Alexander Bonk
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Alexander Bonk has a total of 55 co-authors. Here are the top co-authors by number of shared publications:
- Thomas Bauer
Institute of Engineering Thermodynamics, German Aerospace Center (DLR), Linder Höhe, D-51147 Cologne, Germany
14 shared publications Andrea Hanke
German Aerospace Center (DLR), Institute of Engineering Thermodynamics, 70569, Stuttgart, Germany
7 shared publicationsMarkus Braun
6 shared publications- Wenjin Ding
Institute of Engineering Thermodynamics, German Aerospace Center (DLR), D-70569 Stuttgart, Germany
4 shared publications - Markus Braun
German Aerospace Center (DLR), Institute of Engineering Thermodynamics, D-70569 Stuttgart, Germany
3 shared publications - Sumit Kumar
Institute of Engineering Thermodynamics German Aerospace Center (DLR) Stuttgart Baden‐Württemberg Germany
3 shared publications
Latest Publications
- Open Access
- 11 March 2025
- Published by Elsevier in Corrosion Science
- Vol. 249
Understanding the effect of oxide ions on Solar Salt chemistry and corrosion mechanism of 316 L stainless steel at 600 °C
- 11 March 2025
- Published by Elsevier in Corrosion Science
- Vol. 249
Open AccessUnderstanding the effect of oxide ions on Solar Salt chemistry and corrosion mechanism of 316 L stainless steel at 600 °C
- Open Access
- 16 January 2024
- Published by TIB Open Publishing in SolarPACES Conference Proceedings
- Vol. 1
Operating Parabolic Troughs With Molten Salt: Solar Field Optimisation and Ternary Salt Properties
A variety of works have been performed at the Évora Molten Salt Platform on a new collector system especially designed for optimised operation with solar salt as well as tests on a ternary salt. Concerning the new HelioTrough® 3.1 design the paper discusses how 30% less specific mass could be reached. Together with a novel approach to “run-in” bearings, as to lower friction, the torsion could be reduced significantly. Resultingly costs were reduced while improving precision of the trough. The ternary salt has been operated between October 2021 and May 2022 in the end reaching operation temperatures up to 500°C. Samples have been taken and analysed to investigate nitrite and nitrate development amongst others. The heat capacity of the Yara Molten Salt has been determined with now a high level of precision, as well as the density.
- 16 January 2024
- Published by TIB Open Publishing in SolarPACES Conference Proceedings
- Vol. 1
Open AccessOperating Parabolic Troughs With Molten Salt: Solar Field Optimisation and Ternary Salt Properties
A variety of works have been performed at the Évora Molten Salt Platform on a new collector system especially designed for optimised operation with solar salt as well as tests on a ternary salt. Concerning the new HelioTrough® 3.1 design the paper discusses how 30% less specific mass could be reached. Together with a novel approach to “run-in” bearings, as to lower friction, the torsion could be reduced significantly. Resultingly costs were reduced while improving precision of the trough. The ternary salt has been operated between October 2021 and May 2022 in the end reaching operation temperatures up to 500°C. Samples have been taken and analysed to investigate nitrite and nitrate development amongst others. The heat capacity of the Yara Molten Salt has been determined with now a high level of precision, as well as the density.
- Open Access
Demonstration of the stabilization of solar salt at 620 C with a semi-closed configuration in a 100 kg-scale
- 22 November 2023
- Published by Elsevier in Corrosion Science
- Vol. 227
Effect of gas management on corrosion resistance in molten solar salt up to 620 °C: Corrosion of SS316-types and SS347
- 22 November 2023
- Published by Elsevier in Corrosion Science
- Vol. 227
Effect of gas management on corrosion resistance in molten solar salt up to 620 °C: Corrosion of SS316-types and SS347
- Open Access
AlCl3-NaCl-ZnCl2 Secondary Electrolyte in Next-Generation ZEBRA (Na-ZnCl2) Battery
Increasing demand to store intermittent renewable electricity from, e.g., photovoltaic and wind energy, has led to much research and development in large-scale stationary energy storage, for example, ZEBRA batteries (Na-NiCl2 solid electrolyte batteries). Replacing Ni with abundant and low-cost Zn makes the ZEBRA battery more cost-effective. However, few studies were performed on this next-generation ZEBRA (Na-ZnCl2) battery system, particularly on its AlCl3-NaCl-ZnCl2 secondary electrolyte. Its properties such as phase diagrams and vapor pressures are vital for the cell design and optimization. In our previous work, a simulation-assisted method for molten salt electrolyte selection has shown its successful application in development of molten salt batteries. The same method is used here to in-depth study the AlCl3-NaCl-ZnCl2 salt electrolyte in terms of its phase diagrams and vapor pressures via FactSageTM and thermo-analytical techniques (Differential Scanning Calorimetry (DSC) and OptiMeltTM), and their effects on battery performance such as operation safety and charging/discharging reaction mechanism. The DSC and OptiMelt results show that the experimental data such as melting temperatures and phase changes agree well with the simulated phase diagrams. Moreover, the FactSageTM simulation shows that the salt vapor pressure increases significantly with increasing temperature and molar fraction of AlCl3. The obtained phase diagrams and vapor pressures will be used in the secondary electrolyte selection, cell design and battery operation.
Open AccessAlCl3-NaCl-ZnCl2 Secondary Electrolyte in Next-Generation ZEBRA (Na-ZnCl2) Battery
Increasing demand to store intermittent renewable electricity from, e.g., photovoltaic and wind energy, has led to much research and development in large-scale stationary energy storage, for example, ZEBRA batteries (Na-NiCl2 solid electrolyte batteries). Replacing Ni with abundant and low-cost Zn makes the ZEBRA battery more cost-effective. However, few studies were performed on this next-generation ZEBRA (Na-ZnCl2) battery system, particularly on its AlCl3-NaCl-ZnCl2 secondary electrolyte. Its properties such as phase diagrams and vapor pressures are vital for the cell design and optimization. In our previous work, a simulation-assisted method for molten salt electrolyte selection has shown its successful application in development of molten salt batteries. The same method is used here to in-depth study the AlCl3-NaCl-ZnCl2 salt electrolyte in terms of its phase diagrams and vapor pressures via FactSageTM and thermo-analytical techniques (Differential Scanning Calorimetry (DSC) and OptiMeltTM), and their effects on battery performance such as operation safety and charging/discharging reaction mechanism. The DSC and OptiMelt results show that the experimental data such as melting temperatures and phase changes agree well with the simulated phase diagrams. Moreover, the FactSageTM simulation shows that the salt vapor pressure increases significantly with increasing temperature and molar fraction of AlCl3. The obtained phase diagrams and vapor pressures will be used in the secondary electrolyte selection, cell design and battery operation.
- Open Access
Solar Salt above 600 °C: Impact of Experimental Design on Thermodynamic Stability Results
Thermal energy storage (TES) based on molten salts has been identified as a key player in the transition from fossil fuels to renewable energy sources. Solar Salt, a mixture of NaNO3 (60 wt%) and KNO3 (40 wt%), is currently the most advanced heat transfer and storage material used in concentrating solar power (CSP) plants. Here, it is utilized to produce electricity via a Rankine cycle, with steam temperatures reaching 550 °C. The goal of this study is to increase the operating temperature of solar salt to over 600 °C, allowing it to be adapted for use in high-temperature Rankine cycles with steam temperatures greater than 600 °C. Yet, this goal is impaired by the lack of available thermodynamic data given the salt’s complex high-temperature decomposition and corrosion chemistry. The study explores the thermodynamics of the decomposition reactions in solar salt, with a focus on suppressing decomposition into corrosive oxide ions up to a temperature of 620 °C. The results provide a new understanding of the stabilization of solar salt at previously unexplored temperatures with effective utilization of gas management techniques.
Open AccessSolar Salt above 600 °C: Impact of Experimental Design on Thermodynamic Stability Results
Thermal energy storage (TES) based on molten salts has been identified as a key player in the transition from fossil fuels to renewable energy sources. Solar Salt, a mixture of NaNO3 (60 wt%) and KNO3 (40 wt%), is currently the most advanced heat transfer and storage material used in concentrating solar power (CSP) plants. Here, it is utilized to produce electricity via a Rankine cycle, with steam temperatures reaching 550 °C. The goal of this study is to increase the operating temperature of solar salt to over 600 °C, allowing it to be adapted for use in high-temperature Rankine cycles with steam temperatures greater than 600 °C. Yet, this goal is impaired by the lack of available thermodynamic data given the salt’s complex high-temperature decomposition and corrosion chemistry. The study explores the thermodynamics of the decomposition reactions in solar salt, with a focus on suppressing decomposition into corrosive oxide ions up to a temperature of 620 °C. The results provide a new understanding of the stabilization of solar salt at previously unexplored temperatures with effective utilization of gas management techniques.
- Open Access
- 22 January 2022
- Published by Wiley in Advanced Engineering Materials
- Vol. 24 (7) , 2101453
Synthetic Biofuels by Molten‐Salt Catalytic Conversion: Corrosion of Structural Materials in Ternary Molten Chlorides
The molten‐salt catalytic conversion of biomass into synthetic fuels is one of the promising renewable energy topics of the 21st century. Mixtures of Zn–Na–K//Cl have gained attention, acting as catalytically active heat transfer fluids in the conversion process, due to their low costs and principally low melting points which effectively lower the required operating temperature in the catalytic reactor. Herein, the corrosion behavior of three candidate steels, SS316L, SS321, and Alloy 800, in the pure molten salt, in a salt–biomass mix, and in a salt–biomass mix containing a corrosion inhibitor (zinc oxide (ZnO)) is comprehensively investigated. The herein described study demonstrates that biomass additions increase the penetration depth of the salt, and the corrosion mechanism leads to partial spalling of the oxide scale. This is attributed to the presence of oxygen and moisture from the biomass leading to the formation of reactive HCl gas. The addition of ZnO reduced the corrosivity of the molten salt–biomass mix, and all alloys obtained a protective, adherent, and thin oxide scale leading to the conclusion that ZnO indeed is an effective corrosion inhibitor for the presented salt system. These findings constitute a major advance in the implementation of molten salt‐catalytic reactors for renewable synthetic fuel production.
- 22 January 2022
- Published by Wiley in Advanced Engineering Materials
- Vol. 24 (7) , 2101453
Open AccessSynthetic Biofuels by Molten‐Salt Catalytic Conversion: Corrosion of Structural Materials in Ternary Molten Chlorides
The molten‐salt catalytic conversion of biomass into synthetic fuels is one of the promising renewable energy topics of the 21st century. Mixtures of Zn–Na–K//Cl have gained attention, acting as catalytically active heat transfer fluids in the conversion process, due to their low costs and principally low melting points which effectively lower the required operating temperature in the catalytic reactor. Herein, the corrosion behavior of three candidate steels, SS316L, SS321, and Alloy 800, in the pure molten salt, in a salt–biomass mix, and in a salt–biomass mix containing a corrosion inhibitor (zinc oxide (ZnO)) is comprehensively investigated. The herein described study demonstrates that biomass additions increase the penetration depth of the salt, and the corrosion mechanism leads to partial spalling of the oxide scale. This is attributed to the presence of oxygen and moisture from the biomass leading to the formation of reactive HCl gas. The addition of ZnO reduced the corrosivity of the molten salt–biomass mix, and all alloys obtained a protective, adherent, and thin oxide scale leading to the conclusion that ZnO indeed is an effective corrosion inhibitor for the presented salt system. These findings constitute a major advance in the implementation of molten salt‐catalytic reactors for renewable synthetic fuel production.
- 1 January 2022
- Published by Elsevier in Solar Energy
- Vol. 231, 1061-1071
Phase diagram, thermodynamic properties and long-term isothermal stability of quaternary molten nitrate salts for thermal energy storage
- 1 January 2022
- Published by Elsevier in Solar Energy
- Vol. 231, 1061-1071
Phase diagram, thermodynamic properties and long-term isothermal stability of quaternary molten nitrate salts for thermal energy storage