S. N. Sharifullin
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
S. N. Sharifullin has a total of 62 co-authors. Here are the top co-authors by number of shared publications:
- Yuri Alekseevich Kuznetsov
Parakhin Orel State Agrarian University, Oryol, Russia
7 shared publications - Alexander V. Kolomeichenko
Parakhin Orel State Agrarian University
5 shared publications N R Adigamov
Kazan State Agrarian university, Russia
4 shared publicationsN V Titov
Orel State Agrarian University named after N.V. Parakhin, Russia
4 shared publications- Anvar Kadyrmetov
Voronezh State University of Forestry and Technologies named after G.F. Morozov
3 shared publications L V Kalashnikova
Orel State University named after I.S. Turgenev, Russia
3 shared publications
Latest Publications
- 29 August 2025
- Published by PANORAMA Publishing House in Sel'skohozjajstvennaja tehnika: obsluzhivanie i remont (Agricultural Machinery: Service and Repair)
- No. 8,p. 48-55
Unassembled repair of internal combustion engines with tribosystems
The article summarizes data on excessive water release from the exhaust tract of an internal combustion engine during its tribo-treatment with serpentine compounds, which does not correspond to conventional ideas about the operation of an internal combustion engine. The article presents some theories about the causes of this phenomenon, which is a sign of the beginning of a non-disassembled repair of worn-out engine joints. To optimize this process, it is proposed to adjust the dose of the introduced tribo-compound according to the nature of water release. The need to create a methodology for assessing the digital maturity of maintenance and repair processes and determining priority areas for digitalization was discussed.
- 29 August 2025
- Published by PANORAMA Publishing House in Sel'skohozjajstvennaja tehnika: obsluzhivanie i remont (Agricultural Machinery: Service and Repair)
- No. 8,p. 48-55
Unassembled repair of internal combustion engines with tribosystems
The article summarizes data on excessive water release from the exhaust tract of an internal combustion engine during its tribo-treatment with serpentine compounds, which does not correspond to conventional ideas about the operation of an internal combustion engine. The article presents some theories about the causes of this phenomenon, which is a sign of the beginning of a non-disassembled repair of worn-out engine joints. To optimize this process, it is proposed to adjust the dose of the introduced tribo-compound according to the nature of water release. The need to create a methodology for assessing the digital maturity of maintenance and repair processes and determining priority areas for digitalization was discussed.
- 8 September 2023
- Published by Pleiades Publishing Ltd in High Energy Chemistry
- Vol. 57 (S1) , S193-S199
Simulation of the Process of Electric Spark Hardening of the Surfaces of Machine Parts and Mechanisms
Today, there is a sharp struggle for demanded and competitive products all over the world. The existing traditional production technologies have exhausted their possibilities. New technologies should be based on high energy technologies. One of such technologies is plasma technologies. Among the plasma technologies for hardening metal surfaces, the most suitable is the hardening technology using electric spark discharges. However, these technologies do not currently have process optimization. This article proposes one of the options for solving this problem by simulating the process of electrospark alloying of elements of refractory materials into the surface layer of samples of real parts of machines and mechanisms, which are models of these parts.
- 8 September 2023
- Published by Pleiades Publishing Ltd in High Energy Chemistry
- Vol. 57 (S1) , S193-S199
Simulation of the Process of Electric Spark Hardening of the Surfaces of Machine Parts and Mechanisms
Today, there is a sharp struggle for demanded and competitive products all over the world. The existing traditional production technologies have exhausted their possibilities. New technologies should be based on high energy technologies. One of such technologies is plasma technologies. Among the plasma technologies for hardening metal surfaces, the most suitable is the hardening technology using electric spark discharges. However, these technologies do not currently have process optimization. This article proposes one of the options for solving this problem by simulating the process of electrospark alloying of elements of refractory materials into the surface layer of samples of real parts of machines and mechanisms, which are models of these parts.
- Open Access
- 1 September 2020
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 915 (1) , 012045
Evaluation of the wear resistance and resource hardened by electrospark machining of the cutting surfaces of the fingers of the headers of combine harvesters
The article presents the technology of hardening the fingers of the reapers of combine harvesters by electrospark processing. To strengthen the cutting surfaces of the fingers, it is recommended to use an amorphous alloy grade 84KXSR. The operational tests presented in the work showed that wear and dulling of both serial products and experimental parts with electric spark coatings is characterized by two stages: running-in and natural wear. The running-in occurs during the running time of the fingers in 1 ha. The results of operational tests showed that the application of a wear-resistant electrospark coating of amorphous alloy grade 84KXSR with a thickness of 30 μm and a track width of 2 mm on the cutting surfaces of the fingers of the headers of grain harvesters makes it possible to increase the resource from 1.4 to 2 times.
- 1 September 2020
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 915 (1) , 012045
Open AccessEvaluation of the wear resistance and resource hardened by electrospark machining of the cutting surfaces of the fingers of the headers of combine harvesters
The article presents the technology of hardening the fingers of the reapers of combine harvesters by electrospark processing. To strengthen the cutting surfaces of the fingers, it is recommended to use an amorphous alloy grade 84KXSR. The operational tests presented in the work showed that wear and dulling of both serial products and experimental parts with electric spark coatings is characterized by two stages: running-in and natural wear. The running-in occurs during the running time of the fingers in 1 ha. The results of operational tests showed that the application of a wear-resistant electrospark coating of amorphous alloy grade 84KXSR with a thickness of 30 μm and a track width of 2 mm on the cutting surfaces of the fingers of the headers of grain harvesters makes it possible to increase the resource from 1.4 to 2 times.
- 30 October 2019
- Published by Kazan State Agrarian University in Vestnik of Kazan State Agrarian University
- Vol. 14 (3) , 128-132
CLASSIFICATION OF STRENGTHENING TECHNOLOGIES, COVERING AND RESTORATION OF FUEL EQUIPMENT DETAILS OF DIESEL ENGINES
During operation, any technical product with friction units, as parts wear out, loses its working capacity and as a result cannot perform the specified functions with the parameters, established by the requirements of technical documentation. Today, the technological capabilities of manufacturing various machines and mechanisms have been exhausted throughout the world without noticeable wear on the mating surfaces of friction units. Depreciation is practically impossible to exclude. Therefore, a search for new ways to extend the life of technical devices by exposing them to friction surfaces is an urgent task. These requirements apply to the fuel equipment of automotive and combine diesel engines. In this paper, we analyze the known covering technologies for hardening and restoration of fuel equipment parts. The methodology of choosing the optimal covering process with the aim of hardening and restoration of parts of fuel equipment is formulated. In accordance with this concept of choosing a technology to increase the durability of fuel equipment parts, plasma finish hardening with the application of multilayer wear-resistant coatings is a promising technology. The paper presents the results of a study of the physicomechanical properties of diamond-like coverings of the DLCPateks type (a-C:H/a-SiOCN) obtained on friction surfaces by transporting an atomic and molecular stream of particles of liquid chemical compounds by a plasma jet of an atmospheric pressure plasma arc torch. The layer formed on the working surfaces is a non-metallic amorphous multilayer covering with a low coefficient of friction, increased microhardness, chemical inertness, hydrophilicity, high heat resistance and dielectric characteristics. In order to minimize possible defectiveness of the base material at the final stage of manufacturing parts of fuel equipment, it is proposed to apply thin-film coatings on them.
- 30 October 2019
- Published by Kazan State Agrarian University in Vestnik of Kazan State Agrarian University
- Vol. 14 (3) , 128-132
CLASSIFICATION OF STRENGTHENING TECHNOLOGIES, COVERING AND RESTORATION OF FUEL EQUIPMENT DETAILS OF DIESEL ENGINES
During operation, any technical product with friction units, as parts wear out, loses its working capacity and as a result cannot perform the specified functions with the parameters, established by the requirements of technical documentation. Today, the technological capabilities of manufacturing various machines and mechanisms have been exhausted throughout the world without noticeable wear on the mating surfaces of friction units. Depreciation is practically impossible to exclude. Therefore, a search for new ways to extend the life of technical devices by exposing them to friction surfaces is an urgent task. These requirements apply to the fuel equipment of automotive and combine diesel engines. In this paper, we analyze the known covering technologies for hardening and restoration of fuel equipment parts. The methodology of choosing the optimal covering process with the aim of hardening and restoration of parts of fuel equipment is formulated. In accordance with this concept of choosing a technology to increase the durability of fuel equipment parts, plasma finish hardening with the application of multilayer wear-resistant coatings is a promising technology. The paper presents the results of a study of the physicomechanical properties of diamond-like coverings of the DLCPateks type (a-C:H/a-SiOCN) obtained on friction surfaces by transporting an atomic and molecular stream of particles of liquid chemical compounds by a plasma jet of an atmospheric pressure plasma arc torch. The layer formed on the working surfaces is a non-metallic amorphous multilayer covering with a low coefficient of friction, increased microhardness, chemical inertness, hydrophilicity, high heat resistance and dielectric characteristics. In order to minimize possible defectiveness of the base material at the final stage of manufacturing parts of fuel equipment, it is proposed to apply thin-film coatings on them.
- Open Access
- 1 October 2019
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 1328 (1) , 012099
Properties of coatings formed by plasma electrolytic oxidation on plastically deformed aluminum alloy AO3-7
The article presents the research results of the influence of electrolyte composition and plasma electrolyte oxidation (PEO) modes on microhardness and wear resistance of coating formed on a bush of the gear type pump HШ-У, which is reconditioned by plastic deformation.
- 1 October 2019
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 1328 (1) , 012099
Open AccessProperties of coatings formed by plasma electrolytic oxidation on plastically deformed aluminum alloy AO3-7
The article presents the research results of the influence of electrolyte composition and plasma electrolyte oxidation (PEO) modes on microhardness and wear resistance of coating formed on a bush of the gear type pump HШ-У, which is reconditioned by plastic deformation.
- Open Access
- 1 October 2019
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 1328 (1) , 012100
Some characteristics of surface hardening of steel 65g in the electric-spark method
The paper presents the results of studies of some physical and mechanical properties of metal samples made of 65G steel, hardened by electrospark method. Researches are connected with the solution of problems of increase of a resource of work of details and working bodies of agricultural machines. The elemental composition, phase composition and microstructure of the surface of 65G steel samples processed by the electrospark method were investigated.
- 1 October 2019
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 1328 (1) , 012100
Open AccessSome characteristics of surface hardening of steel 65g in the electric-spark method
The paper presents the results of studies of some physical and mechanical properties of metal samples made of 65G steel, hardened by electrospark method. Researches are connected with the solution of problems of increase of a resource of work of details and working bodies of agricultural machines. The elemental composition, phase composition and microstructure of the surface of 65G steel samples processed by the electrospark method were investigated.
- Open Access
- 1 October 2019
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 1328 (1) , 012006
Structure of the mathematical model of applying wear-resistant coatings by a high-frequency induction plasma of low pressure
Annotation: In this scientific work, we proposed a scheme for the transformation of a physical model of applying the HFI plasma coating to a mathematical one in a mathematical way by stepwise solving the problems of the structural model stages. The equations of conservation of energy of the electron gas, Maxwell, continuity and momentum will be used. It is planned to develop a mathematical model for sputtering dielectric and metallic materials. In this case, boundary conditions will be introduced for the discharge power, flow rate and gas types, pressure and design parameters of the plasma torch.
- 1 October 2019
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 1328 (1) , 012006
Open AccessStructure of the mathematical model of applying wear-resistant coatings by a high-frequency induction plasma of low pressure
Annotation: In this scientific work, we proposed a scheme for the transformation of a physical model of applying the HFI plasma coating to a mathematical one in a mathematical way by stepwise solving the problems of the structural model stages. The equations of conservation of energy of the electron gas, Maxwell, continuity and momentum will be used. It is planned to develop a mathematical model for sputtering dielectric and metallic materials. In this case, boundary conditions will be introduced for the discharge power, flow rate and gas types, pressure and design parameters of the plasma torch.
- Open Access
- 1 October 2019
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 1328 (1) , 012038
Dual-program impulse modulation of plasmatron power in processes of plasma spraying
On the basis of analysis of plasma coating processes the influence of electrical parameters modulation of the remote arc on the temperature field in the “coating-base” system in the local scale, proportional to the diameter of the arc binding spot to the surface, and in the macro scale of sprayed surface is valued. Dual-program impulse modulation of plasmatron power, providing uniform distribution of the coating connection strength with the substrate layer based on uniform distribution of surface thermal activation and local zones of coating penetration on the sprayed surface is offered.
- 1 October 2019
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 1328 (1) , 012038
Open AccessDual-program impulse modulation of plasmatron power in processes of plasma spraying
On the basis of analysis of plasma coating processes the influence of electrical parameters modulation of the remote arc on the temperature field in the “coating-base” system in the local scale, proportional to the diameter of the arc binding spot to the surface, and in the macro scale of sprayed surface is valued. Dual-program impulse modulation of plasmatron power, providing uniform distribution of the coating connection strength with the substrate layer based on uniform distribution of surface thermal activation and local zones of coating penetration on the sprayed surface is offered.
- Open Access
- 1 October 2019
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 1328 (1) , 012096
Estimation of wear resistance of oxide and ceramic coatings in the hydrobrasive wear conditions
For wear compensation of the components made from aluminum alloys and operated in the conditions of hydroabrasive wear, we suggest the method of reconditioning and hardening, which combines the advantages of deposition in the argon medium and plasma electrolytic oxidation. The model of hydroabrasive wear of oxide and ceramic coatings obtained by plasma electrolytic oxidation is suggested. The requirements to the composition and structure of coatings at their usage in the hydroabrasive wear conditions are reasoned.
- 1 October 2019
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 1328 (1) , 012096
Open AccessEstimation of wear resistance of oxide and ceramic coatings in the hydrobrasive wear conditions
For wear compensation of the components made from aluminum alloys and operated in the conditions of hydroabrasive wear, we suggest the method of reconditioning and hardening, which combines the advantages of deposition in the argon medium and plasma electrolytic oxidation. The model of hydroabrasive wear of oxide and ceramic coatings obtained by plasma electrolytic oxidation is suggested. The requirements to the composition and structure of coatings at their usage in the hydroabrasive wear conditions are reasoned.
- Open Access
- 1 October 2019
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 1328 (1) , 012097
About the role of tribroplasma in the process of water extract from the exhaust tract of the engine of internal combustion when treating them by tribosettes
The abundant water release during the processing of ICE by tribosystems was observed by many practitioners of PBC repair. The hypotheses of its causes are ambiguous. Some say that the source of water is motor oil or decomposition of pollution of ICE. Others believe that the source of water is humid air. Still others emphasize that water emission is concealed in the exhaust tract of the engine with neutralizers and turbochargers. There is a saying that this is just a condensate discharge from the engine exhaust tract. However, abundant water release occurs only with the introduction of the PBC drug in the friction unit. It is believed that the main reason is associated with the presence of triboplasma, which is formed when the contact spots of the friction site mating surfaces come off. In the area of triboplasm, the tribopreparation undergoes a plasma-chemical reaction, is split with the release of high thermal energy, which creates other conditions for moist air, fuel, engine oil and ICE pollution. All interpretations of the causes of water emission may be erroneous, since it contradicts the prevailing ideas about the work of the internal combustion engine.
- 1 October 2019
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 1328 (1) , 012097
Open AccessAbout the role of tribroplasma in the process of water extract from the exhaust tract of the engine of internal combustion when treating them by tribosettes
The abundant water release during the processing of ICE by tribosystems was observed by many practitioners of PBC repair. The hypotheses of its causes are ambiguous. Some say that the source of water is motor oil or decomposition of pollution of ICE. Others believe that the source of water is humid air. Still others emphasize that water emission is concealed in the exhaust tract of the engine with neutralizers and turbochargers. There is a saying that this is just a condensate discharge from the engine exhaust tract. However, abundant water release occurs only with the introduction of the PBC drug in the friction unit. It is believed that the main reason is associated with the presence of triboplasma, which is formed when the contact spots of the friction site mating surfaces come off. In the area of triboplasm, the tribopreparation undergoes a plasma-chemical reaction, is split with the release of high thermal energy, which creates other conditions for moist air, fuel, engine oil and ICE pollution. All interpretations of the causes of water emission may be erroneous, since it contradicts the prevailing ideas about the work of the internal combustion engine.