Yasin Yilmaz
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Yasin Yilmaz has a total of 15 co-authors. Here are the top co-authors by number of shared publications:
Zekeriya Girgin
3 shared publications- Ersin Demir
Department of Mechatronics Engineering, Pamukkale University, Denizli, Türkiye
2 shared publications - Gunay Anlas
Boğaziçi University
2 shared publications Hasan Çallıoğlu
Department of Mechanical Engineering, Faculty of Engineering, Pamukkale University, Kinikli Campus, 20070 Denizli, Turkey
2 shared publicationsSavas Evran
Vocational School of Technical Sciences, Canakkale Onsekiz Mart University, 17100 Canakkale, Turkey
2 shared publications- Savaş EVRAN
Department of Jewelry and Jewelry Design, Faculty of Applied Sciences, Marmara University, Istanbul 34865, Turkey
2 shared publications
Latest Publications
- 27 February 2023
- Published by Springer Nature in Sādhanā
- Vol. 48 (1) , 1-13
An experimental study on low velocity impact characteristics of glass fiber reinforced epoxy nanocomposites
- 27 February 2023
- Published by Springer Nature in Sādhanā
- Vol. 48 (1) , 1-13
An experimental study on low velocity impact characteristics of glass fiber reinforced epoxy nanocomposites
- 31 August 2022
- Published by ALKU Fen Bilimleri Dergisi, Alanya Alaaddin Keykubat University in ALKÜ Fen Bilimleri Dergisi
- Vol. 4 (2) , 63-70
Effects of Fiber Type and Number of Layers on Modal Analysis of Laminated Composite Plates
The goal of this study is to examine the effects of fiber type and number of layers on modal analysis oflaminated composite plates using finite element and Taguchi methods. Modal analysis was carried out byfinite element software ANSYS in accordance with L9 orthogonal array which has two control factors suchas fiber types and number of layers. Optimal levels of fiber types and number of layers were determinedusing analysis of Signal-to-Noise ratio, while importance levels and percentage effects of control factorswere performed using analysis of variance at 95% confidence level. According to results obtained from thisstudy, the maximum fundamental natural frequency value was calculated using boron-fiber-reinforcedlaminated composite plates with three layers. Numerical and statistical results obtained from this study canbe useful to select the appropriate fiber types and number of layers for laminated composite plates.
- 31 August 2022
- Published by ALKU Fen Bilimleri Dergisi, Alanya Alaaddin Keykubat University in ALKÜ Fen Bilimleri Dergisi
- Vol. 4 (2) , 63-70
Effects of Fiber Type and Number of Layers on Modal Analysis of Laminated Composite Plates
The goal of this study is to examine the effects of fiber type and number of layers on modal analysis oflaminated composite plates using finite element and Taguchi methods. Modal analysis was carried out byfinite element software ANSYS in accordance with L9 orthogonal array which has two control factors suchas fiber types and number of layers. Optimal levels of fiber types and number of layers were determinedusing analysis of Signal-to-Noise ratio, while importance levels and percentage effects of control factorswere performed using analysis of variance at 95% confidence level. According to results obtained from thisstudy, the maximum fundamental natural frequency value was calculated using boron-fiber-reinforcedlaminated composite plates with three layers. Numerical and statistical results obtained from this study canbe useful to select the appropriate fiber types and number of layers for laminated composite plates.
- 1 October 2017
- Published by Sakarya University Journal of Science in Sakarya University Journal of Science
- Vol. 21 (5) , 1
Eksenel yönde tabakalı kirişlerin temel frekansı üzerinde tabaka sıralamalarının etkileri
- 1 October 2017
- Published by Sakarya University Journal of Science in Sakarya University Journal of Science
- Vol. 21 (5) , 1
Eksenel yönde tabakalı kirişlerin temel frekansı üzerinde tabaka sıralamalarının etkileri
- 25 September 2016
- Published by Techno-Press in STRUCTURAL ENGINEERING AND MECHANICS
- Vol. 59 (6) , 1055-1070
Free vibration and buckling analysis of the impacted hybrid composite beams
- 25 September 2016
- Published by Techno-Press in STRUCTURAL ENGINEERING AND MECHANICS
- Vol. 59 (6) , 1055-1070
Free vibration and buckling analysis of the impacted hybrid composite beams
- Open Access
- 19 December 2014
- Published by Walter de Gruyter GmbH in Science and Engineering of Composite Materials
- Vol. 23 (4) , 453-460
Free vibration analysis of axially layered functionally graded short beams using experimental and finite element methods
Free vibration behavior of short beams made of axially layered functionally graded material (FGM) was investigated experimentally and numerically. Beams, which have gradation of the material properties in the axial direction, are fabricated by powder metallurgy technique using different weight fractions of aluminum and silicon carbide powders. In order to determine elasticity modulus of axially layered functionally graded (FG) beams, homogeneous beams containing different weight fractions of Al (aluminum) and SiC (silicon carbide) are produced, and these homogeneous beams are subjected to tensile tests. Density of each homogeneous layer is also calculated experimentally. After determination of the mechanical properties of each layer of the FG beams, they are modeled in a finite element program (ANSYS) according to Timoshenko beam theory, and free vibration analyses are performed. Fundamental frequencies of the axially layered FG beams produced are also calculated experimentally. FG beams with clamped-free boundary conditions are considered. Layers of the axially FG beams are considered to have symmetric configurations. Effect of the change in weight fractions of SiC particles and sorting order of layers to fundamental frequency of the beam is investigated. Experimental results obtained are compared with numerical results.
- 19 December 2014
- Published by Walter de Gruyter GmbH in Science and Engineering of Composite Materials
- Vol. 23 (4) , 453-460
Open AccessFree vibration analysis of axially layered functionally graded short beams using experimental and finite element methods
Free vibration behavior of short beams made of axially layered functionally graded material (FGM) was investigated experimentally and numerically. Beams, which have gradation of the material properties in the axial direction, are fabricated by powder metallurgy technique using different weight fractions of aluminum and silicon carbide powders. In order to determine elasticity modulus of axially layered functionally graded (FG) beams, homogeneous beams containing different weight fractions of Al (aluminum) and SiC (silicon carbide) are produced, and these homogeneous beams are subjected to tensile tests. Density of each homogeneous layer is also calculated experimentally. After determination of the mechanical properties of each layer of the FG beams, they are modeled in a finite element program (ANSYS) according to Timoshenko beam theory, and free vibration analyses are performed. Fundamental frequencies of the axially layered FG beams produced are also calculated experimentally. FG beams with clamped-free boundary conditions are considered. Layers of the axially FG beams are considered to have symmetric configurations. Effect of the change in weight fractions of SiC particles and sorting order of layers to fundamental frequency of the beam is investigated. Experimental results obtained are compared with numerical results.
- 2 June 2014
- Published by ASME International in Journal of Vibration and Acoustics
- Vol. 136 (4) , 041018
An Investigation of the Effect of Weatherstrip Seals on Vehicle Vibration and Acoustics Using an Alternative Modeling Technique
In this study, the effect of weatherstrip seals on panel vibrations and structure borne noise is studied. First, a test structure is built to model vehicle's body and door; hammer impact tests are carried out to determine frequency shifts in door vibration modes with the inclusion of rubber seals. Then, a finite element model of the test structure is built. Rubber seals are modeled as spring elements, and a modal analysis is carried out. Finite element results are compared to experimental ones to check the validity of the model used. Following a parametric study to determine stiffness of linear springs, the full vehicle is modeled using finite elements, and the effect of rubber weatherstrip seals on sound pressure level (SPL) inside the passenger compartment is studied. Frequency response curves are plotted.
- 2 June 2014
- Published by ASME International in Journal of Vibration and Acoustics
- Vol. 136 (4) , 041018
An Investigation of the Effect of Weatherstrip Seals on Vehicle Vibration and Acoustics Using an Alternative Modeling Technique
In this study, the effect of weatherstrip seals on panel vibrations and structure borne noise is studied. First, a test structure is built to model vehicle's body and door; hammer impact tests are carried out to determine frequency shifts in door vibration modes with the inclusion of rubber seals. Then, a finite element model of the test structure is built. Rubber seals are modeled as spring elements, and a modal analysis is carried out. Finite element results are compared to experimental ones to check the validity of the model used. Following a parametric study to determine stiffness of linear springs, the full vehicle is modeled using finite elements, and the effect of rubber weatherstrip seals on sound pressure level (SPL) inside the passenger compartment is studied. Frequency response curves are plotted.
- 1 April 2014
- Published by Elsevier in Applied Mathematics and Computation
- Vol. 232, 1037-1045
A Combining Method for solution of nonlinear boundary value problems
- 1 April 2014
- Published by Elsevier in Applied Mathematics and Computation
- Vol. 232, 1037-1045
A Combining Method for solution of nonlinear boundary value problems
- Open Access
- 1 December 2013
- Published by MDPI AG in Mathematical and Computational Applications
- Vol. 18 (3) , 351-360
Vibration Analysis of Functionally Graded Sandwich Beam with Variable Cross-Section
In this study, free vibration behavior of a multilayered symmetric sandwich beam made of Functionally Graded Material (FGM) with variable cross-section is investigated. The elasticity and density of the Functionally Graded (FG) sandwich beam vary through the thickness according to the power and exponential laws by using mixture rules and laminate theory. In order to provide this, fifty layered beam is considered. Each layer is isotropic and homogeneous although the volume fractions of the constituents of the layers are different. Furthermore, the width of the beam varies exponentially along the length of the beam with rectangular cross-section. The natural frequencies are computed for conventional boundary conditions of the FG sandwich beam using theoretical procedure. The effects of material index, geometric index and slenderness ratio are also discussed. Finally, the obtained results are compared with those in literature and a finite element based commercial program ANSYS® and found to be consistent with each other.
- 1 December 2013
- Published by MDPI AG in Mathematical and Computational Applications
- Vol. 18 (3) , 351-360
Open AccessVibration Analysis of Functionally Graded Sandwich Beam with Variable Cross-Section
In this study, free vibration behavior of a multilayered symmetric sandwich beam made of Functionally Graded Material (FGM) with variable cross-section is investigated. The elasticity and density of the Functionally Graded (FG) sandwich beam vary through the thickness according to the power and exponential laws by using mixture rules and laminate theory. In order to provide this, fifty layered beam is considered. Each layer is isotropic and homogeneous although the volume fractions of the constituents of the layers are different. Furthermore, the width of the beam varies exponentially along the length of the beam with rectangular cross-section. The natural frequencies are computed for conventional boundary conditions of the FG sandwich beam using theoretical procedure. The effects of material index, geometric index and slenderness ratio are also discussed. Finally, the obtained results are compared with those in literature and a finite element based commercial program ANSYS® and found to be consistent with each other.
- Open Access
- 14 September 2013
- Published by Walter de Gruyter GmbH in Science and Engineering of Composite Materials
- Vol. 21 (3) , 453-461
Vibration behavior of a radially functionally graded annular disc with variable geometry
In this study, the free vibration behavior of an annular disc made of functionally graded material (FGM) with variable geometry is investigated. The elasticity modulus, density, and thickness of the disc are assumed to vary through the radial direction according to the power law so that the effects of their indexes on the natural frequency of the disc are investigated. The Poisson’s ratio is assumed as a constant. The natural frequencies of the disc are calculated for various boundary conditions by using classical plate theory, and the various types of mode shapes, which are described by the number of nodal diameters and nodal circles, are also discussed. Moreover, the effects of the ratio of the inner radius to the outer radius on the natural frequency are also considered. It is found that in order to increase the natural frequency, the elasticity modulus and thickness should be increased at the inner surface, whereas density should be increased at the outer surface. The natural frequency can also be increased by increasing the ratio of inner radius to outer radius. The results obtained are compared with the results of a finite-element-based commercial program, ANSYS ® , and found to be consistent with each other.
- 14 September 2013
- Published by Walter de Gruyter GmbH in Science and Engineering of Composite Materials
- Vol. 21 (3) , 453-461
Open AccessVibration behavior of a radially functionally graded annular disc with variable geometry
In this study, the free vibration behavior of an annular disc made of functionally graded material (FGM) with variable geometry is investigated. The elasticity modulus, density, and thickness of the disc are assumed to vary through the radial direction according to the power law so that the effects of their indexes on the natural frequency of the disc are investigated. The Poisson’s ratio is assumed as a constant. The natural frequencies of the disc are calculated for various boundary conditions by using classical plate theory, and the various types of mode shapes, which are described by the number of nodal diameters and nodal circles, are also discussed. Moreover, the effects of the ratio of the inner radius to the outer radius on the natural frequency are also considered. It is found that in order to increase the natural frequency, the elasticity modulus and thickness should be increased at the inner surface, whereas density should be increased at the outer surface. The natural frequency can also be increased by increasing the ratio of inner radius to outer radius. The results obtained are compared with the results of a finite-element-based commercial program, ANSYS ® , and found to be consistent with each other.
- Open Access
- 1 January 2013
- Published by Wiley in Mathematical Problems in Engineering
- Vol. 2013, 1-12
Buckling Analyses of Axially Functionally Graded Nonuniform Columns with Elastic Restraint Using a Localized Differential Quadrature Method
A localized differential quadrature method (LDQM) is introduced for buckling analysis of axially functionally graded nonuniform columns with elastic restraints. Weighting coefficients of differential quadrature discretization are obtained making use of neighboring points in forward and backward type schemes for the reference grids near the beginning and end boundaries of the physical domain, respectively, and central type scheme for the reference grids inside the physical domain. Boundary conditions are directly implemented into weighting coefficient matrices, and there is no need to use fictitious points near the boundaries. Compatibility equations are not required because the governing differential equation is discretized only once for each reference grid using neighboring points and variation of flexural rigidity is taken to be continuous in the axial direction. A large case of columns having different variations of cross-sectional profile and modulus of elasticity in the axial direction are considered. The results for nondimensional critical buckling loads are compared to the analytical and numerical results available in the literature. Some new results are also given. Comparison of the results shows the potential of the LDQM for solving such generalized eigenvalue problems governed by fourth-order variable coefficient differential equations with high accuracy and less computational effort.
- 1 January 2013
- Published by Wiley in Mathematical Problems in Engineering
- Vol. 2013, 1-12
Open AccessBuckling Analyses of Axially Functionally Graded Nonuniform Columns with Elastic Restraint Using a Localized Differential Quadrature Method
A localized differential quadrature method (LDQM) is introduced for buckling analysis of axially functionally graded nonuniform columns with elastic restraints. Weighting coefficients of differential quadrature discretization are obtained making use of neighboring points in forward and backward type schemes for the reference grids near the beginning and end boundaries of the physical domain, respectively, and central type scheme for the reference grids inside the physical domain. Boundary conditions are directly implemented into weighting coefficient matrices, and there is no need to use fictitious points near the boundaries. Compatibility equations are not required because the governing differential equation is discretized only once for each reference grid using neighboring points and variation of flexural rigidity is taken to be continuous in the axial direction. A large case of columns having different variations of cross-sectional profile and modulus of elasticity in the axial direction are considered. The results for nondimensional critical buckling loads are compared to the analytical and numerical results available in the literature. Some new results are also given. Comparison of the results shows the potential of the LDQM for solving such generalized eigenvalue problems governed by fourth-order variable coefficient differential equations with high accuracy and less computational effort.