Farid U. Enikeev
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Farid U. Enikeev has a total of 70 co-authors. Here are the top co-authors by number of shared publications:
- Aleksey Kruglov
Russian Academy of Sciences
10 shared publications M. I. Mazurski
Institute for Metals Superplasticity Problems
4 shared publicationsO. P. Tulupova
Ufa State Petroleum Technical University
4 shared publicationsM.I. Mazurski
Institute for Metals Superplasticity Problems, Academy of Sciences of Russia, Khalturina, 39, Ufa, 45001, Russia
3 shared publicationsR. A. Vasin
Institute for Metals Superplasticity Problems
3 shared publicationsR.A. Vasin
3 shared publications
Latest Publications
- Open Access
- 7 September 2026
- Published by Financial University under the Government of the Russian Federation in Digital Solutions and Artificial Intelligence Technologies
- Vol. 2 (3) , 41-50
Data engineering and machine learning for solving the inverse problem based on CAE simulation results
The use of machine learning in solving direct forecasting problems is becoming an alternative to the use of comprehensive finite element modeling. However, the solutions of inverse problem by means of machine learning is conventionally not considered in the literature. Traditional approaches are based on iterative calculations that require multiple runs of models and do not work in real time, which limits the creation of digital doubles. The objective of this study is to solve the inverse problem by developing and verifying a Gaussian regression (GPR) model for determining the strain rate sensitivity index of superplastic material from the results of bulge tests based on the results of finite element calculations. The results of finite element modeling of the superplastic forming process in the ANSYS CAE package were used as a data source. 120 finite element simulations were performed, 40 for each of the three pressure modes. Two GPR models have been developed. One is for defining K with the Matern kernel, the second is for m with the RBF kernel. It is shown that replacing the RBF kernel with the Matern kernel (ν = 2,5) reduces the median relative uncertainty of the forecast for parameter K from 50 to 16%. The following quality metrics were obtained on the test sample: R 2 = 0.91 for K and R 2 = 0.92 for m , the relative RMS error is 20% for K and 7% for m . The developed model can be used for non-destructive quality control, integration into digital twins, and optimization of superplastic forming processes.
- 7 September 2026
- Published by Financial University under the Government of the Russian Federation in Digital Solutions and Artificial Intelligence Technologies
- Vol. 2 (3) , 41-50
Open AccessData engineering and machine learning for solving the inverse problem based on CAE simulation results
The use of machine learning in solving direct forecasting problems is becoming an alternative to the use of comprehensive finite element modeling. However, the solutions of inverse problem by means of machine learning is conventionally not considered in the literature. Traditional approaches are based on iterative calculations that require multiple runs of models and do not work in real time, which limits the creation of digital doubles. The objective of this study is to solve the inverse problem by developing and verifying a Gaussian regression (GPR) model for determining the strain rate sensitivity index of superplastic material from the results of bulge tests based on the results of finite element calculations. The results of finite element modeling of the superplastic forming process in the ANSYS CAE package were used as a data source. 120 finite element simulations were performed, 40 for each of the three pressure modes. Two GPR models have been developed. One is for defining K with the Matern kernel, the second is for m with the RBF kernel. It is shown that replacing the RBF kernel with the Matern kernel (ν = 2,5) reduces the median relative uncertainty of the forecast for parameter K from 50 to 16%. The following quality metrics were obtained on the test sample: R 2 = 0.91 for K and R 2 = 0.92 for m , the relative RMS error is 20% for K and 7% for m . The developed model can be used for non-destructive quality control, integration into digital twins, and optimization of superplastic forming processes.
- 1 June 2022
- Published by Institute for Metals Superplasticity Problems of RAS in Letters on Materials
- Vol. 12 (2) , 142-147
Improving the accuracy of finite element modeling of superplastic forming processes
A method of improving the accuracy of finite element modeling of superplastic forming processes is suggested.
- 1 June 2022
- Published by Institute for Metals Superplasticity Problems of RAS in Letters on Materials
- Vol. 12 (2) , 142-147
Improving the accuracy of finite element modeling of superplastic forming processes
A method of improving the accuracy of finite element modeling of superplastic forming processes is suggested.
- 1 January 2019
- Published by Institute for Metals Superplasticity Problems of RAS in Letters on Materials
- Vol. 9 (4) , 433-435
Influence of the inclination angle of stiffeners on folding during superplastic forming of corrugated core panels
Superplastic forming of thin sheet corrugated structures is of special interest in developing aircraft technologies of new generation.
- 1 January 2019
- Published by Institute for Metals Superplasticity Problems of RAS in Letters on Materials
- Vol. 9 (4) , 433-435
Influence of the inclination angle of stiffeners on folding during superplastic forming of corrugated core panels
Superplastic forming of thin sheet corrugated structures is of special interest in developing aircraft technologies of new generation.
- 26 December 2018
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 941, 2343-2348
On the Challenges and Prospects of the Superplastic Forming Process
Superplastic forming has already been proven as a practical solution for manufacturing lightweight components in niche applications such as the aerospace and luxury cars industries. The demand to produce such components will continue with the limited nature of the energy resources available today. Therefore, superplastic materials are expected to stay as potential candidates in such applications. In addition, superplastic forming offers many unique advantages over conventional forming techniques including greater design flexibility, relatively low tooling cost, and no spring back. However, the full potential of the process has not yet been fulfilled due to concerns about the nonuniformity of the produced parts thickness profiles and the need for heating to achieve the superplastic properties of the material. In this paper the authors address the main challenges that hinder the wide spread of the process. It is of great practical importance, for example, to develop accurate simulations of the superplastic forming process. Such simulations are required for identifying the optimum process parameters for high quality components. The results of any such simulations or experimental investigations should be translated into simple and clear industrial guidelines. In addition, they discuss the current trends and the prospects of this process.
- 26 December 2018
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 941, 2343-2348
On the Challenges and Prospects of the Superplastic Forming Process
Superplastic forming has already been proven as a practical solution for manufacturing lightweight components in niche applications such as the aerospace and luxury cars industries. The demand to produce such components will continue with the limited nature of the energy resources available today. Therefore, superplastic materials are expected to stay as potential candidates in such applications. In addition, superplastic forming offers many unique advantages over conventional forming techniques including greater design flexibility, relatively low tooling cost, and no spring back. However, the full potential of the process has not yet been fulfilled due to concerns about the nonuniformity of the produced parts thickness profiles and the need for heating to achieve the superplastic properties of the material. In this paper the authors address the main challenges that hinder the wide spread of the process. It is of great practical importance, for example, to develop accurate simulations of the superplastic forming process. Such simulations are required for identifying the optimum process parameters for high quality components. The results of any such simulations or experimental investigations should be translated into simple and clear industrial guidelines. In addition, they discuss the current trends and the prospects of this process.
- Open Access
- 21 November 2018
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 447 (1) , 012039
Improving the accuracy of finite element modeling of superplastic hemisphere forming
A novel procedure to determine the values of the material constants K and m for the standard power superplastic law from the results of the bulge tests of the hemispheres is suggested. Unlike other approaches known in the literature.the involved procedure requires only two experimental measurements of the time of formingunder constant pressure, with the thickness at the pole being used to refine the values K and m. Experimental justificationof the developed techniques wasfulfilled on the example of aluminum alloyAA5083. The validity of the suggested approach is confirmed by comparing the experimental data with the corresponding finite element solutions of the boundary value problem in the theory of creep productionusing the ANSYS software. It is found that the maximum deviation of experimental records from the corresponding finite element solutions does not exceed 1% both for the time of formation and for the thickness at the pole.
- 21 November 2018
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 447 (1) , 012039
Open AccessImproving the accuracy of finite element modeling of superplastic hemisphere forming
A novel procedure to determine the values of the material constants K and m for the standard power superplastic law from the results of the bulge tests of the hemispheres is suggested. Unlike other approaches known in the literature.the involved procedure requires only two experimental measurements of the time of formingunder constant pressure, with the thickness at the pole being used to refine the values K and m. Experimental justificationof the developed techniques wasfulfilled on the example of aluminum alloyAA5083. The validity of the suggested approach is confirmed by comparing the experimental data with the corresponding finite element solutions of the boundary value problem in the theory of creep productionusing the ANSYS software. It is found that the maximum deviation of experimental records from the corresponding finite element solutions does not exceed 1% both for the time of formation and for the thickness at the pole.
- Open Access
- 21 November 2018
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 447 (1) , 012050
Computer simulation of superplastic forming of a three-sheet structure containing an ultrafine-grained core
Superplastic forming of a three-sheet structure is considered. The focus is on overcoming the main disadvantages of the process of manufacturing of such structures by means of the SPF/DB technique including high temperatures of treatment and the formation of folds on the outer surface of the article manufactured. The application of ultrafine-grained sheets of titanium alloy Ti-6Al-4V has been analyzed in order to avoid these disadvantages. Various combinations of the use of ultrafine-grained and microcrystalline sheets as skin and core sheets are considered by means of the finite element analysis. The standard power law of superplasticity is used for analysis with material constants determined from technological experiments. The conclusion is made that the most attractive way appears to be the usage of ultafine-grained material for the core sheet and microcrystalline material for the skin sheets.
- 21 November 2018
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 447 (1) , 012050
Open AccessComputer simulation of superplastic forming of a three-sheet structure containing an ultrafine-grained core
Superplastic forming of a three-sheet structure is considered. The focus is on overcoming the main disadvantages of the process of manufacturing of such structures by means of the SPF/DB technique including high temperatures of treatment and the formation of folds on the outer surface of the article manufactured. The application of ultrafine-grained sheets of titanium alloy Ti-6Al-4V has been analyzed in order to avoid these disadvantages. Various combinations of the use of ultrafine-grained and microcrystalline sheets as skin and core sheets are considered by means of the finite element analysis. The standard power law of superplasticity is used for analysis with material constants determined from technological experiments. The conclusion is made that the most attractive way appears to be the usage of ultafine-grained material for the core sheet and microcrystalline material for the skin sheets.
- 1 March 2018
- Published by Allerton Press in Mechanics of Solids
- Vol. 53 (2) , 138-146
Identification of Phenomenological Superplasticity Models Based on the Results of Technological Experiments
A general scheme for identifying the constitutive equations of superplasticity, according to which the values of material constants are calculated by the results of technological experiments using...
- 1 March 2018
- Published by Allerton Press in Mechanics of Solids
- Vol. 53 (2) , 138-146
Identification of Phenomenological Superplasticity Models Based on the Results of Technological Experiments
A general scheme for identifying the constitutive equations of superplasticity, according to which the values of material constants are calculated by the results of technological experiments using...
- 1 January 2018
- Published by Institute for Metals Superplasticity Problems of RAS in Letters on Materials
- Vol. 8 (2) , 174-177
Finite element modeling of folding during the superplastic forming of corrugated core panels
Corrugated core panels manufactured by methods of superplastic forming concurrent with diffusion bonding (SPF/DB) are promising for the production of high specific strength articles. One of serious problems arising in forming of corrugated core panels is concerned with the formation of the outer folds. The cause of folding is the uneven deformation of the skin sheets. In this study, the process of forming a corrugated core panel from a titanium alloy VT6 (analogue of Ti-6Al-4V) by computer simulation is considered. Finite element modeling is carrying out using ANSYS software. The formulation of the boundary value problem is stated in terms of the theory of creep. It is shown that after completion of the formation of stiffening ribs, it is possible to increase the working pressure to a maximum without damaging the structure. The results of numerical simulation showed that increasing the amount of pressure and holding time helps to eliminate folds. However, the pressure value is technically limited, and increasing the holding time reduces the economic efficiency of the process. It is noted that the process of forming a corrugated core panel has two characteristic stages. In the first stage, the core sheet is deformed under the conditions of superplasticity, stiffening ribs are formed. The first stage continues until the skin sections joined to the core touches the surface of the die. The second stage proceeds under conditions of creep up to smoothing the outer folds.
- 1 January 2018
- Published by Institute for Metals Superplasticity Problems of RAS in Letters on Materials
- Vol. 8 (2) , 174-177
Finite element modeling of folding during the superplastic forming of corrugated core panels
Corrugated core panels manufactured by methods of superplastic forming concurrent with diffusion bonding (SPF/DB) are promising for the production of high specific strength articles. One of serious problems arising in forming of corrugated core panels is concerned with the formation of the outer folds. The cause of folding is the uneven deformation of the skin sheets. In this study, the process of forming a corrugated core panel from a titanium alloy VT6 (analogue of Ti-6Al-4V) by computer simulation is considered. Finite element modeling is carrying out using ANSYS software. The formulation of the boundary value problem is stated in terms of the theory of creep. It is shown that after completion of the formation of stiffening ribs, it is possible to increase the working pressure to a maximum without damaging the structure. The results of numerical simulation showed that increasing the amount of pressure and holding time helps to eliminate folds. However, the pressure value is technically limited, and increasing the holding time reduces the economic efficiency of the process. It is noted that the process of forming a corrugated core panel has two characteristic stages. In the first stage, the core sheet is deformed under the conditions of superplasticity, stiffening ribs are formed. The first stage continues until the skin sections joined to the core touches the surface of the die. The second stage proceeds under conditions of creep up to smoothing the outer folds.
- 1 October 2017
- Published by Elsevier in Advances in Engineering Software
- Vol. 112, 54-65
Determination of superplastic properties from the results of technological experiments
- 1 October 2017
- Published by Elsevier in Advances in Engineering Software
- Vol. 112, 54-65
Determination of superplastic properties from the results of technological experiments
- 1 May 2017
- Published by Allerton Press in Russian Journal of Non-Ferrous Metals
- Vol. 58 (3) , 250-257
Computational methods of the superplastic forming duration of a round membrane
The methods for calculating the duration of the superplastic forming of a circular membrane are considered. The results of calculations by analytical formulas are compared with the solution of boundary-value problems of the theory of creep and viscoplasticity found in the medium of the ANSYS software complex. The values of material constants were determined by the data of uniaxial tests and testing formings of the VT6 titanium alloy (Ti–6Al–4V).
- 1 May 2017
- Published by Allerton Press in Russian Journal of Non-Ferrous Metals
- Vol. 58 (3) , 250-257
Computational methods of the superplastic forming duration of a round membrane
The methods for calculating the duration of the superplastic forming of a circular membrane are considered. The results of calculations by analytical formulas are compared with the solution of boundary-value problems of the theory of creep and viscoplasticity found in the medium of the ANSYS software complex. The values of material constants were determined by the data of uniaxial tests and testing formings of the VT6 titanium alloy (Ti–6Al–4V).