Maximilian Nitzsche
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Maximilian Nitzsche has a total of 32 co-authors. Here are the top co-authors by number of shared publications:
Jorg Roth-Stielow
Institute for Power Electronics and Electrical Drives
6 shared publications- Johannes Ruthardt
Institute for Power Electronics and Electrical Drives, University of Stuttgart, Stuttgart, Germany
4 shared publications Julian Wolfle
Institute for Power Electronics and Electrical Drives, University of Stuttgart, Germany
4 shared publicationsJ. Roth-Stielow
Institute for Power Electronics and Electrical Drives, University of Stuttgart, Germany
3 shared publications- Manuel Fischer
Institute for Power Electronics and Electrical Drives, University of Stuttgart, Stuttgart, Germany
3 shared publications Martin Stempfle
Institute for Power Electronics and Electrical Drives, University of Stuttgart, Germany
3 shared publications
Latest Publications
- Open Access
- 21 December 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Open Journal of Power Electronics
- Vol. 3, 13-25
Miniaturization and Thermal Design of a 170 W AC/DC Battery Charger Utilizing GaN Power Devices
This paper presents the design and analysis of a high-density two-stage battery charger for mid-power applications like small electric vehicles and high-performance laptops utilizing gallium nitride (GaN) power devices. In addition to adherence of maximum junction temperatures, a thermal analysis is carried out for in-housing operation, which is particularly critical for fanless wall chargers. Design measures include calorimetric semiconductor selection, half-bridge miniaturization, thermally conductive epoxy resin and reference-based convection modeling for thermally optimized component placement using 3D-stacking. Furthermore, the remaining optimization potential of the charger is estimated by virtual prototyping. A 170 W hardware prototype is developed and tested, achieving a two-stage power section efficiency of 95.4 % with a maximum switching frequency of 550 kHz. This results in a power density in open-housing operation of 1.6 kW / dm. Using epoxy resin, copper and graphite heat spreaders, an in-housing operation power density of 1.1 kW / dm is achieved with minor reduction of output power due to surface temperature constraints.
- 21 December 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Open Journal of Power Electronics
- Vol. 3, 13-25
Open AccessMiniaturization and Thermal Design of a 170 W AC/DC Battery Charger Utilizing GaN Power Devices
This paper presents the design and analysis of a high-density two-stage battery charger for mid-power applications like small electric vehicles and high-performance laptops utilizing gallium nitride (GaN) power devices. In addition to adherence of maximum junction temperatures, a thermal analysis is carried out for in-housing operation, which is particularly critical for fanless wall chargers. Design measures include calorimetric semiconductor selection, half-bridge miniaturization, thermally conductive epoxy resin and reference-based convection modeling for thermally optimized component placement using 3D-stacking. Furthermore, the remaining optimization potential of the charger is estimated by virtual prototyping. A 170 W hardware prototype is developed and tested, achieving a two-stage power section efficiency of 95.4 % with a maximum switching frequency of 550 kHz. This results in a power density in open-housing operation of 1.6 kW / dm. Using epoxy resin, copper and graphite heat spreaders, an in-housing operation power density of 1.1 kW / dm is achieved with minor reduction of output power due to surface temperature constraints.
- Open Access
- 5 August 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Open Journal of Power Electronics
- Vol. 1, 273-283
Junction Temperature Control System to Increase the Lifetime of IGBT-Power-Modules in Synchronous Motor Drives Without Affecting Torque and Speed
Load changes of electrical machines driven by inverters cause temperature swings of the semiconductor devices in IGBT modules of the inverters. These temperature swings limit the numbers of cycles to failure of the IGBTs. This paper presents a temperature control system which is paralleled to the standard torque control system. It reduces the magnitude of temperature swings of the semiconductor devices caused by load changes of an interior permanent magnet synchronous machine. The principle method is, to increase the temperature of the semiconductor devices of the IGBT-modules by creating higher power losses during low load conditions of the machine without affecting torque and speed. This reduces the magnitude of the load induced temperature swings and increases lifetime at the cost of increased power losses. Three variables have been identified that influence the power losses in inverter modules without necessarily affecting the out-put power of the permanent synchronous machine. These varia-bles are switching frequency of the inverter, length of the clamp-ing area when a discontinuous modulation is applied and the reactive component of the inverter current. The influence of each variable which regards to the losses in the IGBT-power-modules is explained and the related control methodology is described.
- 5 August 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Open Journal of Power Electronics
- Vol. 1, 273-283
Open AccessJunction Temperature Control System to Increase the Lifetime of IGBT-Power-Modules in Synchronous Motor Drives Without Affecting Torque and Speed
Load changes of electrical machines driven by inverters cause temperature swings of the semiconductor devices in IGBT modules of the inverters. These temperature swings limit the numbers of cycles to failure of the IGBTs. This paper presents a temperature control system which is paralleled to the standard torque control system. It reduces the magnitude of temperature swings of the semiconductor devices caused by load changes of an interior permanent magnet synchronous machine. The principle method is, to increase the temperature of the semiconductor devices of the IGBT-modules by creating higher power losses during low load conditions of the machine without affecting torque and speed. This reduces the magnitude of the load induced temperature swings and increases lifetime at the cost of increased power losses. Three variables have been identified that influence the power losses in inverter modules without necessarily affecting the out-put power of the permanent synchronous machine. These varia-bles are switching frequency of the inverter, length of the clamp-ing area when a discontinuous modulation is applied and the reactive component of the inverter current. The influence of each variable which regards to the losses in the IGBT-power-modules is explained and the related control methodology is described.
- 1 March 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 2955
Closed Loop Junction Temperature Control of Power Transistors for Lifetime Extension
The lifetime of power transistors significantly depends on the junction temperature swings. These temperature swings occur, for instance when the load conditions of the power electronic circuit change. In this work, a closed loop junction temperature control system is designed to increase the expected lifetime of power transistors. Therefore, the control system reduces the occurring temperature swings by influencing the power losses of the power transistor. For that, the gate driver’s supply voltage is adjusted, which affects the switching speed and the conduction characteristics. The junction temperature is measured by determination of the temperature sensitive internal gate resistance via the high-frequency gate-signalinjection method and fed back to the junction temperature controller. Both, the junction temperature measurement method and the control system are evaluated with a three-phase two-level voltage-source inverter. It is extended by a control strategy, which calculates a suitable set value for the controller in order to reduce junction temperature swings.
- 1 March 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 2955
Closed Loop Junction Temperature Control of Power Transistors for Lifetime Extension
The lifetime of power transistors significantly depends on the junction temperature swings. These temperature swings occur, for instance when the load conditions of the power electronic circuit change. In this work, a closed loop junction temperature control system is designed to increase the expected lifetime of power transistors. Therefore, the control system reduces the occurring temperature swings by influencing the power losses of the power transistor. For that, the gate driver’s supply voltage is adjusted, which affects the switching speed and the conduction characteristics. The junction temperature is measured by determination of the temperature sensitive internal gate resistance via the high-frequency gate-signalinjection method and fed back to the junction temperature controller. Both, the junction temperature measurement method and the control system are evaluated with a three-phase two-level voltage-source inverter. It is extended by a control strategy, which calculates a suitable set value for the controller in order to reduce junction temperature swings.
- Open Access
- 16 April 2019
- Published by Institution of Engineering and Technology (IET) in The Journal of Engineering
- Vol. 2019 (17) , 4143-4146
Design of a full SiC three‐phase power factor correction with an interleaved output buck converter
Active rectification of the three‐phase grid nowadays is a central task of power electronics. However, as the necessary DC bus voltages vary, DC‐DC converters are needed. This study presents the design and development of a three‐phase power factor correction with an interleaved buck converter in the output stage. The power stage switches are equipped with silicon carbide (SiC) metal‐oxide‐semiconductor field‐effect transistors. A modular setup of the half‐bridge modules as well as low inductive design of these modules is put into focus.
- 16 April 2019
- Published by Institution of Engineering and Technology (IET) in The Journal of Engineering
- Vol. 2019 (17) , 4143-4146
Open AccessDesign of a full SiC three‐phase power factor correction with an interleaved output buck converter
Active rectification of the three‐phase grid nowadays is a central task of power electronics. However, as the necessary DC bus voltages vary, DC‐DC converters are needed. This study presents the design and development of a three‐phase power factor correction with an interleaved buck converter in the output stage. The power stage switches are equipped with silicon carbide (SiC) metal‐oxide‐semiconductor field‐effect transistors. A modular setup of the half‐bridge modules as well as low inductive design of these modules is put into focus.
- Open Access
- 15 April 2019
- Published by Institution of Engineering and Technology (IET) in The Journal of Engineering
- Vol. 2019 (17) , 3789-3792
Leakage current reduction for a double‐leg boost converter by switching transition synchronisation
With wide‐bandgap transistors, the leakage current through the parasitic transistor to heat sink capacitance is increased with the operation at higher switching transition voltage slopes. This study presents a modulation synchronisation method for a double‐leg boost converter to reduce these leakage currents. Having a similar leakage current path, the transistors turn‐on transition of one leg is synchronised on the turn‐off transition of the second leg.
- 15 April 2019
- Published by Institution of Engineering and Technology (IET) in The Journal of Engineering
- Vol. 2019 (17) , 3789-3792
Open AccessLeakage current reduction for a double‐leg boost converter by switching transition synchronisation
With wide‐bandgap transistors, the leakage current through the parasitic transistor to heat sink capacitance is increased with the operation at higher switching transition voltage slopes. This study presents a modulation synchronisation method for a double‐leg boost converter to reduce these leakage currents. Having a similar leakage current path, the transistors turn‐on transition of one leg is synchronised on the turn‐off transition of the second leg.
- 1 December 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 41-47
Combination of two variables in a junction temperature control system to elongate the expected lifetime of IGBT-power-modules
In power electronic applications the expected lifetime is an important issue. This paper focuses on the elongation of the expected lifetime of IGBT-power-modules. Temperature swings caused by alternating operation conditions are the major influencing factor. The temperature swings can be reduced by increasing the power losses in low load conditions. This is realized by a model based junction temperature control system. Possible correcting variables are the variation of the switching frequency and the presetting of a current amplitude. Each correcting variable has its benefits and drawbacks. This paper presents a model based junction temperature control system which combines these two correcting variables in a beneficial manner. The functionality is demonstrated on a three phase two level inverter equipped with opened and blackened IGBT power modules feeding a PMSM The correcting variables have no negative influence on the demanded output power of the PMSM.
- 1 December 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 41-47
Combination of two variables in a junction temperature control system to elongate the expected lifetime of IGBT-power-modules
In power electronic applications the expected lifetime is an important issue. This paper focuses on the elongation of the expected lifetime of IGBT-power-modules. Temperature swings caused by alternating operation conditions are the major influencing factor. The temperature swings can be reduced by increasing the power losses in low load conditions. This is realized by a model based junction temperature control system. Possible correcting variables are the variation of the switching frequency and the presetting of a current amplitude. Each correcting variable has its benefits and drawbacks. This paper presents a model based junction temperature control system which combines these two correcting variables in a beneficial manner. The functionality is demonstrated on a three phase two level inverter equipped with opened and blackened IGBT power modules feeding a PMSM The correcting variables have no negative influence on the demanded output power of the PMSM.
- 1 May 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-6
Simple but accurate loss modelling of an IPMSM considering harmonic losses and saturation effects
For drive train efficiency optimization, an accurate but simple loss model of an interior permanent magnet synchronous machine (IPMSM) is proposed. In order to analyze different inverter topologies, switching frequencies and modulation techniques it is necessary that the loss model of the machine takes losses caused by harmonics into account. Considering harmonics and saturation effects, loss characteristics of the IPMSM are shown. Furthermore, loss calculations are opposed to test bench measurements in order to validate the loss models accuracy.
- 1 May 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-6
Simple but accurate loss modelling of an IPMSM considering harmonic losses and saturation effects
For drive train efficiency optimization, an accurate but simple loss model of an interior permanent magnet synchronous machine (IPMSM) is proposed. In order to analyze different inverter topologies, switching frequencies and modulation techniques it is necessary that the loss model of the machine takes losses caused by harmonics into account. Considering harmonics and saturation effects, loss characteristics of the IPMSM are shown. Furthermore, loss calculations are opposed to test bench measurements in order to validate the loss models accuracy.