Sambhu Nath Pradhan
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Sambhu Nath Pradhan has a total of 15 co-authors. Here are the top co-authors by number of shared publications:
- Abhishek Bhattacharjee
Department of Electronics and Communication Engineering, National Institute of Technology, Agartala, Tripura, India
2 shared publications - Kaushik Das
NIT Jamshedpur
2 shared publications - Somnath Roy Choudhury
Department of ECE, National Institute of Technology Agartala, Agartala 799046, India
2 shared publications - Vivek Kumar Singh
Department of ECE, National Institute of Technology, Agartala, Agartala, Tripura 799046, India
2 shared publications - Abhishek Nag
Department of ECE, National Institute of Technology, Agartala, Agartala, India
1 shared publication - Angshuman Chakraborty
Department of ECE, N.I.T Agartala, Agartala, Tripura, India
1 shared publication
Latest Publications
- 12 September 2024
- Published by World Scientific Pub Co Pte Ltd in Journal of Circuits, Systems and Computers
- Vol. 33 (18)
Efficient Hardware Architecture Design of Radix-22 Fast Fourier Transform Using Coordinate Rotation Digital Computer
The fast Fourier transform (FFT) is a widely used algorithm for computing the discrete Fourier transform (DFT) in real-time signal processing. Achieving high performance with minimal resource usage is crucial for any real-time application. This paper introduces an architecture based on coordinate rotation digital computer (CORDIC) for implementing a radix-[ ] FFT. Traditional FFT implementations require complex twiddle factor multiplications, which is not cost-effective in terms of hardware utilization. To address this issue, we have proposed a radix-8 CORDIC-based approach integrated with FFT computation. The proposed radix-8 CORDIC requires fewer stages than the conventional radix-2 CORDIC, enhancing computational efficiency and reducing hardware utilization. The feedforward radix-[ ] FFT architecture is presented where the butterflies of the FFT are computed with the help of radix-8 CORDIC. A total of three FFT architectures are developed supporting 16-, 1024- and 2048-point FFTs. The proposed FFT architectures are developed using Verilog-HDL code and implemented on a Virtex-7 field-programmable gate array (FPGA). The FPGA-based radix-[ ] FFT achieves a clock frequency of 323.4[ ]MHz and utilizes minimal FPGA resources. Processing of 2048 data samples takes only 4.06[ ][ ]S by the proposed FPGA-based design. Additionally, two ASICs have been designed: the 1024-point FFT ASIC occupies an area of 1.079[ ]mm2, and the 2048-point FFT ASIC occupies an area of 1.544 mm2. The proposed FFT ASICs have better-normalized area per FFT and energy per FFT than the state-of-the-art designs.
- 12 September 2024
- Published by World Scientific Pub Co Pte Ltd in Journal of Circuits, Systems and Computers
- Vol. 33 (18)
Efficient Hardware Architecture Design of Radix-22 Fast Fourier Transform Using Coordinate Rotation Digital Computer
The fast Fourier transform (FFT) is a widely used algorithm for computing the discrete Fourier transform (DFT) in real-time signal processing. Achieving high performance with minimal resource usage is crucial for any real-time application. This paper introduces an architecture based on coordinate rotation digital computer (CORDIC) for implementing a radix-[ ] FFT. Traditional FFT implementations require complex twiddle factor multiplications, which is not cost-effective in terms of hardware utilization. To address this issue, we have proposed a radix-8 CORDIC-based approach integrated with FFT computation. The proposed radix-8 CORDIC requires fewer stages than the conventional radix-2 CORDIC, enhancing computational efficiency and reducing hardware utilization. The feedforward radix-[ ] FFT architecture is presented where the butterflies of the FFT are computed with the help of radix-8 CORDIC. A total of three FFT architectures are developed supporting 16-, 1024- and 2048-point FFTs. The proposed FFT architectures are developed using Verilog-HDL code and implemented on a Virtex-7 field-programmable gate array (FPGA). The FPGA-based radix-[ ] FFT achieves a clock frequency of 323.4[ ]MHz and utilizes minimal FPGA resources. Processing of 2048 data samples takes only 4.06[ ][ ]S by the proposed FPGA-based design. Additionally, two ASICs have been designed: the 1024-point FFT ASIC occupies an area of 1.079[ ]mm2, and the 2048-point FFT ASIC occupies an area of 1.544 mm2. The proposed FFT ASICs have better-normalized area per FFT and energy per FFT than the state-of-the-art designs.
- 11 April 2023
- Published by Elsevier in Integration
- Vol. 91, 153-164
Hardware architecture design for complementary ensemble empirical mode decomposition algorithm
- 11 April 2023
- Published by Elsevier in Integration
- Vol. 91, 153-164
Hardware architecture design for complementary ensemble empirical mode decomposition algorithm
- 1 March 2022
- Published by Wiley in International Journal of Circuit Theory and Applications
- Vol. 50 (6) , 2271-2286
Shared reduced ordered binary decision diagram‐based thermal‐aware network synthesis
Summary: In this work, a multi‐objective algorithm based on nondominated sorting genetic algorithm‐II (NSGA‐II) for thermal‐aware realization of a combinational logic network has been implemented. Input variable ordering of shared reduced ordered binary decision diagram (SROBDD) is done using NSGA‐II such that resulting combinational circuit generates low hotspots by suitable power density distribution. Simultaneous co‐optimization among area, power, and temperature is important in the higher levels of electronic circuit design to reduce the cooling cost. Using a multi‐objective algorithm (NSGA‐II), an effort is made to decrease the temperature by co‐optimization between the power density, area, and power simultaneously. Microelectronics Center of North Carolina (MCNC) benchmark circuits are tested using the proposed approach and an improvement of 13.65% in the silicon area and up to 10% in power dissipation, and 2.72% peak temperature reduction is reported in comparison to existing literature. HotSpot tool and Cadence Innovus are used to determine the peak temperature, actual silicon chip area, and power dissipation of algorithmic optimized solutions.
- 1 March 2022
- Published by Wiley in International Journal of Circuit Theory and Applications
- Vol. 50 (6) , 2271-2286
Shared reduced ordered binary decision diagram‐based thermal‐aware network synthesis
Summary: In this work, a multi‐objective algorithm based on nondominated sorting genetic algorithm‐II (NSGA‐II) for thermal‐aware realization of a combinational logic network has been implemented. Input variable ordering of shared reduced ordered binary decision diagram (SROBDD) is done using NSGA‐II such that resulting combinational circuit generates low hotspots by suitable power density distribution. Simultaneous co‐optimization among area, power, and temperature is important in the higher levels of electronic circuit design to reduce the cooling cost. Using a multi‐objective algorithm (NSGA‐II), an effort is made to decrease the temperature by co‐optimization between the power density, area, and power simultaneously. Microelectronics Center of North Carolina (MCNC) benchmark circuits are tested using the proposed approach and an improvement of 13.65% in the silicon area and up to 10% in power dissipation, and 2.72% peak temperature reduction is reported in comparison to existing literature. HotSpot tool and Cadence Innovus are used to determine the peak temperature, actual silicon chip area, and power dissipation of algorithmic optimized solutions.
- 1 February 2022
- Published by Springer Nature in Journal of Electronic Testing
- Vol. 38 (1) , 91-105
Design of Power Gated SRAM Cell for Reducing the NBTI Effect and Leakage Power Dissipation During the Hold Operation
- 1 February 2022
- Published by Springer Nature in Journal of Electronic Testing
- Vol. 38 (1) , 91-105
Design of Power Gated SRAM Cell for Reducing the NBTI Effect and Leakage Power Dissipation During the Hold Operation
- 5 December 2021
- Published by Taylor & Francis in IETE Technical Review
- Vol. 39 (6) , 1395-1409
Power-Aware Testing for Maximum Fault Coverage in Analog and Digital Circuits Simultaneously
In this paper, a method for maximum fault coverage with minimum power dissipation, during the testing of analog and digital circuits of mixed-signal System-on-Chip (SOC) simultaneously using Genetic Algorithm, (GA) is proposed. Mixed-signal SOC consists mainly of an analog block, a digital block and a DAC/ADC (Digital to Analog Converter/Analog to Digital Converter). Due to the presence of analog and digital circuits in mixed-signal SOCs, the testing procedure is difficult from that of only analog or digital circuit testing. Here stuck at 0/1 faults are considered for digital circuits, and stuck open/short faults are considered for analog circuits. In analog testing fault modeling, fault injection and fault simulation are done. The outputs of the analog block and some independent digital signals are given to the digital block. The GA-based approach is used for power-aware ordering of test patterns considering pattern dependency on previous patterns at the input of digital block as input patterns. The effect of noise on analog test signals has also been investigated here with the area analysis of the circuit. An average of 92.43% fault coverage and 13.56% maximum power saving is achieved when this methodology is applied to ITC 97 (Analog block) and ISCAS 85 (Digital block) benchmark circuits, respectively. A trade-off between fault coverage and power dissipation has been presented.
- 5 December 2021
- Published by Taylor & Francis in IETE Technical Review
- Vol. 39 (6) , 1395-1409
Power-Aware Testing for Maximum Fault Coverage in Analog and Digital Circuits Simultaneously
In this paper, a method for maximum fault coverage with minimum power dissipation, during the testing of analog and digital circuits of mixed-signal System-on-Chip (SOC) simultaneously using Genetic Algorithm, (GA) is proposed. Mixed-signal SOC consists mainly of an analog block, a digital block and a DAC/ADC (Digital to Analog Converter/Analog to Digital Converter). Due to the presence of analog and digital circuits in mixed-signal SOCs, the testing procedure is difficult from that of only analog or digital circuit testing. Here stuck at 0/1 faults are considered for digital circuits, and stuck open/short faults are considered for analog circuits. In analog testing fault modeling, fault injection and fault simulation are done. The outputs of the analog block and some independent digital signals are given to the digital block. The GA-based approach is used for power-aware ordering of test patterns considering pattern dependency on previous patterns at the input of digital block as input patterns. The effect of noise on analog test signals has also been investigated here with the area analysis of the circuit. An average of 92.43% fault coverage and 13.56% maximum power saving is achieved when this methodology is applied to ITC 97 (Analog block) and ISCAS 85 (Digital block) benchmark circuits, respectively. A trade-off between fault coverage and power dissipation has been presented.
- Open Access
- 17 March 2021
- Published by Springer Nature in Research Square
Printed Circuit Board Design of a Low Power, Lightweight and Compact 3D Structured Air Quality Monitoring System
This paper presents wireless integrated compact, lightweight and portable printed circuit board (PCB) device of air quality monitoring system (AQMS). The system is fabricated in double-sided three PCBs to observe real-time data of CO2, CO, NO2 and weather parameters. For the convenience of 3D stacking, the PCB design is built on three boards so that it consumes minimum area. The volume of the entire board is found 110 mm × 80 mm × 24 mm. Strategy of power reduction has been adopted in the design. To reduce power consumption, switching technique is applied to the electronic sensors. This technique is controlled by the use of demultiplexer device. This low power switching technique enhances the battery life of the AQMS structure has been enhanced. Experimental results show that with the chosen batery bank, average power is 1.0588992 Watt during runtime operation of the device. Thus, AQMS runs in safe mode for 33.75 hours continuously using a fully charged power bank. Electrostatic discharge (ESD) protection has been introduced in the PCB to prevent the circuit damage from high voltage during data transmission. The system is capable of being powered by natural resources such as the solar system, which is installed to charge lithium-ion battery. Moreover, the physical weight of the fabricated device is 172gm excluding the weight of the package.
- 17 March 2021
- Published by Springer Nature in Research Square
Open AccessPrinted Circuit Board Design of a Low Power, Lightweight and Compact 3D Structured Air Quality Monitoring System
This paper presents wireless integrated compact, lightweight and portable printed circuit board (PCB) device of air quality monitoring system (AQMS). The system is fabricated in double-sided three PCBs to observe real-time data of CO2, CO, NO2 and weather parameters. For the convenience of 3D stacking, the PCB design is built on three boards so that it consumes minimum area. The volume of the entire board is found 110 mm × 80 mm × 24 mm. Strategy of power reduction has been adopted in the design. To reduce power consumption, switching technique is applied to the electronic sensors. This technique is controlled by the use of demultiplexer device. This low power switching technique enhances the battery life of the AQMS structure has been enhanced. Experimental results show that with the chosen batery bank, average power is 1.0588992 Watt during runtime operation of the device. Thus, AQMS runs in safe mode for 33.75 hours continuously using a fully charged power bank. Electrostatic discharge (ESD) protection has been introduced in the PCB to prevent the circuit damage from high voltage during data transmission. The system is capable of being powered by natural resources such as the solar system, which is installed to charge lithium-ion battery. Moreover, the physical weight of the fabricated device is 172gm excluding the weight of the package.
- 9 February 2021
- Published by Springer Nature in Wireless Personal Communications
- Vol. 118 (4) , 2921-2940
IoT Based Design of Air Quality Monitoring System Web Server for Android Platform
- 9 February 2021
- Published by Springer Nature in Wireless Personal Communications
- Vol. 118 (4) , 2921-2940
IoT Based Design of Air Quality Monitoring System Web Server for Android Platform
- Open Access
- 30 November 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 8, 216365-216385
An Improved Matrix Generation Framework for Thermal Aware Placement in VLSI
Since hotspots and temperature gradients are reliability and performance-critical issues in processors, thermal awareness finds a vital place in the processor design cycle. Incorporating thermal awareness at the level of physical design, this work proposes a new, fast, and efficient thermal aware placement algorithm called the Thermal Aware Matrix Placement Optimizer (TAMPO) for gate arrays. The algorithm TAMPO is composed of the following components: an improved heat diffusion aware cell arrangement technique called the Initial Matrix Generator (IMaGe), a unique stochastic thermal model based on a thermally improved interpretation of the well known Matrix Synthesis Problem (MSP) and a Simulated Annealing (SA) engine for finding the global optimum solution. TAMPO targets to reduce the peak temperature while maintaining improved values of temperature gradients and the standard deviation in cell temperature with respect to the average chip temperature. This work also presents a methodology, the Co-optimized TAMPO, which extends the concept of TAMPO to simultaneously optimize the thermal attributes and the wirelength of a chip. The proposed algorithms realize a placement in matrix arrangement and upon experimentation on the ISCAS89 benchmark circuits encouraging results have been obtained.
- 30 November 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 8, 216365-216385
Open AccessAn Improved Matrix Generation Framework for Thermal Aware Placement in VLSI
Since hotspots and temperature gradients are reliability and performance-critical issues in processors, thermal awareness finds a vital place in the processor design cycle. Incorporating thermal awareness at the level of physical design, this work proposes a new, fast, and efficient thermal aware placement algorithm called the Thermal Aware Matrix Placement Optimizer (TAMPO) for gate arrays. The algorithm TAMPO is composed of the following components: an improved heat diffusion aware cell arrangement technique called the Initial Matrix Generator (IMaGe), a unique stochastic thermal model based on a thermally improved interpretation of the well known Matrix Synthesis Problem (MSP) and a Simulated Annealing (SA) engine for finding the global optimum solution. TAMPO targets to reduce the peak temperature while maintaining improved values of temperature gradients and the standard deviation in cell temperature with respect to the average chip temperature. This work also presents a methodology, the Co-optimized TAMPO, which extends the concept of TAMPO to simultaneously optimize the thermal attributes and the wirelength of a chip. The proposed algorithms realize a placement in matrix arrangement and upon experimentation on the ISCAS89 benchmark circuits encouraging results have been obtained.
- Open Access
- 28 November 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 7, 172074-172087
DOTFloor–A Diffusion Oriented Time-Improved Floorplanner for Macrocells
This work presents a unique time-efficient and reliable floorplan algorithm DOTFloor (Diffusion Oriented Time-improved Floorplanner), built around a SA (Simulated Annealing) engine and targeted to optimize the peak on-chip temperature along with the traditional design metrics like chip area and wire length. This paper also proposes a novel heat-diffusion based stochastic thermal model called the FATT (Fast Assumption Technique for Temperature) which provides a fast assumption of the degree of hotness during the optimization process. The incorporation of FATT in DOTFloor results in a significant improvement in the run time of the optimization process. Upon experimentation on MCNC (Microelectronics Center of North Carolina) benchmark circuits with the proposed floorplanner, a good optimization in area, wire length metric and peak on-chip temperature with a significant reduction in execution time have been achieved over the existing floorplanning tool, the HotFloorplan.
- 28 November 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 7, 172074-172087
Open AccessDOTFloor–A Diffusion Oriented Time-Improved Floorplanner for Macrocells
This work presents a unique time-efficient and reliable floorplan algorithm DOTFloor (Diffusion Oriented Time-improved Floorplanner), built around a SA (Simulated Annealing) engine and targeted to optimize the peak on-chip temperature along with the traditional design metrics like chip area and wire length. This paper also proposes a novel heat-diffusion based stochastic thermal model called the FATT (Fast Assumption Technique for Temperature) which provides a fast assumption of the degree of hotness during the optimization process. The incorporation of FATT in DOTFloor results in a significant improvement in the run time of the optimization process. Upon experimentation on MCNC (Microelectronics Center of North Carolina) benchmark circuits with the proposed floorplanner, a good optimization in area, wire length metric and peak on-chip temperature with a significant reduction in execution time have been achieved over the existing floorplanning tool, the HotFloorplan.
- 28 November 2013
- Published by Taylor & Francis in International Journal of Electronics Letters
- Vol. 2 (1) , 17-29
A new design of adder circuit for low power and high speed in sub-threshold region
The paper proposes the design of an adder circuit based on a majority function. The adder comprises of only six metal-oxide-semiconductor (MOS) transistors. To make the design to be used invariably in the system with least nanodevice dimensions, some modifications have been done in the existing adder design. Post-layout simulation result at 45 nm Taiwan semiconductor manufacturing company (TSMC) technology confirms that the proposed design works faithfully in sub-threshold regime with appreciable 7% of area reduction and 23.54% power saving with respect to earlier design.
- 28 November 2013
- Published by Taylor & Francis in International Journal of Electronics Letters
- Vol. 2 (1) , 17-29
A new design of adder circuit for low power and high speed in sub-threshold region
The paper proposes the design of an adder circuit based on a majority function. The adder comprises of only six metal-oxide-semiconductor (MOS) transistors. To make the design to be used invariably in the system with least nanodevice dimensions, some modifications have been done in the existing adder design. Post-layout simulation result at 45 nm Taiwan semiconductor manufacturing company (TSMC) technology confirms that the proposed design works faithfully in sub-threshold regime with appreciable 7% of area reduction and 23.54% power saving with respect to earlier design.