Jens Hartig
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Jens Hartig has a total of 27 co-authors. Here are the top co-authors by number of shared publications:
- Peer Haller
Institute of Steel and Timber Construction, Technische Universität Dresden, Dresden, Germany
10 shared publications Peer Haller
Institute of Steel and Timber Construction, Technische Universität Dresden, Dresden, Germany
6 shared publications- Andreas Heiduschke
Hess Corporation
4 shared publications - Jörg Wehsener
Institute of Steel and Timber Construction, Technische Universität Dresden, Dresden, Germany
3 shared publications - Jörg Wehsener
Technische Universität Dresden, Institut für Stahl- und Holzbau, 01062 Dresden
3 shared publications - Dipl.-Ing. Robert Putzger
Dresden University of Technology
2 shared publications
Latest Publications
- 13 December 2023
- Published by Taylor & Francis in Wood Material Science & Engineering
- Vol. 19 (3) , 738-744
Investigations on the thermo-mechanical behaviour of densified veneer wood for cryogenic applications
- 13 December 2023
- Published by Taylor & Francis in Wood Material Science & Engineering
- Vol. 19 (3) , 738-744
Investigations on the thermo-mechanical behaviour of densified veneer wood for cryogenic applications
- Open Access
- 18 November 2023
- Published by Springer Nature in European Journal of Wood and Wood Products
- Vol. 82 (2) , 329-339
Combustion characteristics and mechanical properties of wood impregnated with a paraffinic phase change material
In this contribution, investigations towards multifunctional wood and timber elements impregnated with phase change materials (PCM) are presented. The purpose of the PCM impregnation is a passive air-conditioning by structural timber elements like beams, walls or ceilings and non-structural elements like flooring or wall panels. PCM have the ability to take up substantial thermal energy within a narrow, latent temperature range without increasing their temperature. The high specific heat capacity combined with low additional mass can improve the room climate in timber buildings, which have often, especially in the summer, unpleasant temperature amplitudes without active air-conditioning due to low thermal mass.In order to produce PCM-impregnated timber elements, several investigations are performed. As a first aspect, investigations related to the mechanical behaviour of PCM-impregnated wood are presented. The investigations show that in its solid state the PCM can improve the mechanical properties. In the liquid state of the PCM, the mechanical properties of the impregnated wood are on the level of PCM-free wood. A second aspect, which was investigated, is the combustion behaviour. Investigations with cone calorimetry showed that directly flamed PCM-impregnated wood acts as fire accelerant. However, reaction to fire tests of laminated non-structural elements also showed that a proper protection from direct contact to fire could enable a safe use of PCM-impregnated wood in construction elements.
- 18 November 2023
- Published by Springer Nature in European Journal of Wood and Wood Products
- Vol. 82 (2) , 329-339
Open AccessCombustion characteristics and mechanical properties of wood impregnated with a paraffinic phase change material
In this contribution, investigations towards multifunctional wood and timber elements impregnated with phase change materials (PCM) are presented. The purpose of the PCM impregnation is a passive air-conditioning by structural timber elements like beams, walls or ceilings and non-structural elements like flooring or wall panels. PCM have the ability to take up substantial thermal energy within a narrow, latent temperature range without increasing their temperature. The high specific heat capacity combined with low additional mass can improve the room climate in timber buildings, which have often, especially in the summer, unpleasant temperature amplitudes without active air-conditioning due to low thermal mass.In order to produce PCM-impregnated timber elements, several investigations are performed. As a first aspect, investigations related to the mechanical behaviour of PCM-impregnated wood are presented. The investigations show that in its solid state the PCM can improve the mechanical properties. In the liquid state of the PCM, the mechanical properties of the impregnated wood are on the level of PCM-free wood. A second aspect, which was investigated, is the combustion behaviour. Investigations with cone calorimetry showed that directly flamed PCM-impregnated wood acts as fire accelerant. However, reaction to fire tests of laminated non-structural elements also showed that a proper protection from direct contact to fire could enable a safe use of PCM-impregnated wood in construction elements.
- Open Access
- 25 October 2022
- Published by Taylor & Francis in Wood Material Science & Engineering
- Vol. 18 (1) , 19-28
Impregnation of wood with a paraffinic phase change material for increasing heat capacity
In this contribution, the impregnation of wood with a paraffinic phase change material (PCM) is investigated, specifically to increase the heat capacity of solid wood, which significantly influences the thermal inertia when used in buildings. Four wood species (beech, poplar, oak and spruce) were impregnated with different pressure processes in an autoclave. For poplar, up to 480 kg of PCM per m³ of wood was deposited. For beech and spruce, also more than 200 kg of PCM per m³ of wood was achieved. However, oak was hard to impregnate and only about 100 kg of PCM per m³ was deposited. Leakage, which is undesired, occurred for all the wood species, especially for beech, but could be significantly reduced to less than 10% by increasing the viscosity of the PCM. The heat capacity was increased by one order of magnitude compared to clear wood, as measurements with differential scanning calorimetry showed. Simulations with an analytical model demonstrate the potential for damping temperature amplitudes in buildings in the summer month when applying PCM.
- 25 October 2022
- Published by Taylor & Francis in Wood Material Science & Engineering
- Vol. 18 (1) , 19-28
Open AccessImpregnation of wood with a paraffinic phase change material for increasing heat capacity
In this contribution, the impregnation of wood with a paraffinic phase change material (PCM) is investigated, specifically to increase the heat capacity of solid wood, which significantly influences the thermal inertia when used in buildings. Four wood species (beech, poplar, oak and spruce) were impregnated with different pressure processes in an autoclave. For poplar, up to 480 kg of PCM per m³ of wood was deposited. For beech and spruce, also more than 200 kg of PCM per m³ of wood was achieved. However, oak was hard to impregnate and only about 100 kg of PCM per m³ was deposited. Leakage, which is undesired, occurred for all the wood species, especially for beech, but could be significantly reduced to less than 10% by increasing the viscosity of the PCM. The heat capacity was increased by one order of magnitude compared to clear wood, as measurements with differential scanning calorimetry showed. Simulations with an analytical model demonstrate the potential for damping temperature amplitudes in buildings in the summer month when applying PCM.
- 7 January 2021
- Published by Walter de Gruyter GmbH in Holzforschung
- Vol. 75 (8) , 742-753
Voxel-based finite element modelling of wood elements based on spatial density and geometry data using computed tomography
In this paper, voxel-based finite element modelling based on spatial geometry and density data is applied to simulate the detailed stress and strain distribution in a large wood element. As example, a moulded wooden tube with a length of 3 m and a diameter of 0.3 m is examined. Gamma-ray computed tomography is used to obtain both, its actual geometric shape and spatial density distribution. Correlation functions (R2 ≈ 0.6) between density and elastic material properties are experimentally determined and serve as link for defining the non-uniform distribution of the material properties in the finite element model. Considering the geometric imperfections and spatial variation of the material properties, a detailed analysis of the stress and strain distribution of a wood element is performed. Additionally, a non-destructive axial compression test is applied on the wooden tube to analyse the load-bearing behaviour. By means of digital image correlation, the deformation of the surface is obtained, which also serves for validation of the finite element model in terms of strain distributions.
- 7 January 2021
- Published by Walter de Gruyter GmbH in Holzforschung
- Vol. 75 (8) , 742-753
Voxel-based finite element modelling of wood elements based on spatial density and geometry data using computed tomography
In this paper, voxel-based finite element modelling based on spatial geometry and density data is applied to simulate the detailed stress and strain distribution in a large wood element. As example, a moulded wooden tube with a length of 3 m and a diameter of 0.3 m is examined. Gamma-ray computed tomography is used to obtain both, its actual geometric shape and spatial density distribution. Correlation functions (R2 ≈ 0.6) between density and elastic material properties are experimentally determined and serve as link for defining the non-uniform distribution of the material properties in the finite element model. Considering the geometric imperfections and spatial variation of the material properties, a detailed analysis of the stress and strain distribution of a wood element is performed. Additionally, a non-destructive axial compression test is applied on the wooden tube to analyse the load-bearing behaviour. By means of digital image correlation, the deformation of the surface is obtained, which also serves for validation of the finite element model in terms of strain distributions.
- 19 November 2018
- Published by Emerald Publishing in Engineering Computations
- Vol. 36 (1) , 2-24
Moisture-dependent thermo-mechanical constitutive modeling of wood
The purpose of this study is the numerical investigation of densification and molding processes of wood. Providing theoretical and numerical approaches with respect to a consistent multi-physical finite element method framework are further goals of this research. Constitutive phenomenological descriptions of the thermo-mechanical and moisture-dependent material characteristics of wood are introduced. Special focus is given to a consistent hygro-thermo-mechanical modeling at finite deformations to capture the realistic material behavior of wood, especially when it is subjected to densification and molding processes. Realistic theoretical formulations of different hygro-thermo-mechanical processes are provided. A successful numerical modeling is demonstrated for beech wood by validation at experimental findings. The constitutive laws and numerical findings are new, as they govern a multi-physical large deformation framework and are applied to the advanced technology of densification and molding of wood.
- 19 November 2018
- Published by Emerald Publishing in Engineering Computations
- Vol. 36 (1) , 2-24
Moisture-dependent thermo-mechanical constitutive modeling of wood
The purpose of this study is the numerical investigation of densification and molding processes of wood. Providing theoretical and numerical approaches with respect to a consistent multi-physical finite element method framework are further goals of this research. Constitutive phenomenological descriptions of the thermo-mechanical and moisture-dependent material characteristics of wood are introduced. Special focus is given to a consistent hygro-thermo-mechanical modeling at finite deformations to capture the realistic material behavior of wood, especially when it is subjected to densification and molding processes. Realistic theoretical formulations of different hygro-thermo-mechanical processes are provided. A successful numerical modeling is demonstrated for beech wood by validation at experimental findings. The constitutive laws and numerical findings are new, as they govern a multi-physical large deformation framework and are applied to the advanced technology of densification and molding of wood.
- 1 November 2018
- Published by Wiley in Bautechnik
- Vol. 95 (11) , 775-786
Static verification and experimental investigations on slotted connections with GRP plates and dowels for engineered timber structures
- 1 November 2018
- Published by Wiley in Bautechnik
- Vol. 95 (11) , 775-786
Static verification and experimental investigations on slotted connections with GRP plates and dowels for engineered timber structures
- 1 June 2018
- Published by Elsevier in Construction and Building Materials
- Vol. 174, 547-558
Investigations on lateral vehicle impact on moulded wooden tubes made of beech (Fagus sylvatica L.)
- 1 June 2018
- Published by Elsevier in Construction and Building Materials
- Vol. 174, 547-558
Investigations on lateral vehicle impact on moulded wooden tubes made of beech (Fagus sylvatica L.)
- 9 November 2016
- Published by Springer Nature in European Journal of Wood and Wood Products
- Vol. 75 (2) , 281-284
Thermo-hydro-mechanical behaviour of acetylated wood: swelling, compression set recovery and mouldability
- 9 November 2016
- Published by Springer Nature in European Journal of Wood and Wood Products
- Vol. 75 (2) , 281-284
Thermo-hydro-mechanical behaviour of acetylated wood: swelling, compression set recovery and mouldability
- 1 November 2016
- Published by Elsevier in Construction and Building Materials
- Vol. 126, 527-536
Experimental and theoretical investigations on moulded wooden tubes made of beech (Fagus sylvatica L.)
- 1 November 2016
- Published by Elsevier in Construction and Building Materials
- Vol. 126, 527-536
Experimental and theoretical investigations on moulded wooden tubes made of beech (Fagus sylvatica L.)
- 8 January 2015
- Published by Wiley in Bautechnik
- Vol. 92 (1) , 36-39
Formholzrohre aus Buche