Manuel Fischer
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Manuel Fischer has a total of 31 co-authors. Here are the top co-authors by number of shared publications:
Jorg Roth-Stielow
Institute for Power Electronics and Electrical Drives
7 shared publications- Johannes Ruthardt
Institute for Power Electronics and Electrical Drives, University of Stuttgart, Stuttgart, Germany
5 shared publications - Philipp Ziegler
Institute for Power Electronics and Electrical Drives, University of Stuttgart, Stuttgart, Germany
4 shared publications - Maximilian Nitzsche
Institute for Power Electronics and Electrical Drives, University of Stuttgart, Germany
3 shared publications J. Roth-Stielow
INSTITUTE FOR POWER ELECTRONICS AND ELECTRICAL DRIVES, University of Stuttgart 70569 Stuttgart, Germany
2 shared publicationsJörg Roth‐Stielow
Institute for Power Electronics and Electrical Drives, University of Stuttgart 70569 Stuttgart Germany
2 shared publications
Latest Publications
- 17 August 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industry Applications
- Vol. 59 (6) , 7052-7060
Compact Design of a Wide Bandwidth High Current Sensor Using Tilted Magnetic Field Sensors
Magnetic field-based current sensors are widely used due to their galvanically insulated measurement principle. A well-proven concept is based on the discrete realization of Ampèere's law using a circular array of magnetic field sensors. Depending on the linear operating range of the magnetic field sensors, the radius of the circular array has to be chosen, leading to large dimensions for high current values. This paper presents a novel approach to build a compact wide bandwidth current sensor based on the combination of tilted tunnel-magnetoresistance sensors and a Rogowski coil. The used tunnel-magnetoresistance sensors are characterized and show an increased linear range in the current sensor application if they are tilted. In addition, the sensor sensitivity is varied with the tilt angle. A novel current sensor concept based on tilting in combination with repositioning the magnetic field sensors is presented. This concept offers the opportunity to reduce the size of state-of-the-art current sensors based on magnetic field sensors significantly. The proposed concept is verified in a current sensor prototype. The DC current linearity, the dynamic behavior as well as the signal-to-noise ratio is characterized. Ideas how this concept can be used and further developed are presented.
- 17 August 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industry Applications
- Vol. 59 (6) , 7052-7060
Compact Design of a Wide Bandwidth High Current Sensor Using Tilted Magnetic Field Sensors
Magnetic field-based current sensors are widely used due to their galvanically insulated measurement principle. A well-proven concept is based on the discrete realization of Ampèere's law using a circular array of magnetic field sensors. Depending on the linear operating range of the magnetic field sensors, the radius of the circular array has to be chosen, leading to large dimensions for high current values. This paper presents a novel approach to build a compact wide bandwidth current sensor based on the combination of tilted tunnel-magnetoresistance sensors and a Rogowski coil. The used tunnel-magnetoresistance sensors are characterized and show an increased linear range in the current sensor application if they are tilted. In addition, the sensor sensitivity is varied with the tilt angle. A novel current sensor concept based on tilting in combination with repositioning the magnetic field sensors is presented. This concept offers the opportunity to reduce the size of state-of-the-art current sensors based on magnetic field sensors significantly. The proposed concept is verified in a current sensor prototype. The DC current linearity, the dynamic behavior as well as the signal-to-noise ratio is characterized. Ideas how this concept can be used and further developed are presented.
- 30 November 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 31 (2) , 1-5
Analysis of Superconducting Synchronous Motors With Halbach Array Field Excitation
This paper evaluates the novel design approach of a 3 MW partially superconducting synchronous machine for electric aircraft propulsion. Its special feature is the application of an electromagnetic Halbach array for the field excitation to reduce the back yoke weight and thereby increase overall output power density. The electromagnetic Halbach array is obtained by reproducing a permanent magnet Halbach array with high-temperature superconducting coils. The arrangement is further optimized, and its field characteristics are compared to a conventional superconducting field winding design. Even though the Halbach array has a higher space and superconductor consumption, it shows better characteristics concerning the intensity of inside and outside magnetic field. Applied in a superconducting motor, the Halbach array field winding achieves a back yoke thickness reduction of up to 85% and a back yoke weight reduction of up to 78% compared to reference models. The gravimetric power density is increased by up to 30% at the expense of volumetric power density. In exchange for a back yoke weight reduction, other components, such as field winding and cryostat, become heavier.
- 30 November 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 31 (2) , 1-5
Analysis of Superconducting Synchronous Motors With Halbach Array Field Excitation
This paper evaluates the novel design approach of a 3 MW partially superconducting synchronous machine for electric aircraft propulsion. Its special feature is the application of an electromagnetic Halbach array for the field excitation to reduce the back yoke weight and thereby increase overall output power density. The electromagnetic Halbach array is obtained by reproducing a permanent magnet Halbach array with high-temperature superconducting coils. The arrangement is further optimized, and its field characteristics are compared to a conventional superconducting field winding design. Even though the Halbach array has a higher space and superconductor consumption, it shows better characteristics concerning the intensity of inside and outside magnetic field. Applied in a superconducting motor, the Halbach array field winding achieves a back yoke thickness reduction of up to 85% and a back yoke weight reduction of up to 78% compared to reference models. The gravimetric power density is increased by up to 30% at the expense of volumetric power density. In exchange for a back yoke weight reduction, other components, such as field winding and cryostat, become heavier.
- 1 March 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 2950-2954
Comparison of Two Power Electronic Topologies for Power Hardware in the Loop Machine Emulator
Emulating electrical machines simplifies development and testing inverters and their control systems in different operating conditions. Therefore, two fundamental components are required: a real-time operating machine model and an applicable power electronic device, which adjusts the same currents and voltages as the surveyed machine would. Within this paper, two different power electronic topologies are compared regarding their suitability for hardware in the loop machine emulation. The surveyed topologies are a multibranch interleaved-switched inverter on the one hand and an inverter with output filter on the other hand. Especially their dynamic behavior in emulating the machine currents’ course as precise as possible is investigated. Moreover, additional disturbances caused by the power electronics’ switched-mode operation are analyzed, too. For this purpose, both power electronic devices are set up in hardware, controlled by an exemplary machine model. This paper presents the setup of the two topologies and the dedicated control system as well as the analysis by simulation and measurement.
- 1 March 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 2950-2954
Comparison of Two Power Electronic Topologies for Power Hardware in the Loop Machine Emulator
Emulating electrical machines simplifies development and testing inverters and their control systems in different operating conditions. Therefore, two fundamental components are required: a real-time operating machine model and an applicable power electronic device, which adjusts the same currents and voltages as the surveyed machine would. Within this paper, two different power electronic topologies are compared regarding their suitability for hardware in the loop machine emulation. The surveyed topologies are a multibranch interleaved-switched inverter on the one hand and an inverter with output filter on the other hand. Especially their dynamic behavior in emulating the machine currents’ course as precise as possible is investigated. Moreover, additional disturbances caused by the power electronics’ switched-mode operation are analyzed, too. For this purpose, both power electronic devices are set up in hardware, controlled by an exemplary machine model. This paper presents the setup of the two topologies and the dedicated control system as well as the analysis by simulation and measurement.
- 1 March 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 2955
Closed Loop Junction Temperature Control of Power Transistors for Lifetime Extension
The lifetime of power transistors significantly depends on the junction temperature swings. These temperature swings occur, for instance when the load conditions of the power electronic circuit change. In this work, a closed loop junction temperature control system is designed to increase the expected lifetime of power transistors. Therefore, the control system reduces the occurring temperature swings by influencing the power losses of the power transistor. For that, the gate driver’s supply voltage is adjusted, which affects the switching speed and the conduction characteristics. The junction temperature is measured by determination of the temperature sensitive internal gate resistance via the high-frequency gate-signalinjection method and fed back to the junction temperature controller. Both, the junction temperature measurement method and the control system are evaluated with a three-phase two-level voltage-source inverter. It is extended by a control strategy, which calculates a suitable set value for the controller in order to reduce junction temperature swings.
- 1 March 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 2955
Closed Loop Junction Temperature Control of Power Transistors for Lifetime Extension
The lifetime of power transistors significantly depends on the junction temperature swings. These temperature swings occur, for instance when the load conditions of the power electronic circuit change. In this work, a closed loop junction temperature control system is designed to increase the expected lifetime of power transistors. Therefore, the control system reduces the occurring temperature swings by influencing the power losses of the power transistor. For that, the gate driver’s supply voltage is adjusted, which affects the switching speed and the conduction characteristics. The junction temperature is measured by determination of the temperature sensitive internal gate resistance via the high-frequency gate-signalinjection method and fed back to the junction temperature controller. Both, the junction temperature measurement method and the control system are evaluated with a three-phase two-level voltage-source inverter. It is extended by a control strategy, which calculates a suitable set value for the controller in order to reduce junction temperature swings.
- 1 September 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. P.1-P.8
Investigation on a Three-Phase Inverter with LC Output Filter for Machine Emulation
- 1 September 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. P.1-P.8
Investigation on a Three-Phase Inverter with LC Output Filter for Machine Emulation
- 1 September 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. P.1-P.8
Model Based Junction Temperature Control Using the Gate Driver Voltage as a Correction Variable
- 1 September 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. P.1-P.8
Model Based Junction Temperature Control Using the Gate Driver Voltage as a Correction Variable
- 1 July 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- Vol. 7, 1-7
Load Emulation for Electrolysis Rectifiers
Load emulation is a power hardware in the loop approach for testing rectifiers used for electrolysis in context of renewable energies. It enables development and testing of rectifiers without the need of a real electrolyzer with its peripherals. The demands for the application, a modular power electronic concept as well as a control system capable of fully reproducing the timing behavior of an electrolyzer, are presented. The approach is validated using a simulation model and measurements on a demonstrator circuit.
- 1 July 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- Vol. 7, 1-7
Load Emulation for Electrolysis Rectifiers
Load emulation is a power hardware in the loop approach for testing rectifiers used for electrolysis in context of renewable energies. It enables development and testing of rectifiers without the need of a real electrolyzer with its peripherals. The demands for the application, a modular power electronic concept as well as a control system capable of fully reproducing the timing behavior of an electrolyzer, are presented. The approach is validated using a simulation model and measurements on a demonstrator circuit.
- Open Access
- 15 April 2019
- Published by Institution of Engineering and Technology (IET) in The Journal of Engineering
- Vol. 2019 (17) , 3692-3695
Gate‐driver circuit with a variable supply voltage to influence the switching losses
The lifetime of semiconductor devices used in power electronics depends on the junction temperature. With a suitable junction temperature control system, the lifetime of semiconductor devices is extended. These control systems require a possibility to influence the power losses of the semiconductor devices and therefore the junction temperature. The proposed gate‐driver circuit has a variable supply voltage in order to influence the switching speed of the semiconductor devices. This affects the switching losses. In addition, the adjustable switching speed can be used to prevent voltage overshoots during the switching transition or to decrease electromagnetic emission. The main advantage of this gate‐driver circuit is its simple structure. This study focuses on the switching losses.
- 15 April 2019
- Published by Institution of Engineering and Technology (IET) in The Journal of Engineering
- Vol. 2019 (17) , 3692-3695
Open AccessGate‐driver circuit with a variable supply voltage to influence the switching losses
The lifetime of semiconductor devices used in power electronics depends on the junction temperature. With a suitable junction temperature control system, the lifetime of semiconductor devices is extended. These control systems require a possibility to influence the power losses of the semiconductor devices and therefore the junction temperature. The proposed gate‐driver circuit has a variable supply voltage in order to influence the switching speed of the semiconductor devices. This affects the switching losses. In addition, the adjustable switching speed can be used to prevent voltage overshoots during the switching transition or to decrease electromagnetic emission. The main advantage of this gate‐driver circuit is its simple structure. This study focuses on the switching losses.
- Open Access
- 15 April 2019
- Published by Institution of Engineering and Technology (IET) in The Journal of Engineering
- Vol. 2019 (17) , 4041-4044
Design of a three‐phase 100 A linear amplifier for power‐hardware‐in‐the‐loop machine emulation
Here, the setup of a three‐phase 100 A linear amplifier is proposed. This work focusses on the use of this linear amplifier as power element for machine‐emulation. In contrast to common power electronics, a linear amplifier avoids ripple content in the output current caused by switched‐mode operation.
- 15 April 2019
- Published by Institution of Engineering and Technology (IET) in The Journal of Engineering
- Vol. 2019 (17) , 4041-4044
Open AccessDesign of a three‐phase 100 A linear amplifier for power‐hardware‐in‐the‐loop machine emulation
Here, the setup of a three‐phase 100 A linear amplifier is proposed. This work focusses on the use of this linear amplifier as power element for machine‐emulation. In contrast to common power electronics, a linear amplifier avoids ripple content in the output current caused by switched‐mode operation.