EDErsin Demir

Ersin Demir

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Ersin Demir has a total of 14 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Lateral Torsional and Longitudinal Buckling Analysis of Perforated Composite Plates

    by Ersin Demir

    In this study, lateral and longitudinal buckling behaviors of perforated composite plates are investigated numerically. The composite plates are assumed to consist of two types of fabric, unidirectional and woven fabrics. The effects of changing the location, diameter and number of holes in the plate for unidirectional and woven fabric types on the lateral and longitudinal buckling strength are compared between the unperforated plate and each other. In addition, the effects of changing the fiber orientation angle on the lateral and longitudinal buckling load of the unidirectional fabric are also examined. Finally, the changes in the mode shape in two planes in lateral buckling and in a single plane in longitudinal buckling are shown, and the normalized amplitude change in the upper point of the free end of the plate is analyzed for different hole cases. In this study, the SolidWorks program is used for model design and the Simulation module of the SolidWorks program is used for numerical analysis.

  • Open Access

    Large Deflection Analysis of Functionally Graded Beam by Using Combining Method

    by Ersin Demir, Hasan Çallıoğlu, Zekeriya Girgin

    In this study, the large deflection behavior of a circular cross-section beam is examined using the Combining Method (CM). The CM is a numerical solution method that uses block diagrams in the Matlab-Simulink program and weighting coefficients in the Differential Quadrature Method (DQM). The beam material considered is Functionally Graded Material (FGM). Boundary conditions of the beam are taken as clamped-free (C-F) and a singular load is assumed to be applied from the free end of the beam. Geometric nonlinear analysis is performed while calculating the large deflection equations of the beam and performing numerical analysis. The effects of increasing the force applied to the beam, changing the beam cross-section in the longitudinal direction, and changing the material index of the FGM on the extreme deflection behavior of the beam were examined. For comparison purposes, the results obtained from CM are compared with the results obtained from both SolidWorks-Simulation and Ansys-Workbench programs. As a result of the analysis, increasing the applied force causes the x and y coordinates of the end point of the beam to decrease. The change in geometry and material index greatly affects the large deflection occurring in the beam.


  • Open Access

    A Numerical Study on the Large Displacement in Functionally Graded Beam under Thermal Effect

    by Ersin Demi̇r

    The large displacement behavior of a Functionally Graded (FG) beam under uniform thermal load is investigated numerically. Six different effects are taken into consideration when examining the large displacement behavior of the beam. These are the effects of temperature, material, geometry, slenderness, force, and boundary condition. The nonlinear numerical analysis is carried out by using the Simulation mode of SolidWorks, which is a finite element-based commercial program. As a result, the displacement of the end of the beam increase with increasing temperature, slenderness ratio, and force. However, it decreases with increase in the ratio of ceramic in Functionally Graded Material (FGM) and the width of the beam. Moreover, as expected, the maximum and minimum displacements are obtained in the beams with Clamped-Free and Clamped-Clamped boundary conditions, respectively.


  • Open Access

    Experimental Study on Large Deflections of Perforated Composite Plates

    by Ersin Demir

    An experimental investigation on the large deflection of perforated composite plates is performed in this study. The fabrics of the composite plates are considered as unidirectional and woven. The effects of the variations in diameter, number and location of hole on plates are examined. The effects of the fabrics are also examined. One short edge of the composite plate is clamped, and a constant weight is hanged from the other short edge of the composite plate during the experiments. In order to prove the accuracy of the study done in the experiment, the large deflection analysis of the perforated plates is also made by the SolidWorks simulation program. SolidWorks simulation program is capable of performing large deflection analysis based on finite elements. When the results are examined, the large deflection is less in the woven type fabric and the large deflection value in the multi-hole specimens is higher than the single-hole ones. It is also determined that the increase in the distance of the hole position from the clamped end of the plate reduces the large deflection. As a result of the comparison of linear and nonlinear calculations, it is seen that non-linear calculation should be preferred especially if the applied force is large. When the experimental and the numerical results are compared, it is seen that the obtained results are compatible.

  • An approach for predicting longitudinal free vibration of axially functionally graded bar by artificial neural network

    by Ersin Demir, Metin Sayer, Hasan Callioglu

    In this study, an Artificial Neural Network (ANN) model is designed for the analysis of the longitudinal free vibration of an axially Functional Graded (FG) bar. The material of the bar is varied from one end to the other end according to power law function. Aluminum and Alumina and the mixture of these two materials are used in the analysis. The radius of the bar is also varied along to the longitudinal direction according to power law function. In addition, the effect of the variation in the slenderness ratio is also investigated. An ANN code is written in Matlab in order to obtain a generalized approach for vibration analysis of the FG bar. In the ANN training, some results of free vibration analysis obtained from the SolidWorks program based on Finite Element Method are used. The predicted values that are not used in the training are also obtained in SolidWorks for comparison. A Matlab program code, which based ANN method is used to find new values to be predicted. The process is also made for comparison with the ANN based Matlab nntool program. When the results obtained from SolidWorks and prepared Matlab code and Matlab nntool are compared, it is seen that the results are in harmony. AMS subject classifications: 74H45, 68T07


  • Impact behaviors of composite plates filled with chitosan/carbon nanotubes

    by Hasan Callioglu, Metin Sayer, Ersin Demir

    In this study, the effects of chitosan (1%, 2%, and 3%), multi-walled carbon nanotubes (0.1%, 0.2%, and 0.3%), and chitosan-carbon nanotube hybrid (1%, 2%, and 3% chitosan + 0.3% carbon nanotube) additions at different rates on the impact behaviors and the damage mechanisms of the E-glass/epoxy composite plates were investigated experimentally. The low-velocity drop impact testing was applied to the composite plates under different impact energies. The impact energy varied between 5 J and 30 J and it was possible to examine the impact response and the damage mechanism until the starting of the penetration of the composite plates. The experimental results revealed that the absorbed impact energies in chitosan and chitosan + carbon nanotube-filled composite plates were slightly higher than those in carbon nanotube-filled composite plates. The best energy absorption performances were obtained in chitosan + carbon nanotube hybrid filled composite plates when compared to all other composite plates and the neat composite plate. A certain amount of improvement in the impact strengths of the filled composite plates was observed when compared to neat composite plate. By increasing the impact energy, the fibers on the front surface were increasingly separated from the surface in an elliptical form, and the matrix cracking and the fiber breakages occurred throughout a line on the back surface.


  • A compact motion controller-based planar motion mechanism for captive manoeuvring tests

    by M. Cansın Özden, Sertaç Kurdoğlu, Ersin Demir, Kadir Sarıöz, Ömer Gören


  • Longitudinal Vibration of Temperature Dependent Bar with Variable Cross-Section

    by Ersin Demir

    Vibration behavior of a bar with variable cross-section, which its material properties vary with temperature, is investigated in this study. In the analysis, not only theoretical solution but also numerical solution is performed for validation. The numerical analysis is overcome by SolidWorks program based on finite element method. Four types of effects on the bar are investigated. These are effects of temperature variation, geometric ratio, slenderness ratio and mode numbers variation. The temperature is increased from 22 degrees C to 250 degrees C. The geometric ratio is varied from 0 to -1/L at intervals of 0.25/L. The slenderness ratio is varied from 1/10 to 1/20 by increasing the length of bar from 200 mm to 400 mm. As for the mode numbers, the first three mode shapes are examined in the analysis. The boundary condition of the bar is taken as clamped-free. According to the results, the natural frequency decreases with increasing the temperature. The natural frequency also decreases with decreasing the slenderness ratio. But, it increases with decreasing the geometric ratio and also increases with increasing the mode number. When the theoretical and numerical results are examined, it is seen that the results are in harmony.