Mostafa Alizadeh
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Mostafa Alizadeh has a total of 45 co-authors. Here are the top co-authors by number of shared publications:
- Mohsen Hajizamani
Central laboratory of Shiraz University, Shiraz, Iran
5 shared publications Sajjad Bordbar
3 shared publicationsAhmad Jenabali Jahromi
2 shared publicationsAli Alizadeh
Faculty of Materials & Manufacturing Processes, Malek-Ashtar University of Technology, Tehran, Iran
2 shared publicationsEsmaeel Darezereshki
2 shared publicationsFereshteh Bakhtiari
2 shared publications
Latest Publications
- 11 June 2025
- Published by Springer Nature in Transactions of the Indian Institute of Metals
- Vol. 78 (7) , 1-8
On the Electrical Conductivity of Al–3.5 wt%Si Alloy After Homogenization Heat Treatment and Subsequent Aging
- 11 June 2025
- Published by Springer Nature in Transactions of the Indian Institute of Metals
- Vol. 78 (7) , 1-8
On the Electrical Conductivity of Al–3.5 wt%Si Alloy After Homogenization Heat Treatment and Subsequent Aging
- 1 September 2020
- Published by Elsevier in Materials Letters
- Vol. 275, 128085
Improvement of microstructure and corrosion properties of AA7075 Al alloy by melt shearing process
- 1 September 2020
- Published by Elsevier in Materials Letters
- Vol. 275, 128085
Improvement of microstructure and corrosion properties of AA7075 Al alloy by melt shearing process
- 8 February 2019
- Published by EDP Sciences in Metallurgical Research & Technology
- Vol. 116 (2) , 213
A comprehensive study on synthesis behavior of nanostructured Al-Zn-Mg-Cu alloy powder with and without 3 wt.% Al2O3 particles during mechanical alloying
The mechanical alloying (MA) process was applied to synthesize nanostructured Al-Zn-Mg-Cu alloy powder and its composite with 3 wt.% Al2O3 particles. Both the alloy and the composite powders were produced by simultaneous milling of the constituents for different milling times (0–50 hours), with fixed milling technical parameters. The produced powders were characterized by the X-ray diffraction (XRD) analysis to detect the generated phases. Also, a scanning electron microscope (SEM) and a transmission electron microscope (TEM) were used to observe the morphologies and measure the crystallite size of the powders, respectively. It was found that during the production of the composite powder, the size of Al2O3 particle changed which led to unexpected outcomes. In the alloy state, the average particle size and the crystallite size were lower and the microhardness values were higher than those in the composite powder. Also, the steady state was achieved after a shorter MA time in the alloy state compared to the composite state. The major reason for these results was the changes of alumina particle size in the composite powders at the first stages of the MA process due to consuming a noticeable amount of energy, which made them ineffective. In addition, the compressibility in the composite powders was lower than that of the alloy powders due to the presence of alumina particles. Moreover, in both powders, the compressibility decreased with increasing the MA time because of the increased work hardening and the reduced flow properties.
- 8 February 2019
- Published by EDP Sciences in Metallurgical Research & Technology
- Vol. 116 (2) , 213
A comprehensive study on synthesis behavior of nanostructured Al-Zn-Mg-Cu alloy powder with and without 3 wt.% Al2O3 particles during mechanical alloying
The mechanical alloying (MA) process was applied to synthesize nanostructured Al-Zn-Mg-Cu alloy powder and its composite with 3 wt.% Al2O3 particles. Both the alloy and the composite powders were produced by simultaneous milling of the constituents for different milling times (0–50 hours), with fixed milling technical parameters. The produced powders were characterized by the X-ray diffraction (XRD) analysis to detect the generated phases. Also, a scanning electron microscope (SEM) and a transmission electron microscope (TEM) were used to observe the morphologies and measure the crystallite size of the powders, respectively. It was found that during the production of the composite powder, the size of Al2O3 particle changed which led to unexpected outcomes. In the alloy state, the average particle size and the crystallite size were lower and the microhardness values were higher than those in the composite powder. Also, the steady state was achieved after a shorter MA time in the alloy state compared to the composite state. The major reason for these results was the changes of alumina particle size in the composite powders at the first stages of the MA process due to consuming a noticeable amount of energy, which made them ineffective. In addition, the compressibility in the composite powders was lower than that of the alloy powders due to the presence of alumina particles. Moreover, in both powders, the compressibility decreased with increasing the MA time because of the increased work hardening and the reduced flow properties.
- 1 February 2018
- Published by IOP Publishing in Materials Research Express
- Vol. 5 (2) , 026520
Role of melt percentage on characteristics of Al-Zn-Mg/3 wt.% Al2O3 nanostructured composite modified through semi-solid thermomechanical processing
- 1 February 2018
- Published by IOP Publishing in Materials Research Express
- Vol. 5 (2) , 026520
Role of melt percentage on characteristics of Al-Zn-Mg/3 wt.% Al2O3 nanostructured composite modified through semi-solid thermomechanical processing
- 25 November 2017
- Published by Walter de Gruyter GmbH in International Journal of Materials Research
- Vol. 108 (12) , 1073-1080
A study on effects of a new two-step strain induced melt activation process on characteristics of Al 7075 alloy
It is well-known that the strain induced melt activation process results in a globular microstructure which improves the hardness and the ultimate tensile stress. However, its disadvantage is degrading some other properties such as elongation and formability due to the presence of continuous and brittle intermetallic compounds along with the formation of eutectic structures at grain boundaries. Hence, the aim of this research is to introduce a new process called two-step strain induced melt activation to overcome these drawbacks and to improve the microstructure and the formability of Al 7075 alloy. This new process yielded a globular structure and modified the microstructure. Also, the resultant precipitates were discontinuous with a more homogeneous distribution and the eutectic mixture was eliminated. Moreover, the alloy formability and the hardness were effectively enhanced by performing a rolling process.
- 25 November 2017
- Published by Walter de Gruyter GmbH in International Journal of Materials Research
- Vol. 108 (12) , 1073-1080
A study on effects of a new two-step strain induced melt activation process on characteristics of Al 7075 alloy
It is well-known that the strain induced melt activation process results in a globular microstructure which improves the hardness and the ultimate tensile stress. However, its disadvantage is degrading some other properties such as elongation and formability due to the presence of continuous and brittle intermetallic compounds along with the formation of eutectic structures at grain boundaries. Hence, the aim of this research is to introduce a new process called two-step strain induced melt activation to overcome these drawbacks and to improve the microstructure and the formability of Al 7075 alloy. This new process yielded a globular structure and modified the microstructure. Also, the resultant precipitates were discontinuous with a more homogeneous distribution and the eutectic mixture was eliminated. Moreover, the alloy formability and the hardness were effectively enhanced by performing a rolling process.
- 28 September 2017
- Published by Walter de Gruyter GmbH in International Journal of Materials Research
- Vol. 108 (10) , 840-847
Modification of microstructure and mechanical properties of Al–Zn–Mg/3 wt.% Al2O3 composite through semi-solid thermomechanical processing using variable loads
The microstructure and mechanical properties of Al–Zn–Mg/3 wt.% Al2O3 composite were modified through a thermomechanical processing technique. The powders were cold pressed and solid state sintered for 90 min under argon atmosphere. Thermomechanical processing was then applied to the solid state sintered samples, which consisted of cold pressing followed by partial remelting for 30 min under argon atmosphere. Four different loads in the thermomechanical processing were used to investigate the effects of compressive loads on the microstructures and the mechanical properties. The results revealed modifications in the microstructure of the thermomechanically processed samples with the optimum combination of properties in the sample modified by applying the load of 250 MPa. Increasing the thermomechanical processing load decreased the amounts of porosity by about 7 %, decreased the average grain size to about 4 μm, enhanced the compressive yield strength to about 295 MPa, and increased the microhardness values from 250 HV to 600 HV. In addition, the energy absorption capacity increased by about three times.
- 28 September 2017
- Published by Walter de Gruyter GmbH in International Journal of Materials Research
- Vol. 108 (10) , 840-847
Modification of microstructure and mechanical properties of Al–Zn–Mg/3 wt.% Al2O3 composite through semi-solid thermomechanical processing using variable loads
The microstructure and mechanical properties of Al–Zn–Mg/3 wt.% Al2O3 composite were modified through a thermomechanical processing technique. The powders were cold pressed and solid state sintered for 90 min under argon atmosphere. Thermomechanical processing was then applied to the solid state sintered samples, which consisted of cold pressing followed by partial remelting for 30 min under argon atmosphere. Four different loads in the thermomechanical processing were used to investigate the effects of compressive loads on the microstructures and the mechanical properties. The results revealed modifications in the microstructure of the thermomechanically processed samples with the optimum combination of properties in the sample modified by applying the load of 250 MPa. Increasing the thermomechanical processing load decreased the amounts of porosity by about 7 %, decreased the average grain size to about 4 μm, enhanced the compressive yield strength to about 295 MPa, and increased the microhardness values from 250 HV to 600 HV. In addition, the energy absorption capacity increased by about three times.
- 11 September 2017
- Published by Springer Nature in Journal of Failure Analysis and Prevention
- Vol. 17 (6) , 1139-1148
Corrosion Failure of the External Surface of Chlorinator’s Copper Pipes in a Water Disinfection Station
- 11 September 2017
- Published by Springer Nature in Journal of Failure Analysis and Prevention
- Vol. 17 (6) , 1139-1148
Corrosion Failure of the External Surface of Chlorinator’s Copper Pipes in a Water Disinfection Station
- 7 February 2017
- Published by Springer Nature in Metallurgical and Materials Transactions A
- Vol. 48 (4) , 1856-1863
A Study on Hot Tearing Behavior of Al-1 Wt Pct Cu Alloy Under Various Strain Rates During Casting Process
- 7 February 2017
- Published by Springer Nature in Metallurgical and Materials Transactions A
- Vol. 48 (4) , 1856-1863
A Study on Hot Tearing Behavior of Al-1 Wt Pct Cu Alloy Under Various Strain Rates During Casting Process
- 1 August 2016
- Published by Elsevier in Engineering Failure Analysis
- Vol. 66, 373-384
Interaction of hot corrosion and creep in Alloy 617
- 1 August 2016
- Published by Elsevier in Engineering Failure Analysis
- Vol. 66, 373-384
Interaction of hot corrosion and creep in Alloy 617