VPVelumani Periasamy

Velumani Periasamy

*This is an algorithmically generated author record based on publicly available information.

Velumani Periasamy has a total of 6 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Performance ability study on sludge contained hollow concrete blocks

    by Velumani Periasamy, Aruna Govindan

    Generation of waste from the consumption of human society at the global level is an increment level day by day. The daily life requirements of the human society start from water consumption, clothes, vehicles for travel, power consumption, drugs etc. The utilization of these facilities by the public leads to different pollution and also generation of waste in different forms. The disposal of the generated waste poses a threat to the human society which needs more attention in the present scenario. Also, utilization of waste results in a sustainability by reducing their environmental footprints and conserving resources. In this article, the sludge generated from the textile industry effluents after its treatment and hypo sludge a waste generated from paper industry were taken for the experimental study. The physico chemical characteristics were analyzed and an attempt was made to utilize the sludge to replace cement in the manufacturing of hollow concrete blocks. The hollow concrete blocks were cast and tested as per the recommendations of BIS standards. The experimental study reveals that about 10% of cement can be replaced effectively for the manufacturing of hollow concrete blocks and possible standards are achieved.

  • Open Access

    Axial compression behavior of edge stiffened C-profile aluminium alloy: a finite element analysis

    by Velumani Periasamy, Aruna Govindan, Saravanan Ramasamy

    Aluminium alloys find diverse applications in building construction. Specifically, C-profiles being used as various structural elements in the building. Providing Edge stiffeners in the C-profile leads to increase the load carrying capacity. Limited research is available on compression behaviour c-profile with edge stiffeners. Hence, this article aims to study the behaviour of a Finite Element Analysis of aluminium alloy stiffened edge C profiles subjected to axial compression. Two different aluminium alloy materials, namely 6061-T6, and 6063-T5 were investigated. Finite element models were developed and results, including ultimate load, failure modes, and load vs. axial shortening curves, were verified against existing test data. A comprehensive parametric study was carried out based on the verified finite element models, involving variation in the orientation of the edge stiffener, column length, and section thickness. A total of 144 parametric results were compared with the design strengths calculated from Euro code 9.


  • Production of sludge-incorporated paver blocks for efficient waste management

    by P. Velumani, S. Senthilkumar

    Waste management plays a vital role in the reuse of industry wastes in to useful conversions. The treatment of effluents from the combined textile effluent treatment plant and hypo sludge from the paper industry results in sludge generation, which poses a huge challenge for its disposal. Therefore, an eco-friendly attempt is made to utilize them in the production of paver blocks. Paver blocks are construction units that have vast applications in street roads, walking paths, fuel stations, and so on. In this study, an innovative attempt has been made to manufacture paver blocks incorporating textile effluent treatment plant sludge and hypo sludge, to utilize them in suitable proportions. The effect of adding silica fume and polypropylene fibre in paver blocks has also been studied. Paver blocks containing sludge with different proportions were cast based on the recommendations in Indian Standards (IS) 15658, and the test results were compared with the nominal M20 grade and M30 grade paver blocks. The outcomes of the paver block combinations were studied and found to be an effective utilization of sludge with substantial cement replacement of up to 35%, resulting in effective waste management for specific industries. Implications: Presently, paver blocks are construction units that have vast application in street roads and other constructions like walking paths, fuel stations, and so on. Also, paver blocks possess easy maintenance during breakages. Based on this application, an innovative attempt has been made to manufacture paver blocks incorporating textile effluent treatment plant sludge and hypo sludge to utilize them in suitable proportions.


  • An Innovative Approach to Evaluate the Performance of Sludge-Incorporated Fly Ash Bricks

    by P. Velumani, S. SenthilKumar, P. V. Premalatha

    The Industrial Revolution turned a new leaf in the economic growth of India, which is famous for its industries and agriculture. Notably, the textile industry, which is one of the major sectors, has had rapid growth throughout India in general and Tamil Nadu in particular. The government of India has earmarked seven hundred crore rupees in its twelfth five-year plan during 2012–2017 for the development of textiles to increase production at a large scale. For the largest production operations, the necessity arises for the treatment of effluents to be carried out jointly by companies or as individual industries. Apparently, the treatment of textile effluents generates sludge in bulk quantities. This poses a challenge for its disposal. So, attempts were taken to use the sludge as an affordable construction material. Sludge was collected from the effluent treatment plants of the textile industries located in the State Industries Promotion Corporation of Tamil Nadu (SIPCOT), Perundurai, which is popularly known as a commercial hub. To make a brick, materials like hypo sludge, textile sludge, quarry dust, fly ash, and gypsum were added in suitable proportion. The manufacture of bricks was done in accordance with Indian standard practice. Not only observations but also evaluations were made correctly. There was an increase in strength, which satisfied the criteria of durability, as hypo sludge content was increased. All the combinations that were formulated for the production of brick satisfy Bureau of Indian Standards (BIS) requirements.