Chainarong Kittiyanpunya
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Chainarong Kittiyanpunya has a total of 26 co-authors. Here are the top co-authors by number of shared publications:
Monai Krairiksh
Faculty of Engineering, King Mongkuts Institute of Technology Ladkrabang, Bangkok, Thailand
7 shared publicationsM. Krairiksh
Faculty of Engineering, King Mongkut's Institute of Technology Ladkrabang Bangkok 10520, Thailan
6 shared publications- Chuwong Phongcharoenpanich
School of Engineering, King Mongkut’s Institute of Technology Ladkrabang, Bangkok 10520, Thailand
4 shared publications - Monai Krairiksh
School of Engineering, King Mongkuts Institute of Technology Ladkrabang, Bangkok, Thailand
2 shared publications Paiboon Yoiyod
College of Engineering, Rangsit University, Pathumtani, Thailand
2 shared publications- Pongsathorn Chomdee
Institute of Metropolitan Development, Navamindradhiraj University
2 shared publications
Latest Publications
- Open Access
- 1 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 14, 136986-136996
Nondestructive Detection of Abnormally Thick Pomelo Rind via Frequency Domain Decomposition
- 1 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 14, 136986-136996
Open AccessNondestructive Detection of Abnormally Thick Pomelo Rind via Frequency Domain Decomposition
- 18 September 2023
- Published by American Geophysical Union (AGU) in Radio Science
- Vol. 58 (9)
Printed Dual‐Frequency Directional Antenna Loaded With Dual‐Parasitic Strip
In this paper, the directional antenna is developed to construct the printed dual‐frequency directional antenna for a 1‐GHz/2.3‐GHz dual‐frequency sensor application. An auxiliary dipole element generating the higher resonant mode is set on a primary dipole element introducing the lower resonant mode. The feed balance is also designed to cover the desired frequency between two resonance frequencies, which is based on the microstrip line (MS) to coplanar stripline (CPS) transition. To realize the directional antenna, two reflector elements are utilized, and one of them is a stepped‐width reflector on reducing the size of the antenna. In addition, the parasitic strip works as the lumped element used to obtain good impedance matching. A series of simulations are performed on the MS‐to‐CPS transition, the dual dipole element, the reflectors, and the parasitic strip to determine the optimal antenna design. A prototype is fabricated based on the optimal results of the simulation. Concerning the measured results, the proposed antenna has well unidirectional radiations, good radiation efficiencies, and low cross‐polarization levels at any operating frequencies.
- 18 September 2023
- Published by American Geophysical Union (AGU) in Radio Science
- Vol. 58 (9)
Printed Dual‐Frequency Directional Antenna Loaded With Dual‐Parasitic Strip
In this paper, the directional antenna is developed to construct the printed dual‐frequency directional antenna for a 1‐GHz/2.3‐GHz dual‐frequency sensor application. An auxiliary dipole element generating the higher resonant mode is set on a primary dipole element introducing the lower resonant mode. The feed balance is also designed to cover the desired frequency between two resonance frequencies, which is based on the microstrip line (MS) to coplanar stripline (CPS) transition. To realize the directional antenna, two reflector elements are utilized, and one of them is a stepped‐width reflector on reducing the size of the antenna. In addition, the parasitic strip works as the lumped element used to obtain good impedance matching. A series of simulations are performed on the MS‐to‐CPS transition, the dual dipole element, the reflectors, and the parasitic strip to determine the optimal antenna design. A prototype is fabricated based on the optimal results of the simulation. Concerning the measured results, the proposed antenna has well unidirectional radiations, good radiation efficiencies, and low cross‐polarization levels at any operating frequencies.
- Open Access
- 20 July 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 11, 76269-76283
Millimeter-Wave Radar-Based Elderly Fall Detection Fed by One-Dimensional Point Cloud and Doppler
This paper presents an elderly fall detection technique fed by one-dimensional (1-D) point cloud and doppler velocity. In the proposed technique, the long short-term memory (LSTM) network is created and then employed as an intelligent classifier of fall detection. 1-D point clouds and doppler velocity are the input data fed to the LSTM network. Experiments were conducted in order to verify the performance of the proposed fall detection technique. In the experiments, ten participants conducted various continuous sequence activities, for example standing still, walking, sitting, sleeping, simulating a fall, etc., in five different rooms. The millimeter-wave (mmWave) frequency-modulated continuous wave (FMCW) radar was employed to collect radar scattering signals that were transformed into data, including point clouds and doppler velocity. Different types of data grouped as inputs of the LSTM network of the fall detection system were investigated. The accuracy of the training and validation for the proposed system has shown that the point clouds in the z-axis direction and doppler velocity are adequate to be selected as the input data of the LSTM network. The proposed fall detection system can reduce overfitting problems and achieve the least number of input data features, resulting in the least computational complexity compared with state-of-the-art approaches. Before performing fall detection, the data were cleaned by using filtering, and the fault detection was reduced by using sliding window processing. After data preprocessing, the resulting outputs were employed for training and validation of the LSTM network. The window-size effect on the performance of fall detection using point clouds in the z-axis direction and doppler velocity was investigated, and the experimental results have shown that the proposed technique can detect a fall in real time. A fall detected by using the proposed system coincides with the activity of simulating a fall. The accuracy of fall detection using the proposed technique can achieve up to 99.50%.
- 20 July 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 11, 76269-76283
Open AccessMillimeter-Wave Radar-Based Elderly Fall Detection Fed by One-Dimensional Point Cloud and Doppler
This paper presents an elderly fall detection technique fed by one-dimensional (1-D) point cloud and doppler velocity. In the proposed technique, the long short-term memory (LSTM) network is created and then employed as an intelligent classifier of fall detection. 1-D point clouds and doppler velocity are the input data fed to the LSTM network. Experiments were conducted in order to verify the performance of the proposed fall detection technique. In the experiments, ten participants conducted various continuous sequence activities, for example standing still, walking, sitting, sleeping, simulating a fall, etc., in five different rooms. The millimeter-wave (mmWave) frequency-modulated continuous wave (FMCW) radar was employed to collect radar scattering signals that were transformed into data, including point clouds and doppler velocity. Different types of data grouped as inputs of the LSTM network of the fall detection system were investigated. The accuracy of the training and validation for the proposed system has shown that the point clouds in the z-axis direction and doppler velocity are adequate to be selected as the input data of the LSTM network. The proposed fall detection system can reduce overfitting problems and achieve the least number of input data features, resulting in the least computational complexity compared with state-of-the-art approaches. Before performing fall detection, the data were cleaned by using filtering, and the fault detection was reduced by using sliding window processing. After data preprocessing, the resulting outputs were employed for training and validation of the LSTM network. The window-size effect on the performance of fall detection using point clouds in the z-axis direction and doppler velocity was investigated, and the experimental results have shown that the proposed technique can detect a fall in real time. A fall detected by using the proposed system coincides with the activity of simulating a fall. The accuracy of fall detection using the proposed technique can achieve up to 99.50%.
- 29 December 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Antennas and Propagation
- Vol. 70 (5) , 3672-3679
Object Detection of Ground-Penetrating Radar in the Frequency Domain Using Three-Antenna System
An object detection method of ground-penetrating radar (GPR) in the frequency domain using three-antenna system is proposed in this study. The presented methodology utilizes the electromagnetic (EM) scattering from the object for identification using its natural poles. Two schemes of GPR system were examined. The first scheme was the conventional GPR comprising one transmitter and one receiver. The second scheme comprises two transmitters and one receiver, which the transmitters were excited by out-of-phase generators with each other. The simulations were initially performed using the three-antenna system for GPR. The results indicated that the natural poles in the scattering responses changed according to the characteristics of the object. For comparison, the three-antenna system for GPR was fabricated and experimented in comparison with the conventional GPR configuration. The experimental results revealed that the three-antenna configuration was able to mitigate the ground bounce and antenna coupling effects, while the conventional GPR was interfered by the effect of ground reflection and mutual coupling of the antennas. The three-antenna configuration is thus suitable to be the front-end before extracting the natural poles. In addition, the frequency domain method is compatible with the three-antenna system in the determination of the natural poles for identification. As such, the proposed system for investigating the response in the frequency domain is operationally appropriate in GPR system.
- 29 December 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Antennas and Propagation
- Vol. 70 (5) , 3672-3679
Object Detection of Ground-Penetrating Radar in the Frequency Domain Using Three-Antenna System
An object detection method of ground-penetrating radar (GPR) in the frequency domain using three-antenna system is proposed in this study. The presented methodology utilizes the electromagnetic (EM) scattering from the object for identification using its natural poles. Two schemes of GPR system were examined. The first scheme was the conventional GPR comprising one transmitter and one receiver. The second scheme comprises two transmitters and one receiver, which the transmitters were excited by out-of-phase generators with each other. The simulations were initially performed using the three-antenna system for GPR. The results indicated that the natural poles in the scattering responses changed according to the characteristics of the object. For comparison, the three-antenna system for GPR was fabricated and experimented in comparison with the conventional GPR configuration. The experimental results revealed that the three-antenna configuration was able to mitigate the ground bounce and antenna coupling effects, while the conventional GPR was interfered by the effect of ground reflection and mutual coupling of the antennas. The three-antenna configuration is thus suitable to be the front-end before extracting the natural poles. In addition, the frequency domain method is compatible with the three-antenna system in the determination of the natural poles for identification. As such, the proposed system for investigating the response in the frequency domain is operationally appropriate in GPR system.
- 6 April 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Instrumentation and Measurement
- Vol. 69 (10) , 7617-7626
Dual-Frequency Sensor for Thick Rind Fruit Quality Assessment
- 6 April 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Instrumentation and Measurement
- Vol. 69 (10) , 7617-7626
Dual-Frequency Sensor for Thick Rind Fruit Quality Assessment
- 28 November 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Antennas and Propagation
- Vol. 67 (4) , 2056-2062
Measurement of Radiated Field From Transmitting Antennas Located in Various Environments
- 28 November 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Antennas and Propagation
- Vol. 67 (4) , 2056-2062
Measurement of Radiated Field From Transmitting Antennas Located in Various Environments
- 1 December 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 128-129
Detecting granulated fruit by measuring dual-frequency back scattered waves
Granulation is a kind of defection in fruits that must be non-destructively detected. Electromagnetic wave measurement is a feasible technique for in-situ measurement. With thick peel, it is necessary to eliminate the effect of peel so that sole effect of variation of pulp can be detected. This paper presents the simulated scattering coefficient from fruit with dual-frequency that exhibits more obvious results than the single-frequency measurement. The results lead to the appropriate design of a sensor for granulation detection.
- 1 December 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 128-129
Detecting granulated fruit by measuring dual-frequency back scattered waves
Granulation is a kind of defection in fruits that must be non-destructively detected. Electromagnetic wave measurement is a feasible technique for in-situ measurement. With thick peel, it is necessary to eliminate the effect of peel so that sole effect of variation of pulp can be detected. This paper presents the simulated scattering coefficient from fruit with dual-frequency that exhibits more obvious results than the single-frequency measurement. The results lead to the appropriate design of a sensor for granulation detection.
- 1 October 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-2
A switch-beam circular array antenna using pattern reconfigurable Yagi-Uda antenna for space communications
This paper presents a switch-beam circular array antenna using pattern reconfigurable Yagi-Uda antenna. A two-beam switching Yagi-Uda antenna is applied as an array element. The 3-element circular array is introduced to be able to switch the main beam in azimuth direction by switching the beam and shifting the excitation phase of array elements. The array antenna is designed at 2.4 GHz for drone or UAV radio controlling. The two-beam elements and 90°-shifted phase of excitation are applied to realize the proposed switched-beam array antenna. The simulated results show that the array antenna can provide 7 main beam directions covering a half azimuth plane (0° ≤ φ ≤ 180°) and gain of the array antenna is higher than 7 dBi.
- 1 October 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-2
A switch-beam circular array antenna using pattern reconfigurable Yagi-Uda antenna for space communications
This paper presents a switch-beam circular array antenna using pattern reconfigurable Yagi-Uda antenna. A two-beam switching Yagi-Uda antenna is applied as an array element. The 3-element circular array is introduced to be able to switch the main beam in azimuth direction by switching the beam and shifting the excitation phase of array elements. The array antenna is designed at 2.4 GHz for drone or UAV radio controlling. The two-beam elements and 90°-shifted phase of excitation are applied to realize the proposed switched-beam array antenna. The simulated results show that the array antenna can provide 7 main beam directions covering a half azimuth plane (0° ≤ φ ≤ 180°) and gain of the array antenna is higher than 7 dBi.
- 1 September 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 47-48
Dual-band unidirectional cross dipole antenna
This paper presents a dual-band unidirectional antenna based on a straight dipole shunted with a meander line dipole antenna. This antenna is fed with a wide band Balun and equipped with reflectors to generate unidirectional patterns. The low and high frequency reflectors are plane and box reflectors, respectively. The antenna is well matched at the designed frequencies of 1 and 2 GHz. The unidirectional patterns are obtained at both frequencies with gain higher than 5.7 dBi. This antenna is used for illuminating microwave signal to an object under-test in a dual-band reflectometer.
- 1 September 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 47-48
Dual-band unidirectional cross dipole antenna
This paper presents a dual-band unidirectional antenna based on a straight dipole shunted with a meander line dipole antenna. This antenna is fed with a wide band Balun and equipped with reflectors to generate unidirectional patterns. The low and high frequency reflectors are plane and box reflectors, respectively. The antenna is well matched at the designed frequencies of 1 and 2 GHz. The unidirectional patterns are obtained at both frequencies with gain higher than 5.7 dBi. This antenna is used for illuminating microwave signal to an object under-test in a dual-band reflectometer.
- 1 July 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1979-1980
Dual-band conical-scanning Yagi-Uda antenna
A dual-band conical-scanning Yagi-Uda antenna is presented. The proposed antenna is composed of dual-band director elements, dual-band driven elements, and planar reflectors which the alignment of each element is not on the same plane of the dual-band driven elements. The PIN diodes are used in order to change position of driven elements and directors. The patterns can be switched in four directions that main beams are in the zenith angle of 30°. It is shown that the dual-band antenna for 1 and 2 GHz operation achieves an impedance bandwidth of 8.5% and 12.5%, respectively. The front-to-back ratio of conical beams is higher than 8 dB. The antenna gain is around 6 dBi.
- 1 July 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1979-1980
Dual-band conical-scanning Yagi-Uda antenna
A dual-band conical-scanning Yagi-Uda antenna is presented. The proposed antenna is composed of dual-band director elements, dual-band driven elements, and planar reflectors which the alignment of each element is not on the same plane of the dual-band driven elements. The PIN diodes are used in order to change position of driven elements and directors. The patterns can be switched in four directions that main beams are in the zenith angle of 30°. It is shown that the dual-band antenna for 1 and 2 GHz operation achieves an impedance bandwidth of 8.5% and 12.5%, respectively. The front-to-back ratio of conical beams is higher than 8 dB. The antenna gain is around 6 dBi.