Anvar Kadyrmetov
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Anvar Kadyrmetov has a total of 29 co-authors. Here are the top co-authors by number of shared publications:
Aleksandr Plahotin
3 shared publications- S. N. Sharifullin
Kazan Federal University, Russia
3 shared publications - Dmitrii Popov
Voronezh State University of Forestry and Technologies named after G.F. Morozov
2 shared publications - Eugeni Pamfilov
Bryansk State Technical University
2 shared publications Evgenij Snyatkov
2 shared publicationsIgor' Mandrykin
2 shared publications
Latest Publications
- Open Access
- 7 April 2025
- Published by Voronezh State University of Forestry and Technologies named after G.F. Morozov in Voronezh Scientific-Technical Bulletin
- Vol. 1 (1) , 12-24
ASSESSMENT OF THERMOMECHANICAL PROCESSING FORCES WITH ROLLER TOOL OF GAS-THERMAL COATINGS BASED ON NICKEL
An effective method of thermomechanical hardening of nickel-based gas-thermal coatings is considered in the aspect of assessing the forces of their rolling with a roller tool. The rolling force depends on the specified value of plastic deformation of the coatings, the coating temperature in the range of 273...1473 K, the deformation rate and geometric parameters of the roller and the processed cylindrical surface of the coating.
- 7 April 2025
- Published by Voronezh State University of Forestry and Technologies named after G.F. Morozov in Voronezh Scientific-Technical Bulletin
- Vol. 1 (1) , 12-24
Open AccessASSESSMENT OF THERMOMECHANICAL PROCESSING FORCES WITH ROLLER TOOL OF GAS-THERMAL COATINGS BASED ON NICKEL
An effective method of thermomechanical hardening of nickel-based gas-thermal coatings is considered in the aspect of assessing the forces of their rolling with a roller tool. The rolling force depends on the specified value of plastic deformation of the coatings, the coating temperature in the range of 273...1473 K, the deformation rate and geometric parameters of the roller and the processed cylindrical surface of the coating.
- Open Access
- 13 October 2023
- Published by Voronezh State University of Forestry and Technologies named after G.F. Morozov in Voronezh Scientific-Technical Bulletin
- Vol. 3 (3) , 34-47
STRENGTHENING WEAR PARTSSURFACES OF FORESTRY MACHINERY PARTS BY PLASMA APPLICATION AND HARDENING OF COATINGS OF VARIABLE COMPOSITION
- 13 October 2023
- Published by Voronezh State University of Forestry and Technologies named after G.F. Morozov in Voronezh Scientific-Technical Bulletin
- Vol. 3 (3) , 34-47
Open AccessSTRENGTHENING WEAR PARTSSURFACES OF FORESTRY MACHINERY PARTS BY PLASMA APPLICATION AND HARDENING OF COATINGS OF VARIABLE COMPOSITION
- Open Access
- 3 November 2022
- Published by Voronezh State University of Forestry and Technologies named after G.F. Morozov in Voronezh Scientific-Technical Bulletin
- Vol. 1 (1) , 3-14
PERSPECTIVE DIRECTIONS OF IMPROVEMENT OF PLASMA SPRAYING TECHNOLOGY WITH P ULSE MODULATION OF THE ARC CURRENT
- 3 November 2022
- Published by Voronezh State University of Forestry and Technologies named after G.F. Morozov in Voronezh Scientific-Technical Bulletin
- Vol. 1 (1) , 3-14
Open AccessPERSPECTIVE DIRECTIONS OF IMPROVEMENT OF PLASMA SPRAYING TECHNOLOGY WITH P ULSE MODULATION OF THE ARC CURRENT
- Open Access
- 2 February 2022
- Published by Voronezh State University of Forestry and Technologies named after G.F. Morozov in Voronezh Scientific-Technical Bulletin
- Vol. 3 (3) , 28-35
FACTOR PLANNING OF AN EXPERIMENT FOR ESTIMATING THE OPTIMAL PROPERTIES OF HEAT PROTECTIVE COATINGS ON DETAILS OF A CYLINDER-PISTON GROUP OF DIESEL ENGINES
- 2 February 2022
- Published by Voronezh State University of Forestry and Technologies named after G.F. Morozov in Voronezh Scientific-Technical Bulletin
- Vol. 3 (3) , 28-35
Open AccessFACTOR PLANNING OF AN EXPERIMENT FOR ESTIMATING THE OPTIMAL PROPERTIES OF HEAT PROTECTIVE COATINGS ON DETAILS OF A CYLINDER-PISTON GROUP OF DIESEL ENGINES
- Open Access
- 25 January 2022
- Published by Voronezh State University of Forestry and Technologies named after G.F. Morozov in Voronezh Scientific-Technical Bulletin
- Vol. 2 (2) , 10-16
PROPERTIES OF PLASMA COATINGS SPRAYED IN ARC POWER MODULA-TION MODE
In this paper, it is shown that by modulating a plasma arc, as well as the use of an air-gas mix-ture (air with propane-butane), you can signifi-cantly increase the strength of the coating coat-ing, the coefficient of use of the powder, reduce gas permeability and increase the wear resistance of plasma powder coatings.
- 25 January 2022
- Published by Voronezh State University of Forestry and Technologies named after G.F. Morozov in Voronezh Scientific-Technical Bulletin
- Vol. 2 (2) , 10-16
Open AccessPROPERTIES OF PLASMA COATINGS SPRAYED IN ARC POWER MODULA-TION MODE
In this paper, it is shown that by modulating a plasma arc, as well as the use of an air-gas mix-ture (air with propane-butane), you can signifi-cantly increase the strength of the coating coat-ing, the coefficient of use of the powder, reduce gas permeability and increase the wear resistance of plasma powder coatings.
- Open Access
- 1 July 2019
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 570 (1)
Technological Support of Plasma Coating with the Plasmatron Power Modulation
- 1 July 2019
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 570 (1)
Open AccessTechnological Support of Plasma Coating with the Plasmatron Power Modulation
- Open Access
- 30 October 2018
- Published by EDP Sciences in MATEC Web of Conferences
- Vol. 224, 03009
Optimization of process of application plasma hardening coating
This article addresses the problem of increasing tool life by applying a wear-resisting coating. However, the lack of technology-based methods and optimal regimes complicate this process. A method for finishing plasma hardening of metals which allows evaluate the quality of the wear-resistant thin-film coatings and optimize application regimes have been advanced.
- 30 October 2018
- Published by EDP Sciences in MATEC Web of Conferences
- Vol. 224, 03009
Open AccessOptimization of process of application plasma hardening coating
This article addresses the problem of increasing tool life by applying a wear-resisting coating. However, the lack of technology-based methods and optimal regimes complicate this process. A method for finishing plasma hardening of metals which allows evaluate the quality of the wear-resistant thin-film coatings and optimize application regimes have been advanced.
- Open Access
- 1 November 2016
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 158 (1) , 012045
Physical processes and modeling of plasma deposition and hardening of coatings-switched electrical parameters
This paper presents the results of simulation of plasma deposition and hardening of coatings in modulating the electrical parameters. Mathematical models are based on physical models of gas-dynamic mechanisms more dynamic and thermal processes of the plasma jet. As an example the modeling of dynamic processes of heterogeneous plasma jet, modulated current pulses indirect arc plasma torch.
- 1 November 2016
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 158 (1) , 012045
Open AccessPhysical processes and modeling of plasma deposition and hardening of coatings-switched electrical parameters
This paper presents the results of simulation of plasma deposition and hardening of coatings in modulating the electrical parameters. Mathematical models are based on physical models of gas-dynamic mechanisms more dynamic and thermal processes of the plasma jet. As an example the modeling of dynamic processes of heterogeneous plasma jet, modulated current pulses indirect arc plasma torch.
- Open Access
- 1 June 2016
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 134 (1) , 012010
Efficiency of surface cleaning by a glow discharge for plasma spraying coating
The article presents the results of experimental studies of the quality of cleaning steel surfaces by a glow discharge for plasma spraying. Shows the results of measurements of the angle of surface wetting and bond strength of the plasma coating to the surface treated. The dependence of the influence of the glow discharge power, chamber pressure, distance between the electrodes and the processing time of the surface on cleaning efficiency. Optimal fields of factors is found. It is shown increase joint strength coating and base by 30-80% as a result of cleaning the substrate surface by a glow discharge plasma spraying.
- 1 June 2016
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 134 (1) , 012010
Open AccessEfficiency of surface cleaning by a glow discharge for plasma spraying coating
The article presents the results of experimental studies of the quality of cleaning steel surfaces by a glow discharge for plasma spraying. Shows the results of measurements of the angle of surface wetting and bond strength of the plasma coating to the surface treated. The dependence of the influence of the glow discharge power, chamber pressure, distance between the electrodes and the processing time of the surface on cleaning efficiency. Optimal fields of factors is found. It is shown increase joint strength coating and base by 30-80% as a result of cleaning the substrate surface by a glow discharge plasma spraying.