. From each material, 10 samples were prepared with upper elements of different diameters, namely: 17.8 mm, 12.6 mm and 8.9 mm. A pendulum hammer was used to determine the strength of the adhesive bond against dynamic load application. For the sake of the research, the authors used a modified PN-EN ISO 9653 with a mounted hammer equal to the maximum energy of 15 J. Lower failure energy was characteristic of samples made from material with a lower value of Young's modulus (dural) and from steel with a lower yield strength. The connection failure energy grew with increasing the joint area, which was approximately parabolic.
- Open Access
- 1 January 2023
- Published by Rzeszow University of Technology in Technologia i Automatyzacja Montażu
- Vol. 121 (3) , 3-12
Analysis of the properties of orthotropic composites in terms of their use in airframe repairs
The aim of the research was to determine the basic strength properties of orthotropic composites in terms of their use in the repair of aircraft airframes. The objects of the tests were three types of composites reinforced with carbon fibers: produced using the wet method with a thickness of 2.5 mm, commercial with a thickness of 2 mm and commercial with a thickness of 7.3 mm. Specimens cut out from the first two types of materials were subjected to a static tensile test with a force applied in the direction of the fibers and at an angle of 45°, which enabled the determination of tensile strength and modulus of elasticity. Specimens made of 7.3 mm thick composite were subjected to four-point bending and tensile tests to determine Young's modulus, compression and impact strength, also taking into account two directions of load application. The values of stresses and Young's modulus determined in this way indicate much lower strength and stiffness of orthotropic composites apart from the reinforcement fibers’ directions, which is the basis for replacing them with quasi-isotropic composites in repairs of aircraft airframes.
- 1 January 2023
- Published by Rzeszow University of Technology in Technologia i Automatyzacja Montażu
- Vol. 121 (3) , 3-12
Open AccessAnalysis of the properties of orthotropic composites in terms of their use in airframe repairs
The aim of the research was to determine the basic strength properties of orthotropic composites in terms of their use in the repair of aircraft airframes. The objects of the tests were three types of composites reinforced with carbon fibers: produced using the wet method with a thickness of 2.5 mm, commercial with a thickness of 2 mm and commercial with a thickness of 7.3 mm. Specimens cut out from the first two types of materials were subjected to a static tensile test with a force applied in the direction of the fibers and at an angle of 45°, which enabled the determination of tensile strength and modulus of elasticity. Specimens made of 7.3 mm thick composite were subjected to four-point bending and tensile tests to determine Young's modulus, compression and impact strength, also taking into account two directions of load application. The values of stresses and Young's modulus determined in this way indicate much lower strength and stiffness of orthotropic composites apart from the reinforcement fibers’ directions, which is the basis for replacing them with quasi-isotropic composites in repairs of aircraft airframes.
- Open Access
- 1 January 2023
- Published by Rzeszow University of Technology in Technologia i Automatyzacja Montażu
- Vol. 120 (2) , 19-32
Selection of materials for repairing punctures of metal skin of semi-monocoque structures using composite patches
For repairing punctures of skin of semi-monocoque structures under field conditions, simple methods are sought to guarantee the reliability of the repaired structure. Therefore, adhesive joints and composite materials are being increasingly used in repairs. During repairs using adhesion, an important aspect that affects the quality of the joint is the selection of the adhesive and the quality of surface preparation of the parts to be joined. This is necessary to get the right bond strength and durability of the joint in working environments characterized by extreme temperatures and exposure to chemicals and moisture. The purpose of the study was to select an adhesive with good strength properties for bonding AW2024T3 aluminum sheets to carbon and glass composites, and to analyze the effect of metal surface preparation on the strength of adhesive joints (grinding, sandblasting and chemical surface preparation). The tests were carried out on overlap (metal-composite) specimens. For selected adhesives, strength tests were also carried out on specimens replicating the repaired damage with a diameter of 20 mm of metal skin repaired by different methods, including composite patches and adhesive joints. The specimens were loaded in tension and loss of stability. The tests made it possible to determine the requirements for composite patches used for repairing upper and lower airframe wing skins.
- 1 January 2023
- Published by Rzeszow University of Technology in Technologia i Automatyzacja Montażu
- Vol. 120 (2) , 19-32
Open AccessSelection of materials for repairing punctures of metal skin of semi-monocoque structures using composite patches
For repairing punctures of skin of semi-monocoque structures under field conditions, simple methods are sought to guarantee the reliability of the repaired structure. Therefore, adhesive joints and composite materials are being increasingly used in repairs. During repairs using adhesion, an important aspect that affects the quality of the joint is the selection of the adhesive and the quality of surface preparation of the parts to be joined. This is necessary to get the right bond strength and durability of the joint in working environments characterized by extreme temperatures and exposure to chemicals and moisture. The purpose of the study was to select an adhesive with good strength properties for bonding AW2024T3 aluminum sheets to carbon and glass composites, and to analyze the effect of metal surface preparation on the strength of adhesive joints (grinding, sandblasting and chemical surface preparation). The tests were carried out on overlap (metal-composite) specimens. For selected adhesives, strength tests were also carried out on specimens replicating the repaired damage with a diameter of 20 mm of metal skin repaired by different methods, including composite patches and adhesive joints. The specimens were loaded in tension and loss of stability. The tests made it possible to determine the requirements for composite patches used for repairing upper and lower airframe wing skins.
- Open Access
The Influence of Low-Energy Impact Loads on the Properties of the Sandwich Composite with a Foam Core
Composite materials are widely used in the construction of means of transport. Due to their low density and high stiffness, sandwich composites generate significant interest. The authors conducted static and dynamic tests in order to determine the effect of density and core thickness on the mechanical properties of a sandwich composite. Particular attention was paid to the impact properties of such composites. Herex and Airex polymer foams of different densities were used as cores, whereas the faces were made up of two layers of fabrics: glass and carbon. The matrix base of the tested materials was made of epoxy resin cured with a dedicated hardener. As a result of the study, a significant influence of the core on the strength parameters of the tested spacer materials was found. The examined polymer foams were found to have different adhesive properties, which affected their residual strength after an impact and the nature of destruction of the studied composites. It was observed that sandwich composites with a thicker core of higher density have higher impact strength and resistance to puncture. In the sandwich composites, low-energy impact loads result in damage only to the layer to which the load has been applied and has a core, so repairing such an element is much easier than in classic layered composites without a core. What is very important is that, in contrast to classic laminates, the bottom cover of the composite is not destroyed at low-impact energy values.
Open AccessThe Influence of Low-Energy Impact Loads on the Properties of the Sandwich Composite with a Foam Core
Composite materials are widely used in the construction of means of transport. Due to their low density and high stiffness, sandwich composites generate significant interest. The authors conducted static and dynamic tests in order to determine the effect of density and core thickness on the mechanical properties of a sandwich composite. Particular attention was paid to the impact properties of such composites. Herex and Airex polymer foams of different densities were used as cores, whereas the faces were made up of two layers of fabrics: glass and carbon. The matrix base of the tested materials was made of epoxy resin cured with a dedicated hardener. As a result of the study, a significant influence of the core on the strength parameters of the tested spacer materials was found. The examined polymer foams were found to have different adhesive properties, which affected their residual strength after an impact and the nature of destruction of the studied composites. It was observed that sandwich composites with a thicker core of higher density have higher impact strength and resistance to puncture. In the sandwich composites, low-energy impact loads result in damage only to the layer to which the load has been applied and has a core, so repairing such an element is much easier than in classic layered composites without a core. What is very important is that, in contrast to classic laminates, the bottom cover of the composite is not destroyed at low-impact energy values.