Alexandra Novakova
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Alexandra Novakova has a total of 7 co-authors. Here are the top co-authors by number of shared publications:
- Milan Brožek
Czech University of Life Sciences Prague, Czech Republic
6 shared publications - Anna Brunerová
Department of Material Science and Manufacturing Technology, Faculty of Engineering, Czech University of Life Sciences Prague, Kamýcká 129, 165 00 Prague, Czech Republic
1 shared publication Czech University of Life Sciences Prague
1 shared publicationHelena Píšová
Department of Material Science and Manufacturing Technology Faculty of Engineering Czech University of Life Sci- ences Prague . Kamýcká 129 165 21 Praha 6 -Suchdol Czech Republic
1 shared publicationM. Kolářová
1 shared publicationOta Niedermeier
AŽD Praha, spol. s r. o., Žirovnická 2, 106 00 Praha 10 – Záběhlice, Czech Republic
1 shared publication
Latest Publications
- Open Access
- 1 September 2018
- Published by Ceska zemedelska univerzita v Praze in Scientia Agriculturae Bohemica
- Vol. 49 (3) , 236-243
Energy Balance of Briquette Production from Various Waste Biomass
Production of briquette bio-fuel is related to several aspects of densification process. The present paper deals with the relation between briquette volume density ρ (kg·m −3 ) and required deformation energy E d (J). Wood, energy crop and cardboard feedstocks were compressed by a laboratory briquetting press of two diameters (40 and 65 mm); in this way six kinds of briquette samples (W 40 , W 65 , E 40 , E 65 , C 40 , C 65 ) were produced. The values of compressing force F (N) and briquette volume density ρ were measured directly during feedstock densification; the deformation energy E d was calculated subsequently. The amount of deformation energy E d consumed within the achievement of specific briquette volume density ρ levels differed in case of all samples, the same as the maximum achieved briquette volume density ρ levels. Best results, i.e. efficiency of briquette production (the highest ρ, the lowest E d ), were achieved by cardboard samples, followed by wood and finally by energy crop samples. An overall evaluation indicated a higher production efficiency of briquette samples 40 mm in diameter and the disadvantage of the production of briquette samples with briquette volume density ρ > 1000 kg·m −3 ; above such level, the amount of consumed deformation energy E d increased disproportionately sharply.
- 1 September 2018
- Published by Ceska zemedelska univerzita v Praze in Scientia Agriculturae Bohemica
- Vol. 49 (3) , 236-243
Open AccessEnergy Balance of Briquette Production from Various Waste Biomass
Production of briquette bio-fuel is related to several aspects of densification process. The present paper deals with the relation between briquette volume density ρ (kg·m −3 ) and required deformation energy E d (J). Wood, energy crop and cardboard feedstocks were compressed by a laboratory briquetting press of two diameters (40 and 65 mm); in this way six kinds of briquette samples (W 40 , W 65 , E 40 , E 65 , C 40 , C 65 ) were produced. The values of compressing force F (N) and briquette volume density ρ were measured directly during feedstock densification; the deformation energy E d was calculated subsequently. The amount of deformation energy E d consumed within the achievement of specific briquette volume density ρ levels differed in case of all samples, the same as the maximum achieved briquette volume density ρ levels. Best results, i.e. efficiency of briquette production (the highest ρ, the lowest E d ), were achieved by cardboard samples, followed by wood and finally by energy crop samples. An overall evaluation indicated a higher production efficiency of briquette samples 40 mm in diameter and the disadvantage of the production of briquette samples with briquette volume density ρ > 1000 kg·m −3 ; above such level, the amount of consumed deformation energy E d increased disproportionately sharply.
- 23 May 2018
- Published by Latvia University of Life Sciences and Technologies
Evaluation of selected parameters in blanking
- 23 May 2018
- Published by Latvia University of Life Sciences and Technologies
Evaluation of selected parameters in blanking
- Open Access
- 1 September 2017
- Published by Jan Evangelista Purkyne University in Usti nad Labem in Manufacturing Technology
- Vol. 17 (4) , 423-427
Bonding of Plywood Using Hot Melt Adhesives
The paper presents the strength tests results of joints made by use of two hot melt adhesives. The tests were carried out according to the modified standard ?SN EN 1465 (66 8510) and ?SN EN 205 (66 8508). For bonding the three-layer plywood of...
- 1 September 2017
- Published by Jan Evangelista Purkyne University in Usti nad Labem in Manufacturing Technology
- Vol. 17 (4) , 423-427
Open AccessBonding of Plywood Using Hot Melt Adhesives
The paper presents the strength tests results of joints made by use of two hot melt adhesives. The tests were carried out according to the modified standard ?SN EN 1465 (66 8510) and ?SN EN 205 (66 8508). For bonding the three-layer plywood of...
- 24 May 2017
- Published by Latvia University of Life Sciences and Technologies
Forming resistance determination of steel
- 24 May 2017
- Published by Latvia University of Life Sciences and Technologies
Forming resistance determination of steel
- Open Access
- 1 May 2017
- Published by Mendel University Press in Acta Universitatis Agriculturae et Silviculturae Mendelianae Brunensis
- Vol. 65 (3) , 807-814
Resistance Spot Welding of Steel Sheets of the Same and Different Thickness
Acta Universitatis Agriculturae et Silviculturae Mendelianae Brunensis, the scientific journal of the Mendel University in Brno, Czech Republic
- 1 May 2017
- Published by Mendel University Press in Acta Universitatis Agriculturae et Silviculturae Mendelianae Brunensis
- Vol. 65 (3) , 807-814
Open AccessResistance Spot Welding of Steel Sheets of the Same and Different Thickness
Acta Universitatis Agriculturae et Silviculturae Mendelianae Brunensis, the scientific journal of the Mendel University in Brno, Czech Republic
- Open Access
- 31 March 2012
- Published by Czech Academy of Agricultural Sciences in Research in Agricultural Engineering
- Vol. 58 (1) , 30-35
Quality evaluation of briquettes made from wood waste
» Articles | Agricultural Journals
- 31 March 2012
- Published by Czech Academy of Agricultural Sciences in Research in Agricultural Engineering
- Vol. 58 (1) , 30-35
Open AccessQuality evaluation of briquettes made from wood waste
» Articles | Agricultural Journals