Ilona Szewczak
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Ilona Szewczak has a total of 7 co-authors. Here are the top co-authors by number of shared publications:
- Patryk Różyło
Department of Machine Design and Mechatronics, Faculty of Mechanical Engineering, Lublin University of Technology, Nadbystrzycka 36, 20-618 Lublin, Poland
10 shared publications - Katarzyna Rzeszut
Poznan University of Technology
9 shared publications - Małgorzata Snela
Faculty of Civil Engineering, Lublin University of Technology, 40 Nadbystrzycka Str., 20-618 Lublin, Poland
7 shared publications - Jakub Paśnik
Department of Machine Design and Mechatronics, Faculty of Mechanical Engineering, Lublin University of Technology, Nadbystrzycka 36, 20-618 Lublin, Poland
1 shared publication - Maciej Adam Dybizbański
Faculty of Civil and Transport Engineering, Poznań University of Technology, 5 Marii Skłodowskiej-Curie Str., 60-965 Poznań, Poland
1 shared publication - Michał Guminiak
Poznan University of Technology, Institute of Structural Analysis, Marii Skłodowskiej-Curie 5, 60-965 Poznan
1 shared publication
Latest Publications
- Open Access
Experimental and Numerical Response of Compressed Equal-Leg Steel Angle Members with Different Anchorage Lengths
Reliable tests of compressed steel members require appropriate representation of boundary conditions. This study examined the global response of compressed hot-rolled equal-leg steel angle members with three end-fixture configurations. Nine L50 × 50 × 4 specimens were tested with anchorage lengths of 50, 100, and 150 mm. Because increasing anchorage length reduced the unsupported member length, the observed differences reflect the combined effect of both parameters. Displacements and longitudinal strains were measured using Digital Image Correlation and strain gauges, respectively, and the tests were supplemented by finite element analyses. The configurations produced differences in maximum load and global displacement, although maximum load varied non-monotonically with anchorage length. At the investigated load levels, local longitudinal strains were similar, whereas global displacements differed. The K-5 specimens deformed in the direction opposite to the K-10 and K-15 specimens. Baseline numerical analyses reproduced the observed directions for K-10 and K-15, but not K-5. Reversing the sign of the initial imperfection reproduced the K-5 direction, supporting an interpretation involving two branches of the same global buckling mode; however, the cause of branch selection remained unresolved. The results show that end-fixture configuration should be considered when interpreting experimental and numerical assessments of compressed steel angle members.
Open AccessExperimental and Numerical Response of Compressed Equal-Leg Steel Angle Members with Different Anchorage Lengths
Reliable tests of compressed steel members require appropriate representation of boundary conditions. This study examined the global response of compressed hot-rolled equal-leg steel angle members with three end-fixture configurations. Nine L50 × 50 × 4 specimens were tested with anchorage lengths of 50, 100, and 150 mm. Because increasing anchorage length reduced the unsupported member length, the observed differences reflect the combined effect of both parameters. Displacements and longitudinal strains were measured using Digital Image Correlation and strain gauges, respectively, and the tests were supplemented by finite element analyses. The configurations produced differences in maximum load and global displacement, although maximum load varied non-monotonically with anchorage length. At the investigated load levels, local longitudinal strains were similar, whereas global displacements differed. The K-5 specimens deformed in the direction opposite to the K-10 and K-15 specimens. Baseline numerical analyses reproduced the observed directions for K-10 and K-15, but not K-5. Reversing the sign of the initial imperfection reproduced the K-5 direction, supporting an interpretation involving two branches of the same global buckling mode; however, the cause of branch selection remained unresolved. The results show that end-fixture configuration should be considered when interpreting experimental and numerical assessments of compressed steel angle members.
- Open Access
- 1 December 2025
- Published by Wydawnictwo Naukowe Gabriel Borowski (WNGB) in Advances in Science and Technology Research Journal
- Vol. 19 (12) , 394-401
Use of carbon fiber fabric for reinforcement of bent hot-rolled steel channels
The widespread application of steel as a structural material in industrial and bridge construction highlights the importance of research into strengthening methods for steel structures made of hot-rolled profiles. This study presents laboratory tests conducted on bent hot-rolled C100 steel...
- 1 December 2025
- Published by Wydawnictwo Naukowe Gabriel Borowski (WNGB) in Advances in Science and Technology Research Journal
- Vol. 19 (12) , 394-401
Open AccessUse of carbon fiber fabric for reinforcement of bent hot-rolled steel channels
The widespread application of steel as a structural material in industrial and bridge construction highlights the importance of research into strengthening methods for steel structures made of hot-rolled profiles. This study presents laboratory tests conducted on bent hot-rolled C100 steel...
- Open Access
- 1 August 2025
- Published by Wydawnictwo Naukowe Gabriel Borowski (WNGB) in Advances in Science and Technology Research Journal
- Vol. 19 (8) , 141-147
Influence of glued steel and composite tapes on the behaviour of axially compressed hot-rolled steel angles
: Hot-rolled steel angles are a profile commonly used as lattice bars in older types of roof girders. With the growing popularity of photovoltaic installations mounted on the roofs of steel halls, steel structure designers often face the problem of exceeding the load-bearing capacity of...
- 1 August 2025
- Published by Wydawnictwo Naukowe Gabriel Borowski (WNGB) in Advances in Science and Technology Research Journal
- Vol. 19 (8) , 141-147
Open AccessInfluence of glued steel and composite tapes on the behaviour of axially compressed hot-rolled steel angles
: Hot-rolled steel angles are a profile commonly used as lattice bars in older types of roof girders. With the growing popularity of photovoltaic installations mounted on the roofs of steel halls, steel structure designers often face the problem of exceeding the load-bearing capacity of...
- 28 April 2025
- Published by Index Copernicus in Przegląd Budowlany
- Vol. 96 (2) , 181-183
Badanie wpływu zastosowania taśm stalowychi kompozytowych na ograniczenie przemieszczeńi odkształceń zginanych stalowych profili cienkościennych
Stalowe profile cienkościenne typu sigma są powszechniewykorzystywane jako płatwie w halach stalowych. Wrazze wzrostem popularności instalacji fotowoltaicznych montowanychna dachach hal stalowych projektanci konstrukcji stalowych częstomierzą się z problemem przekroczenia stanów granicznych nośnościlub użytkowalności w płatwiach dachowych lub innych elementachkonstrukcyjnych. W związku z tym, w niniejszej pracy, przedstawionobadania laboratoryjne 10 zginanych stalowych profili cienkościennychtypu sigma (8 wzmacnianych techniką klejenia i nitowaniataśm stalowych oraz klejenia taśm i mat kompozytowych oraz2 referencyjnych). W trakcie badań mierzono odkształcenia za pomocątensometrów elektrooporowych oraz przemieszczenia za pomocąsystemu Aramis. Uzyskane wyniki wykazały korzystny wpływzastosowania zaproponowanych materiałów na ograniczenie przemieszczeńi odkształceń badanych elementów.
- 28 April 2025
- Published by Index Copernicus in Przegląd Budowlany
- Vol. 96 (2) , 181-183
Badanie wpływu zastosowania taśm stalowychi kompozytowych na ograniczenie przemieszczeńi odkształceń zginanych stalowych profili cienkościennych
Stalowe profile cienkościenne typu sigma są powszechniewykorzystywane jako płatwie w halach stalowych. Wrazze wzrostem popularności instalacji fotowoltaicznych montowanychna dachach hal stalowych projektanci konstrukcji stalowych częstomierzą się z problemem przekroczenia stanów granicznych nośnościlub użytkowalności w płatwiach dachowych lub innych elementachkonstrukcyjnych. W związku z tym, w niniejszej pracy, przedstawionobadania laboratoryjne 10 zginanych stalowych profili cienkościennychtypu sigma (8 wzmacnianych techniką klejenia i nitowaniataśm stalowych oraz klejenia taśm i mat kompozytowych oraz2 referencyjnych). W trakcie badań mierzono odkształcenia za pomocątensometrów elektrooporowych oraz przemieszczenia za pomocąsystemu Aramis. Uzyskane wyniki wykazały korzystny wpływzastosowania zaproponowanych materiałów na ograniczenie przemieszczeńi odkształceń badanych elementów.
- Open Access
- 22 July 2024
- Published by Wydawnictwo Naukowe Gabriel Borowski (WNGB) in Advances in Science and Technology Research Journal
- Vol. 18 (6) , 206-217
Determination of the Load-Bearing Capacity of the Bonded Joint of Hot-Dip Galvanised Steel Elements with CFRP Fabric – Pilot Laboratory and Numerical Investigations
In this paper, an attempt was made to determine the load-bearing capacity of a bonded joint of galvanized steel elements with CFRP fabric. This issue is extremely relevant to the use of bonded carbon fiber fabric as a mean of reinforcing hot-dip galvanized steel structures. This technique is used...
- 22 July 2024
- Published by Wydawnictwo Naukowe Gabriel Borowski (WNGB) in Advances in Science and Technology Research Journal
- Vol. 18 (6) , 206-217
Open AccessDetermination of the Load-Bearing Capacity of the Bonded Joint of Hot-Dip Galvanised Steel Elements with CFRP Fabric – Pilot Laboratory and Numerical Investigations
In this paper, an attempt was made to determine the load-bearing capacity of a bonded joint of galvanized steel elements with CFRP fabric. This issue is extremely relevant to the use of bonded carbon fiber fabric as a mean of reinforcing hot-dip galvanized steel structures. This technique is used...
- Open Access
The Influence of Using Steel Tapes and Composite Materials on Reinforcing Hot-Rolled Steel Profiles
Steel structure designers frequently encounter the need to reinforce hot-rolled compressed steel elements. This is particularly common in the case of compressed truss bars in steel truss girders. Typically, reinforcement is designed using bars or flat bars welded to the compressed element. However, welding technology is not always feasible in existing and operational steel halls due to fire safety concerns. To address this challenge, researchers investigated alternative reinforcement methods using bonded steel and CFRPs (carbon fiber-reinforced polymers/plastics) tapes. Laboratory tests and numerical analyses were conducted. Eleven 1.5 m long specimens made of 50 × 50 × 4 angle iron from S235 steel were subjected to axial compression testing. The test samples included three unreinforced samples, three samples reinforced with steel tape bonded using SikaDur-30 adhesive, and five samples reinforced with CFRP tape (SikaDur-30 adhesive was used for bonding in three cases, and 3M VHB GPH-160GF tape in two cases). The research conducted indicates that reinforcement using bonded steel tapes is the most effective method for limiting vertical displacements and deformations, as well as increasing the load-bearing capacity of the tested angles by 28.6% compared to the reference elements. Considering the high cost of composite tapes, this is valuable information from an economic analysis perspective. The absence of steel tape delamination suggests that the bonding technique can be successfully employed in this reinforcement method and can replace welding, for example in facilities where there is a high fire hazard.
Open AccessThe Influence of Using Steel Tapes and Composite Materials on Reinforcing Hot-Rolled Steel Profiles
Steel structure designers frequently encounter the need to reinforce hot-rolled compressed steel elements. This is particularly common in the case of compressed truss bars in steel truss girders. Typically, reinforcement is designed using bars or flat bars welded to the compressed element. However, welding technology is not always feasible in existing and operational steel halls due to fire safety concerns. To address this challenge, researchers investigated alternative reinforcement methods using bonded steel and CFRPs (carbon fiber-reinforced polymers/plastics) tapes. Laboratory tests and numerical analyses were conducted. Eleven 1.5 m long specimens made of 50 × 50 × 4 angle iron from S235 steel were subjected to axial compression testing. The test samples included three unreinforced samples, three samples reinforced with steel tape bonded using SikaDur-30 adhesive, and five samples reinforced with CFRP tape (SikaDur-30 adhesive was used for bonding in three cases, and 3M VHB GPH-160GF tape in two cases). The research conducted indicates that reinforcement using bonded steel tapes is the most effective method for limiting vertical displacements and deformations, as well as increasing the load-bearing capacity of the tested angles by 28.6% compared to the reference elements. Considering the high cost of composite tapes, this is valuable information from an economic analysis perspective. The absence of steel tape delamination suggests that the bonding technique can be successfully employed in this reinforcement method and can replace welding, for example in facilities where there is a high fire hazard.
- Open Access
- 16 August 2023
- Published by Wydawnictwo Naukowe Gabriel Borowski (WNGB) in Advances in Science and Technology Research Journal
- Vol. 17 (4) , 282-289
Analysis of the Impact of Using CFRP Tapes on the Performance of Bent Thin-Walled Beams Connected with a Sandwich Panel – Pilot Studies
The heightening use of thin-walled steel structures necessitates the search for fast and efficient methods of their reinforcement. One solution might be the application of bonded composite tapes. The author of the work has conducted a number of studies so far, which showed a beneficial effect of...
- 16 August 2023
- Published by Wydawnictwo Naukowe Gabriel Borowski (WNGB) in Advances in Science and Technology Research Journal
- Vol. 17 (4) , 282-289
Open AccessAnalysis of the Impact of Using CFRP Tapes on the Performance of Bent Thin-Walled Beams Connected with a Sandwich Panel – Pilot Studies
The heightening use of thin-walled steel structures necessitates the search for fast and efficient methods of their reinforcement. One solution might be the application of bonded composite tapes. The author of the work has conducted a number of studies so far, which showed a beneficial effect of...
- 30 June 2023
- Published by Polish Academy of Sciences Chancellery in Archives of Civil Engineering
- Vol. 69 (2) , 311-323
Impact of numerical modelling of kinematic and static boundary conditions on stability of cold-formed sigma beam
- 30 June 2023
- Published by Polish Academy of Sciences Chancellery in Archives of Civil Engineering
- Vol. 69 (2) , 311-323
Impact of numerical modelling of kinematic and static boundary conditions on stability of cold-formed sigma beam
- Open Access
Investigation of an Effective Anchoring Length of CFRP Tapes Used to Strengthen Steel Thin-Walled Beams with a Rectangular Cross-Section Subjected to Four-Point Bending
In order to design an optimal reinforcement of steel thin-walled beams with composite materials, it is worth analyzing two important, although often overlooked issues, which are the selection of the appropriate thickness of the adhesive layer and the effective anchoring length of the composite tape. This paper, which is part of a wider laboratory study devoted to the strengthening of thin-walled steel profiles, focuses on the second issue. The paper involves a description of laboratory four-point bending tests during which ten thin-walled steel beams made of a rectangular section with dimensions of 120 × 60 × 3 and a length of 3 m were tested. Two beams were taken as reference beams, and the other eight were reinforced using Sika CarboDur S512 carbon fiber composite tape, assuming four different effective anchorage lengths. The impact of the length of the anchoring of the composite tape on the value of the displacements and strains of the tested beams and on the value of the destructive load that caused tape detachment was analyzed. The following phase was numerical analyses carried out in the Abaqus program, which showed high consistency with the results of laboratory tests. In reference to the conducted tests, it was observed that the increase in the anchoring length of the composite tape has a slight impact on the change in the value of strains and displacements in the tested beams. Nevertheless, the increase in the effective anchorage length has a significant impact on the load value at which the composite tapes are detached from the surface of the steel thin-walled beam.
Open AccessInvestigation of an Effective Anchoring Length of CFRP Tapes Used to Strengthen Steel Thin-Walled Beams with a Rectangular Cross-Section Subjected to Four-Point Bending
In order to design an optimal reinforcement of steel thin-walled beams with composite materials, it is worth analyzing two important, although often overlooked issues, which are the selection of the appropriate thickness of the adhesive layer and the effective anchoring length of the composite tape. This paper, which is part of a wider laboratory study devoted to the strengthening of thin-walled steel profiles, focuses on the second issue. The paper involves a description of laboratory four-point bending tests during which ten thin-walled steel beams made of a rectangular section with dimensions of 120 × 60 × 3 and a length of 3 m were tested. Two beams were taken as reference beams, and the other eight were reinforced using Sika CarboDur S512 carbon fiber composite tape, assuming four different effective anchorage lengths. The impact of the length of the anchoring of the composite tape on the value of the displacements and strains of the tested beams and on the value of the destructive load that caused tape detachment was analyzed. The following phase was numerical analyses carried out in the Abaqus program, which showed high consistency with the results of laboratory tests. In reference to the conducted tests, it was observed that the increase in the anchoring length of the composite tape has a slight impact on the change in the value of strains and displacements in the tested beams. Nevertheless, the increase in the effective anchorage length has a significant impact on the load value at which the composite tapes are detached from the surface of the steel thin-walled beam.
- Open Access
Influence of Adhesive Layer Thickness on the Effectiveness of Reinforcing Thin-Walled Steel Beams with CFRP Tapes—A Pilot Study
When reinforcing thin-walled steel members with composite tapes, two issues often overlooked in published scientific papers should be considered, namely the correct thickness of the adhesive layer and the optimum bond length of the CFRP tape. In this article, the authors focused on the first of these issues. For this purpose, eight beams with a thin-walled box cross-section and a length of 3 m were subjected to bending in a four-point scheme. Six beams were reinforced with Sika CarboDur S512 composite tape, and two beams without reinforcement were tested as reference members. Three thicknesses of the adhesive layer (SikaDur-30) were analyzed: 0.6 mm, 1.3 mm and 1.75 mm. In addition to examining the effect of the thickness of the adhesive layer on displacements and deformations of thin-walled steel members, the load value at which the composite tape peeled off was also analyzed. Numerical analyses were then carried out in Abaqus, the outcomes of which showed good agreement with the laboratory results. Both numerical and laboratory results have shown that the thickness of the adhesive layer had a minor effect on the reduction in deformation and displacement of the tested beams. At the same time, with the increase in the thickness of the adhesive layer, the value of the load at which the CFRP tapes detached from the beam surface significantly decreased.
Open AccessInfluence of Adhesive Layer Thickness on the Effectiveness of Reinforcing Thin-Walled Steel Beams with CFRP Tapes—A Pilot Study
When reinforcing thin-walled steel members with composite tapes, two issues often overlooked in published scientific papers should be considered, namely the correct thickness of the adhesive layer and the optimum bond length of the CFRP tape. In this article, the authors focused on the first of these issues. For this purpose, eight beams with a thin-walled box cross-section and a length of 3 m were subjected to bending in a four-point scheme. Six beams were reinforced with Sika CarboDur S512 composite tape, and two beams without reinforcement were tested as reference members. Three thicknesses of the adhesive layer (SikaDur-30) were analyzed: 0.6 mm, 1.3 mm and 1.75 mm. In addition to examining the effect of the thickness of the adhesive layer on displacements and deformations of thin-walled steel members, the load value at which the composite tape peeled off was also analyzed. Numerical analyses were then carried out in Abaqus, the outcomes of which showed good agreement with the laboratory results. Both numerical and laboratory results have shown that the thickness of the adhesive layer had a minor effect on the reduction in deformation and displacement of the tested beams. At the same time, with the increase in the thickness of the adhesive layer, the value of the load at which the CFRP tapes detached from the beam surface significantly decreased.