DRDavid Rodríguez-Rosa

David Rodríguez-Rosa

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


David Rodríguez-Rosa has a total of 50 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    A Simple and Economical 3-D Force Plate for Gait Analysis

    by Ismael Payo, Miguel Sánchez, Sergio Juárez, David Rodríguez, José García, Enrique Pérez

    3D force plates are used to measure the ground reaction forces/moments and the center of pressure (COP) during the stance phase of walking. Force plates consist of three essential components, i.e., lower platform, upper platform (typically with square or rectangular shape) and some load cells between both platforms. The design of the load cells, their location in the force plate and the type of sensors used in the load cells determine the main differences. Two types of sensors are usually used in load cells: resistive strain gauges and piezoelectric crystals. Commercial force plates usually have four 3D load cells located at the corners of the plate. The number of resistive strain gauges used commonly in each load cell of force plates based on resistive strain gauges is twenty-four, whereas piezoelectric force plates have three orthogonal piezoelectric sensors packaged in each load cell. Although the operational performance of commercial force plates is very good, they are very expensive, and many research groups cannot afford to buy them. A novel 3D force plate for gait analysis is proposed in this study with a simple design that is easy and economical compared to commercial force plates (approximately one-tenth of the cost of commercial force plates). The foot-ground reaction forces/moments and the COP are estimated from only eight force sensors strategically distributed on the force plate. Each force sensor consists of a uniaxial cantilever beam and a strain sensor attached at its fixed end. The design and manufacture of cantilever beam force sensors are simpler and more economical than 3D load cells used in commercial force plates. The cantilever beam force sensors are designed to maximize the signal-force relation and minimize vibration modes. The performance of the proposed force plate (linearity, ±1.6%FSO–Full Scale Output–, hysteresis ±0.5%FSO, accuracy error ±2%AL–Applied Load–, cross-talk ±5%AL, and COP accuracy error, 14.5 mm) has been compared with the performance of other commercial force plates. In general, the deviation of the specifications in our system is slightly greater than in commercial force plates. These deviations might be acceptable if we consider that we used manufacturing methods and machines which are not as precise as those used by companies that manufacture this type of force plate. In addition, two types of strain sensors, resistive strain gauges and piezoelectric paint sensors were compared in this study. Experimental tests showed similar results with both strain sensors. The relative mean difference in the estimation of the forces/moments with both strain sensors was lower than 5% in all cases except the vertical component of the force, Fy, which was about 9%, and the mean difference in the estimation of the COP with both sensors was 11 mm. Therefore, they might be used to design this type of force plate.


  • Open Access

    Vertical Balance of an Autonomous Two-Wheeled Single-Track Electric Vehicle

    by David Rodríguez-Rosa, Andrea Martín-Parra, Andrés García-Vanegas, Francisco Moya-Fernández, Ismael Payo-Gutiérrez, Fernando J. Castillo-García

    In the dynamic landscape of autonomous transport, the integration of intelligent transport systems and embedded control technology is pivotal. While strides have been made in the development of autonomous agents and multi-agent systems, the unique challenges posed by two-wheeled vehicles remain largely unaddressed. Dedicated control strategies for these vehicles have yet to be developed. The vertical balance of an autonomous two-wheeled single-track vehicle is a challenge for engineering. This type of vehicle is unstable and its dynamic behaviour changes with the forward velocity. We designed a scheduled-gain proportional–integral controller that adapts its gains to the forward velocity, maintaining the vertical balance of the vehicle by means of the steering front-wheel angle. The control law was tested with a prototype designed by the authors under different scenarios, smooth and uneven floors, maintaining the vertical balance in all cases.


  • Novel Position Control for Ensuring Feasible Tension Distribution of Cable-Driven Parallel Manipulators

    by Andrea Martín-Parra, Jorge Muñoz, Francisco Moya-Fernández, David Rodríguez-Rosa, Sergio Juárez-Pérez, Concepción A. Monje


  • Kinetostatic Analysis of a Novel Planar Cable-Driven Robot with a Single Cable Loop

    by Sergio Juárez-Pérez, Andrea Martín-Parra, Francisco Moya Fernández, David Rodríguez Rosa, Antonio Gónzalez Rodríguez

  • Open Access

    Deployment of Model-Based-Design-Adaptive Controllers for Monitoring and Control Mechatronic Devices

    by Ramon Barber, David R. Rosa, Antonio Flores-Caballero, Santiago Garrido

    The modeling and control of complex, non-linear, and time-changing mechatronic systems requires complex software development. They are carried out in the prototyping phase with engineering software development tools, generating models, and control algorithms that are not always easily exportable to control hardware. The following work offers an alternative that considers Model-Based Design using graphics-based languages, which facilitates programming tasks for modeling and controlling mechatronic devices and their transition from prototype to control hardware. Model-Based Design with high abstraction programming level capabilities provides the user with a fast coding and testing environment, suitable for laboratory prototyping and subsequent transfer to commercial embedded controllers. The proposed solution combines control hardware based on an STM32H7 microcontroller and a software development environment using graphics-based languages developed for MATLAB. The result is a solution that integrates control hardware and software in a hardware-in-the-loop paradigm. This solution provides robust and energy-saving controllers and demonstrates that an advanced control algorithm can be set up in a critical safety-compliant low-cost embedded controller via a custom model-based design. Algorithms and tools are transferred to the controller without losing the advantages gained in the prototyping phase. Finally, experimental results implementing an adaptive controller in a DC motor and in a pneumatic system are shown to validate the system.


  • Open Access

    Dynamic Model of a Novel Planar Cable Driven Parallel Robot with a Single Cable Loop

    by Antonio González-Rodríguez, Andrea Martín-Parra, Sergio Juárez-Pérez, David Rodríguez-Rosa, Francisco Moya-Fernández, Fernando J. Castillo-García, Jesús Rosado-Linares

    Cable-Driven Parallel Robots (CDPRs) are a special kind of parallel manipulator that uses cables to control the position and orientation of the mobile platform or end effector. The use of cables instead of rigid links offers some advantages over their conventional rigid counterparts. As cables can only pull but not push, the number of cables (n) required to command the end-effector is always n+1. This configuration is known as fully-constrained, and it is the most extended configuration for CDPRs. Although CDPRs have many advantages, such as their ability to cover large working areas, one of their main problems is that their working area (workspace) is limited in comparison to its frame area (planar case) or frame volume (spatial case), due to the minimum and maximum allowed tensions. Depending on these tension values, the workspace can notoriously decrease. In order to tackle this problem, lots of works focus on solving kinematics or dynamics problems for cable sagging, i.e., they take into account sagging when modelling the robot kinematic and include these poses inside the usable robot workspace. Taking into account phenomena such as this increases the mathematical complexity of the problem, and much more complex techniques are required. On the other hand, the lack of workspace problem can be tackled by adding active or passive elements to the robot design. In this sense, this paper proposes two mechanical modifications: to add passive carriages to the robot frame and to use a single cable loop to command the end-effector position and orientation. This work presents the kinematic, static, and dynamic models of the novel design and shows the gain of workspace for a planar case while taking into account different parameters of the robot.


  • Open Access

    Dynamic Model of a Novel Planar Cable Driven Parallel Robot with a Single Cable Loop

    by Antonio Gonzalez-Rodríguez, Andrea Martín-Parra, Sergio Juárez-Pérez, David Rodríguez-Rosa, Francisco Moya-Fernández, Fernando J. Castillo-García, Jesús Rosado

    Cable-Driven Parallel Robots (CDPRs) are a special kind of parallel manipulator which use cables to control the position and orientation of the mobile platform or end-effector. The usage of cables instead of rigid links offer some advantages over their conventional rigid counterparts. As cables can only pull, but not push, the number of cables (n) required to command the end-effector is always n+1. This configuration is known as fully-constrained and it is the most extended configuration for CDPRs. Although CDPRs have many advantages, such as their ability to cover large working areas, one of their main problems is that their working area (workspace) is limited in comparison to its frame area (planar case), or frame volume (spatial case), due to the minimum and maximum allowed tensions. Depending of these tensions values the workspace can be notoriously decreased. In order to tackle this problem, lots of works focus on solving kinematics or dynamics problems for cable sagging, i.e., they take into account sagging when modelling the robot kinematic and include these poses inside the usable robot workspace. Taking into account phenomenons like this increases the mathematical complexity of the problem, and much more complex techniques are required. On the other hand, the lack of workspace problem can be tackled by adding active or passive elements to the robot design. In this sense, this paper proposes two mechanical modifications: to add passive carriages to the robot frame and to use a single cable loop to command the end-effector position and orientation. This work presents the kinematic, static and dynamic models of the novel design and shows the gain of workspace for a planar case while taking into account different parameters of the robot.


  • Open Access

    Viability and Performance Analysis, at a Physical Level, of a Maritime Communication Network on Medium Frequency

    by Alfonso-Isidro López-Diaz, Miguel A. Gutiérrez, Andrés Ortega Piris, Emma Díaz-Ruiz-Navamuel, David Rodríguez-Rosa

    This paper analysed the potentialities that have not yet been exploited of the Automatic Vessel Identification System on Medium Frequency (AVISOMEF) that was previously presented to the scientific community. This system expanded the spectrum of possibilities of the Global Maritime Distress and Safety System (GMDSS). By the time AVISOMEF was presented, one of the unexpected benefits was that it could constitute a platform capable of supporting a Maritime Communication Network on Medium Frequency; all remotely located vessels could communicate with each other by using AVISOMEF, making use of the new established network, within the geographic area of implementation, without needing to use satellite techniques. Medium frequency propagation is stable and is not subject to coverage restrictions. To conduct this experiment, we collaborated with the Spanish Maritime Safety Agency (SASEMAR). It was thanks to them that we gathered real-time information about the nationwide maritime traffic that navigated through the Spanish Search and Rescue jurisdiction waters from 2018 to 2020.


  • Open Access

    New Sensor Device to Accurately Measure Cable Tension in Cable-Driven Parallel Robots

    by Guillermo Rubio-Gómez, Sergio Juárez-Pérez, Antonio Gonzalez-Rodríguez, David Rodríguez-Rosa, Lis Corral-Gómez, Alfonso I. López-Díaz, Ismael Payo, Fernando J. Castillo-García

    Cable-driven parallel robots are a special type of robot in which an end-effector is attached to a fixed frame by means of several cables. The position and orientation of the end-effector can be controlled by controlling the length of the cables. These robots present a wide range of advantages, and the control algorithms required have greater complexity than those in traditional serial robots. Measuring the cable tension is an important task in this type of robot as many control algorithms rely on this information. There are several well-known approaches to measure cable tension in cable robots, where a trade-off between complexity and accuracy is observed. This work presents a new device based on strain gauges to measure cable tension specially designed to be applied in cable-driven parallel robots. This device can be easily mounted on the cable near the fixed frame, allowing the cable length and orientation to change freely, while the measure is taken before the cable passes through the guiding pulleys for improved accuracy. The results obtained from the device show a strong repeatability and linearity of the measures