Vivek Kumar Singh
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Vivek Kumar Singh has a total of 7 co-authors. Here are the top co-authors by number of shared publications:
Sambhu Nath Pradhan
2 shared publications- Sambhu Nath Pradhan
Department of Electronics and Communication Engineering, National Institute of Technology, Agartala, Tripura, India
2 shared publications Abhishek Bhattacharjee
Department of ECE, National Institute of Technology, Agartala, Agartala, Tripura 799046, India
1 shared publicationAbhishek Nag
Department of ECE, National Institute of Technology, Agartala, Agartala, Tripura 799046, India
1 shared publicationApangshu Das
1 shared publication- Apangshu Das
Bhabha Atomic Research Centre
1 shared publication
Latest Publications
- 25 April 2023
- Published by Springer Nature
- p. 423-430
Temperature Aware Bi-partitioning Multi-level Logic Synthesis
- 25 April 2023
- Published by Springer Nature
- p. 423-430
Temperature Aware Bi-partitioning Multi-level Logic Synthesis
- 24 November 2022
- Published by World Scientific Pub Co Pte Ltd in Journal of Circuits, Systems and Computers
- Vol. 32 (07)
Design and Lifetime Estimation of Low-Power 6-Input Look-Up Table Used in Modern FPGA
Due to technological advancements and voltage scaling, leakage power has become an important concern in CMOS design. The implementation of a field-programmable gate array (FPGA) circuit utilizes a portion of the FPGA’s resources as compared to an application-specific integrated circuit (ASIC). Both the utilized and unutilized parts of the FPGA dissipate leakage power. In this work, two dynamic power gating techniques, PSG-1 and PSG-2, are proposed, which are able to reduce the leakage power of the 6-input look-up table (LUT) used in the Xilinx Spartan-6 series. The obtained results show that the proposed approaches PSG-1 and PSG-2 reduce average leakage power by 54.61% and 66.69%, respectively, at the expense of nominal area and delay overhead. The proposed method is also capable of lowering the average total power of the 6-input LUT. The suggested PSG-1 and PSG-2 approaches reduce average power by 53.75% and 60.83%, respectively. However, header-based power supply gating is extremely vulnerable to the negative-bias temperature instability (NBTI) aging effect and, due to this, the lifetime of the circuit is reduced considerably. Therefore, in this work, lifetime estimation-based analysis is performed by varying the stress probability of the sleep transistor. The results show that the LUT with PSG-1 and PSG-2 techniques has a lifetime of 4.55 years and 11.13 years, respectively. The stress time of the sleep transistor is 50% for the PSG-1 technique and 25% for the PSG-2 technique, respectively.
- 24 November 2022
- Published by World Scientific Pub Co Pte Ltd in Journal of Circuits, Systems and Computers
- Vol. 32 (07)
Design and Lifetime Estimation of Low-Power 6-Input Look-Up Table Used in Modern FPGA
Due to technological advancements and voltage scaling, leakage power has become an important concern in CMOS design. The implementation of a field-programmable gate array (FPGA) circuit utilizes a portion of the FPGA’s resources as compared to an application-specific integrated circuit (ASIC). Both the utilized and unutilized parts of the FPGA dissipate leakage power. In this work, two dynamic power gating techniques, PSG-1 and PSG-2, are proposed, which are able to reduce the leakage power of the 6-input look-up table (LUT) used in the Xilinx Spartan-6 series. The obtained results show that the proposed approaches PSG-1 and PSG-2 reduce average leakage power by 54.61% and 66.69%, respectively, at the expense of nominal area and delay overhead. The proposed method is also capable of lowering the average total power of the 6-input LUT. The suggested PSG-1 and PSG-2 approaches reduce average power by 53.75% and 60.83%, respectively. However, header-based power supply gating is extremely vulnerable to the negative-bias temperature instability (NBTI) aging effect and, due to this, the lifetime of the circuit is reduced considerably. Therefore, in this work, lifetime estimation-based analysis is performed by varying the stress probability of the sleep transistor. The results show that the LUT with PSG-1 and PSG-2 techniques has a lifetime of 4.55 years and 11.13 years, respectively. The stress time of the sleep transistor is 50% for the PSG-1 technique and 25% for the PSG-2 technique, respectively.
- 1 March 2022
- Published by Wiley in International Journal of Circuit Theory and Applications
- Vol. 50 (6) , 2271-2286
Shared reduced ordered binary decision diagram‐based thermal‐aware network synthesis
Summary: In this work, a multi‐objective algorithm based on nondominated sorting genetic algorithm‐II (NSGA‐II) for thermal‐aware realization of a combinational logic network has been implemented. Input variable ordering of shared reduced ordered binary decision diagram (SROBDD) is done using NSGA‐II such that resulting combinational circuit generates low hotspots by suitable power density distribution. Simultaneous co‐optimization among area, power, and temperature is important in the higher levels of electronic circuit design to reduce the cooling cost. Using a multi‐objective algorithm (NSGA‐II), an effort is made to decrease the temperature by co‐optimization between the power density, area, and power simultaneously. Microelectronics Center of North Carolina (MCNC) benchmark circuits are tested using the proposed approach and an improvement of 13.65% in the silicon area and up to 10% in power dissipation, and 2.72% peak temperature reduction is reported in comparison to existing literature. HotSpot tool and Cadence Innovus are used to determine the peak temperature, actual silicon chip area, and power dissipation of algorithmic optimized solutions.
- 1 March 2022
- Published by Wiley in International Journal of Circuit Theory and Applications
- Vol. 50 (6) , 2271-2286
Shared reduced ordered binary decision diagram‐based thermal‐aware network synthesis
Summary: In this work, a multi‐objective algorithm based on nondominated sorting genetic algorithm‐II (NSGA‐II) for thermal‐aware realization of a combinational logic network has been implemented. Input variable ordering of shared reduced ordered binary decision diagram (SROBDD) is done using NSGA‐II such that resulting combinational circuit generates low hotspots by suitable power density distribution. Simultaneous co‐optimization among area, power, and temperature is important in the higher levels of electronic circuit design to reduce the cooling cost. Using a multi‐objective algorithm (NSGA‐II), an effort is made to decrease the temperature by co‐optimization between the power density, area, and power simultaneously. Microelectronics Center of North Carolina (MCNC) benchmark circuits are tested using the proposed approach and an improvement of 13.65% in the silicon area and up to 10% in power dissipation, and 2.72% peak temperature reduction is reported in comparison to existing literature. HotSpot tool and Cadence Innovus are used to determine the peak temperature, actual silicon chip area, and power dissipation of algorithmic optimized solutions.
- 5 December 2021
- Published by Taylor & Francis in IETE Technical Review
- Vol. 39 (6) , 1395-1409
Power-Aware Testing for Maximum Fault Coverage in Analog and Digital Circuits Simultaneously
In this paper, a method for maximum fault coverage with minimum power dissipation, during the testing of analog and digital circuits of mixed-signal System-on-Chip (SOC) simultaneously using Genetic Algorithm, (GA) is proposed. Mixed-signal SOC consists mainly of an analog block, a digital block and a DAC/ADC (Digital to Analog Converter/Analog to Digital Converter). Due to the presence of analog and digital circuits in mixed-signal SOCs, the testing procedure is difficult from that of only analog or digital circuit testing. Here stuck at 0/1 faults are considered for digital circuits, and stuck open/short faults are considered for analog circuits. In analog testing fault modeling, fault injection and fault simulation are done. The outputs of the analog block and some independent digital signals are given to the digital block. The GA-based approach is used for power-aware ordering of test patterns considering pattern dependency on previous patterns at the input of digital block as input patterns. The effect of noise on analog test signals has also been investigated here with the area analysis of the circuit. An average of 92.43% fault coverage and 13.56% maximum power saving is achieved when this methodology is applied to ITC 97 (Analog block) and ISCAS 85 (Digital block) benchmark circuits, respectively. A trade-off between fault coverage and power dissipation has been presented.
- 5 December 2021
- Published by Taylor & Francis in IETE Technical Review
- Vol. 39 (6) , 1395-1409
Power-Aware Testing for Maximum Fault Coverage in Analog and Digital Circuits Simultaneously
In this paper, a method for maximum fault coverage with minimum power dissipation, during the testing of analog and digital circuits of mixed-signal System-on-Chip (SOC) simultaneously using Genetic Algorithm, (GA) is proposed. Mixed-signal SOC consists mainly of an analog block, a digital block and a DAC/ADC (Digital to Analog Converter/Analog to Digital Converter). Due to the presence of analog and digital circuits in mixed-signal SOCs, the testing procedure is difficult from that of only analog or digital circuit testing. Here stuck at 0/1 faults are considered for digital circuits, and stuck open/short faults are considered for analog circuits. In analog testing fault modeling, fault injection and fault simulation are done. The outputs of the analog block and some independent digital signals are given to the digital block. The GA-based approach is used for power-aware ordering of test patterns considering pattern dependency on previous patterns at the input of digital block as input patterns. The effect of noise on analog test signals has also been investigated here with the area analysis of the circuit. An average of 92.43% fault coverage and 13.56% maximum power saving is achieved when this methodology is applied to ITC 97 (Analog block) and ISCAS 85 (Digital block) benchmark circuits, respectively. A trade-off between fault coverage and power dissipation has been presented.