Sergio Juárez-Pérez
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Sergio Juárez-Pérez has a total of 28 co-authors. Here are the top co-authors by number of shared publications:
- David Rodríguez-Rosa
School of Industrial and Aerospace Engineering, University of Castilla-La Mancha, Av. Carlos III, 45071 Toledo, Spain
12 shared publications - Andrea Martín-Parra
University of Castilla-La Mancha
9 shared publications - Fernando Jose Castillo Garcia
University of Castilla-La Mancha
9 shared publications - Angel Gaspar Gonzalez-Rodriguez
Department of Electronic Engineering and Automation, University of Jaen, 23071 Jaén, Spain
8 shared publications - Francisco Moya
University of Castilla-La Mancha
6 shared publications - Guillermo Rubio-Gómez
Laboratory for Research and Innovation in Energy Technology (LIITE), Facultad de Ingeniería Mecánica y Eléctrica (FIME), Universidad Autónoma de Nuevo León, San Nicolás de los Garza, Mexico
4 shared publications
Latest Publications
- Open Access
- 16 October 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Instrumentation and Measurement
- Vol. 73 (00189456) , 1-10
A Simple and Economical 3-D Force Plate for Gait Analysis
3D force plates are used to measure the ground reaction forces/moments and the center of pressure (COP) during the stance phase of walking. Force plates consist of three essential components, i.e., lower platform, upper platform (typically with square or rectangular shape) and some load cells between both platforms. The design of the load cells, their location in the force plate and the type of sensors used in the load cells determine the main differences. Two types of sensors are usually used in load cells: resistive strain gauges and piezoelectric crystals. Commercial force plates usually have four 3D load cells located at the corners of the plate. The number of resistive strain gauges used commonly in each load cell of force plates based on resistive strain gauges is twenty-four, whereas piezoelectric force plates have three orthogonal piezoelectric sensors packaged in each load cell. Although the operational performance of commercial force plates is very good, they are very expensive, and many research groups cannot afford to buy them. A novel 3D force plate for gait analysis is proposed in this study with a simple design that is easy and economical compared to commercial force plates (approximately one-tenth of the cost of commercial force plates). The foot-ground reaction forces/moments and the COP are estimated from only eight force sensors strategically distributed on the force plate. Each force sensor consists of a uniaxial cantilever beam and a strain sensor attached at its fixed end. The design and manufacture of cantilever beam force sensors are simpler and more economical than 3D load cells used in commercial force plates. The cantilever beam force sensors are designed to maximize the signal-force relation and minimize vibration modes. The performance of the proposed force plate (linearity, ±1.6%FSO–Full Scale Output–, hysteresis ±0.5%FSO, accuracy error ±2%AL–Applied Load–, cross-talk ±5%AL, and COP accuracy error, 14.5 mm) has been compared with the performance of other commercial force plates. In general, the deviation of the specifications in our system is slightly greater than in commercial force plates. These deviations might be acceptable if we consider that we used manufacturing methods and machines which are not as precise as those used by companies that manufacture this type of force plate. In addition, two types of strain sensors, resistive strain gauges and piezoelectric paint sensors were compared in this study. Experimental tests showed similar results with both strain sensors. The relative mean difference in the estimation of the forces/moments with both strain sensors was lower than 5% in all cases except the vertical component of the force, Fy, which was about 9%, and the mean difference in the estimation of the COP with both sensors was 11 mm. Therefore, they might be used to design this type of force plate.
- 16 October 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Instrumentation and Measurement
- Vol. 73 (00189456) , 1-10
Open AccessA Simple and Economical 3-D Force Plate for Gait Analysis
3D force plates are used to measure the ground reaction forces/moments and the center of pressure (COP) during the stance phase of walking. Force plates consist of three essential components, i.e., lower platform, upper platform (typically with square or rectangular shape) and some load cells between both platforms. The design of the load cells, their location in the force plate and the type of sensors used in the load cells determine the main differences. Two types of sensors are usually used in load cells: resistive strain gauges and piezoelectric crystals. Commercial force plates usually have four 3D load cells located at the corners of the plate. The number of resistive strain gauges used commonly in each load cell of force plates based on resistive strain gauges is twenty-four, whereas piezoelectric force plates have three orthogonal piezoelectric sensors packaged in each load cell. Although the operational performance of commercial force plates is very good, they are very expensive, and many research groups cannot afford to buy them. A novel 3D force plate for gait analysis is proposed in this study with a simple design that is easy and economical compared to commercial force plates (approximately one-tenth of the cost of commercial force plates). The foot-ground reaction forces/moments and the COP are estimated from only eight force sensors strategically distributed on the force plate. Each force sensor consists of a uniaxial cantilever beam and a strain sensor attached at its fixed end. The design and manufacture of cantilever beam force sensors are simpler and more economical than 3D load cells used in commercial force plates. The cantilever beam force sensors are designed to maximize the signal-force relation and minimize vibration modes. The performance of the proposed force plate (linearity, ±1.6%FSO–Full Scale Output–, hysteresis ±0.5%FSO, accuracy error ±2%AL–Applied Load–, cross-talk ±5%AL, and COP accuracy error, 14.5 mm) has been compared with the performance of other commercial force plates. In general, the deviation of the specifications in our system is slightly greater than in commercial force plates. These deviations might be acceptable if we consider that we used manufacturing methods and machines which are not as precise as those used by companies that manufacture this type of force plate. In addition, two types of strain sensors, resistive strain gauges and piezoelectric paint sensors were compared in this study. Experimental tests showed similar results with both strain sensors. The relative mean difference in the estimation of the forces/moments with both strain sensors was lower than 5% in all cases except the vertical component of the force, Fy, which was about 9%, and the mean difference in the estimation of the COP with both sensors was 11 mm. Therefore, they might be used to design this type of force plate.
- 16 July 2024
- Published by Springer Nature
- p. 117-128
Novel Spatial Cable Driven Parallel Robot with Non-limited Workspace
- 16 July 2024
- Published by Springer Nature
- p. 117-128
Novel Spatial Cable Driven Parallel Robot with Non-limited Workspace
- 18 January 2024
- Published by Springer Nature
- p. 19-29
Novel Position Control for Ensuring Feasible Tension Distribution of Cable-Driven Parallel Manipulators
- 18 January 2024
- Published by Springer Nature
- p. 19-29
Novel Position Control for Ensuring Feasible Tension Distribution of Cable-Driven Parallel Manipulators
- 18 January 2024
- Published by Springer Nature
- p. 31-40
Kinetostatic Analysis of a Novel Planar Cable-Driven Robot with a Single Cable Loop
- 18 January 2024
- Published by Springer Nature
- p. 31-40
Kinetostatic Analysis of a Novel Planar Cable-Driven Robot with a Single Cable Loop
- Open Access
Dynamic Model of a Novel Planar Cable Driven Parallel Robot with a Single Cable Loop
Cable-Driven Parallel Robots (CDPRs) are a special kind of parallel manipulator that uses cables to control the position and orientation of the mobile platform or end effector. The use of cables instead of rigid links offers some advantages over their conventional rigid counterparts. As cables can only pull but not push, the number of cables (n) required to command the end-effector is always . This configuration is known as fully-constrained, and it is the most extended configuration for CDPRs. Although CDPRs have many advantages, such as their ability to cover large working areas, one of their main problems is that their working area (workspace) is limited in comparison to its frame area (planar case) or frame volume (spatial case), due to the minimum and maximum allowed tensions. Depending on these tension values, the workspace can notoriously decrease. In order to tackle this problem, lots of works focus on solving kinematics or dynamics problems for cable sagging, i.e., they take into account sagging when modelling the robot kinematic and include these poses inside the usable robot workspace. Taking into account phenomena such as this increases the mathematical complexity of the problem, and much more complex techniques are required. On the other hand, the lack of workspace problem can be tackled by adding active or passive elements to the robot design. In this sense, this paper proposes two mechanical modifications: to add passive carriages to the robot frame and to use a single cable loop to command the end-effector position and orientation. This work presents the kinematic, static, and dynamic models of the novel design and shows the gain of workspace for a planar case while taking into account different parameters of the robot.Open AccessDynamic Model of a Novel Planar Cable Driven Parallel Robot with a Single Cable Loop
Cable-Driven Parallel Robots (CDPRs) are a special kind of parallel manipulator that uses cables to control the position and orientation of the mobile platform or end effector. The use of cables instead of rigid links offers some advantages over their conventional rigid counterparts. As cables can only pull but not push, the number of cables (n) required to command the end-effector is always . This configuration is known as fully-constrained, and it is the most extended configuration for CDPRs. Although CDPRs have many advantages, such as their ability to cover large working areas, one of their main problems is that their working area (workspace) is limited in comparison to its frame area (planar case) or frame volume (spatial case), due to the minimum and maximum allowed tensions. Depending on these tension values, the workspace can notoriously decrease. In order to tackle this problem, lots of works focus on solving kinematics or dynamics problems for cable sagging, i.e., they take into account sagging when modelling the robot kinematic and include these poses inside the usable robot workspace. Taking into account phenomena such as this increases the mathematical complexity of the problem, and much more complex techniques are required. On the other hand, the lack of workspace problem can be tackled by adding active or passive elements to the robot design. In this sense, this paper proposes two mechanical modifications: to add passive carriages to the robot frame and to use a single cable loop to command the end-effector position and orientation. This work presents the kinematic, static, and dynamic models of the novel design and shows the gain of workspace for a planar case while taking into account different parameters of the robot. - Open Access
- 11 April 2023
- Published by MDPI AG in Preprints.org
Dynamic Model of a Novel Planar Cable Driven Parallel Robot with a Single Cable Loop
Cable-Driven Parallel Robots (CDPRs) are a special kind of parallel manipulator which use cables to control the position and orientation of the mobile platform or end-effector. The usage of cables instead of rigid links offer some advantages over their conventional rigid counterparts. As cables can only pull, but not push, the number of cables (n) required to command the end-effector is always n+1. This configuration is known as fully-constrained and it is the most extended configuration for CDPRs. Although CDPRs have many advantages, such as their ability to cover large working areas, one of their main problems is that their working area (workspace) is limited in comparison to its frame area (planar case), or frame volume (spatial case), due to the minimum and maximum allowed tensions. Depending of these tensions values the workspace can be notoriously decreased. In order to tackle this problem, lots of works focus on solving kinematics or dynamics problems for cable sagging, i.e., they take into account sagging when modelling the robot kinematic and include these poses inside the usable robot workspace. Taking into account phenomenons like this increases the mathematical complexity of the problem, and much more complex techniques are required. On the other hand, the lack of workspace problem can be tackled by adding active or passive elements to the robot design. In this sense, this paper proposes two mechanical modifications: to add passive carriages to the robot frame and to use a single cable loop to command the end-effector position and orientation. This work presents the kinematic, static and dynamic models of the novel design and shows the gain of workspace for a planar case while taking into account different parameters of the robot.
- 11 April 2023
- Published by MDPI AG in Preprints.org
Open AccessDynamic Model of a Novel Planar Cable Driven Parallel Robot with a Single Cable Loop
Cable-Driven Parallel Robots (CDPRs) are a special kind of parallel manipulator which use cables to control the position and orientation of the mobile platform or end-effector. The usage of cables instead of rigid links offer some advantages over their conventional rigid counterparts. As cables can only pull, but not push, the number of cables (n) required to command the end-effector is always n+1. This configuration is known as fully-constrained and it is the most extended configuration for CDPRs. Although CDPRs have many advantages, such as their ability to cover large working areas, one of their main problems is that their working area (workspace) is limited in comparison to its frame area (planar case), or frame volume (spatial case), due to the minimum and maximum allowed tensions. Depending of these tensions values the workspace can be notoriously decreased. In order to tackle this problem, lots of works focus on solving kinematics or dynamics problems for cable sagging, i.e., they take into account sagging when modelling the robot kinematic and include these poses inside the usable robot workspace. Taking into account phenomenons like this increases the mathematical complexity of the problem, and much more complex techniques are required. On the other hand, the lack of workspace problem can be tackled by adding active or passive elements to the robot design. In this sense, this paper proposes two mechanical modifications: to add passive carriages to the robot frame and to use a single cable loop to command the end-effector position and orientation. This work presents the kinematic, static and dynamic models of the novel design and shows the gain of workspace for a planar case while taking into account different parameters of the robot.
- Open Access
Dynamic Control of a Novel Planar Cable-Driven Parallel Robot with a Large Wrench Feasible Workspace
Cable-Driven Parallel Robots (CDPRs) are special manipulators where rigid links are replaced with cables. The use of cables offers several advantages over the conventional rigid manipulators, one of the most interesting being their ability to cover large workspaces since cables are easily winded. However, this workspace coverage has its limitations due to the maximum permissible cable tensions, i.e., tension limitations cause a decrease in the Wrench Feasible Workspace (WFW) of these robots. To solve this issue, a novel design based in the addition of passive carriages to the robot frame of three degrees-of-freedom (3DOF) fully-constrained CDPRs is used. The novelty of the design allows reducing the variation in the cable directions and forces increasing the robot WFW; nevertheless, it presents a low stiffness along the x direction. This paper presents the dynamic model of the novel proposal together with a new dynamic control technique, which rejects the vibrations caused by the stiffness loss while ensuring an accurate trajectory tracking. The simulation results show that the controlled system presents a larger WFW than the conventional scheme of the CDPR, maintaining a good performance in the trajectory tracking of the end-effector. The novel proposal presented here can be applied in multiple planar applications.
Open AccessDynamic Control of a Novel Planar Cable-Driven Parallel Robot with a Large Wrench Feasible Workspace
Cable-Driven Parallel Robots (CDPRs) are special manipulators where rigid links are replaced with cables. The use of cables offers several advantages over the conventional rigid manipulators, one of the most interesting being their ability to cover large workspaces since cables are easily winded. However, this workspace coverage has its limitations due to the maximum permissible cable tensions, i.e., tension limitations cause a decrease in the Wrench Feasible Workspace (WFW) of these robots. To solve this issue, a novel design based in the addition of passive carriages to the robot frame of three degrees-of-freedom (3DOF) fully-constrained CDPRs is used. The novelty of the design allows reducing the variation in the cable directions and forces increasing the robot WFW; nevertheless, it presents a low stiffness along the x direction. This paper presents the dynamic model of the novel proposal together with a new dynamic control technique, which rejects the vibrations caused by the stiffness loss while ensuring an accurate trajectory tracking. The simulation results show that the controlled system presents a larger WFW than the conventional scheme of the CDPR, maintaining a good performance in the trajectory tracking of the end-effector. The novel proposal presented here can be applied in multiple planar applications.
- 22 November 2022
- Published by Elsevier in Mechanism and Machine Theory
- Vol. 180
A novel design for fully constrained planar Cable-Driven Parallel Robots to increase their wrench-feasible workspace
- 22 November 2022
- Published by Elsevier in Mechanism and Machine Theory
- Vol. 180
A novel design for fully constrained planar Cable-Driven Parallel Robots to increase their wrench-feasible workspace
- 30 July 2022
- Published by Elsevier in Measurement
- Vol. 201
Voltage drift compensation in charge amplifiers for DC measurements: Application to piezoelectric paint sensors
- 30 July 2022
- Published by Elsevier in Measurement
- Vol. 201
Voltage drift compensation in charge amplifiers for DC measurements: Application to piezoelectric paint sensors
- Open Access
New Sensor Device to Accurately Measure Cable Tension in Cable-Driven Parallel Robots
Cable-driven parallel robots are a special type of robot in which an end-effector is attached to a fixed frame by means of several cables. The position and orientation of the end-effector can be controlled by controlling the length of the cables. These robots present a wide range of advantages, and the control algorithms required have greater complexity than those in traditional serial robots. Measuring the cable tension is an important task in this type of robot as many control algorithms rely on this information. There are several well-known approaches to measure cable tension in cable robots, where a trade-off between complexity and accuracy is observed. This work presents a new device based on strain gauges to measure cable tension specially designed to be applied in cable-driven parallel robots. This device can be easily mounted on the cable near the fixed frame, allowing the cable length and orientation to change freely, while the measure is taken before the cable passes through the guiding pulleys for improved accuracy. The results obtained from the device show a strong repeatability and linearity of the measures
Open AccessNew Sensor Device to Accurately Measure Cable Tension in Cable-Driven Parallel Robots
Cable-driven parallel robots are a special type of robot in which an end-effector is attached to a fixed frame by means of several cables. The position and orientation of the end-effector can be controlled by controlling the length of the cables. These robots present a wide range of advantages, and the control algorithms required have greater complexity than those in traditional serial robots. Measuring the cable tension is an important task in this type of robot as many control algorithms rely on this information. There are several well-known approaches to measure cable tension in cable robots, where a trade-off between complexity and accuracy is observed. This work presents a new device based on strain gauges to measure cable tension specially designed to be applied in cable-driven parallel robots. This device can be easily mounted on the cable near the fixed frame, allowing the cable length and orientation to change freely, while the measure is taken before the cable passes through the guiding pulleys for improved accuracy. The results obtained from the device show a strong repeatability and linearity of the measures