Raju Prasad Mahto
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Raju Prasad Mahto has a total of 52 co-authors. Here are the top co-authors by number of shared publications:
Surjya K. Pal
6 shared publications- Krishna Kishore Mugada
Department of Mechanical Engineering, Sardar Vallabhbhai National Institute of Technology Surat, Surat, India
4 shared publications - Gaurav Kishor
Department of Mechanical Engineering, Sardar Vallabhbhai National Institute of Technology Surat, Surat, India
3 shared publications Srikanta Pal
Birla Institute of Technology Mesra
3 shared publicationsSurjya Kanta Pal
3 shared publicationsAaquib Reza Khan
2 shared publications
Latest Publications
- 12 October 2026
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part L: Journal of Materials: Design and Applications
Air-induced laser-assisted sequential micro-milling process for precise microchannel fabrication
Laser micromilling suffers from surface oxidation and spatter surrounding the machined zone. However, the micromilling process has drawbacks, including tool wear, high cutting forces, burr formation, and reduced tool life. To address these issues, this study proposes a novel hybrid method for fabricating 100 µm microchannels through an air-induced laser-assisted sequential micromilling (AILASMM) process, comprising laser milling followed by tool-based micromilling. To mitigate cutting forces, compressed air is introduced during laser machining to assist in effective material removal and to promote the formation of an oxidation layer, thereby reducing forces during the subsequent micromilling step. Results demonstrated that AILASMM significantly reduces (15–25%) the magnitude of the cutting forces with respect to conventional micromilling (CMM). In addition to that, the tool wear and burr formation were reduced (15–25%) in the former technique and produced a better surface finish. Milling at an increased feed rate increased the cutting forces. The burr size was also observed to increase (from 37 to 59 µm) as the feed rate increased (from 40 to 60 mm/min). AILASMM at a lower value of the spindle speed (20000 rpm), the surface finish improved to 0.6 µm, and the burr size was reduced to 20 µm. AILASMM produced small and fragmented chips, significantly reducing the tool's adhesion wear.
- 12 October 2026
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part L: Journal of Materials: Design and Applications
Air-induced laser-assisted sequential micro-milling process for precise microchannel fabrication
Laser micromilling suffers from surface oxidation and spatter surrounding the machined zone. However, the micromilling process has drawbacks, including tool wear, high cutting forces, burr formation, and reduced tool life. To address these issues, this study proposes a novel hybrid method for fabricating 100 µm microchannels through an air-induced laser-assisted sequential micromilling (AILASMM) process, comprising laser milling followed by tool-based micromilling. To mitigate cutting forces, compressed air is introduced during laser machining to assist in effective material removal and to promote the formation of an oxidation layer, thereby reducing forces during the subsequent micromilling step. Results demonstrated that AILASMM significantly reduces (15–25%) the magnitude of the cutting forces with respect to conventional micromilling (CMM). In addition to that, the tool wear and burr formation were reduced (15–25%) in the former technique and produced a better surface finish. Milling at an increased feed rate increased the cutting forces. The burr size was also observed to increase (from 37 to 59 µm) as the feed rate increased (from 40 to 60 mm/min). AILASMM at a lower value of the spindle speed (20000 rpm), the surface finish improved to 0.6 µm, and the burr size was reduced to 20 µm. AILASMM produced small and fragmented chips, significantly reducing the tool's adhesion wear.
- 3 February 2026
- Published by Springer Nature in Progress in Additive Manufacturing
- Vol. 11 (4) , 3485-3521
A review on in-situ monitoring, process control and residual stress prediction using machine learning methods in metal-based laser additive manufacturing
- 3 February 2026
- Published by Springer Nature in Progress in Additive Manufacturing
- Vol. 11 (4) , 3485-3521
A review on in-situ monitoring, process control and residual stress prediction using machine learning methods in metal-based laser additive manufacturing
- 21 June 2025
- Published by Springer Nature in Metals and Materials International
- Vol. 32 (1) , 50-80
Wire Arc Additive Manufacturing of Titanium Alloys for Enhancing Mechanical Properties and Grain-Refinement
- 21 June 2025
- Published by Springer Nature in Metals and Materials International
- Vol. 32 (1) , 50-80
Wire Arc Additive Manufacturing of Titanium Alloys for Enhancing Mechanical Properties and Grain-Refinement
- 29 April 2025
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 138 (3-4) , 1197-1219
A study on build quality of friction stir deposition–based additive manufacturing: mechanical properties and defects
- 29 April 2025
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 138 (3-4) , 1197-1219
A study on build quality of friction stir deposition–based additive manufacturing: mechanical properties and defects
- 13 February 2025
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 34 (19) , 22193-22206
Microstructure, Mechanical, and Tribological Behavior of Al-5%Si Thin Wall Fabricated through Wire Arc Additive Manufacturing
- 13 February 2025
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 34 (19) , 22193-22206
Microstructure, Mechanical, and Tribological Behavior of Al-5%Si Thin Wall Fabricated through Wire Arc Additive Manufacturing
- 2 December 2024
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 34 (10) , 8817-8834
Deposition Strategy on Microstructure Development and Mechanical Properties of Wire Arc Additively Manufactured Austenitic Stainless Steel
- 2 December 2024
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 34 (10) , 8817-8834
Deposition Strategy on Microstructure Development and Mechanical Properties of Wire Arc Additively Manufactured Austenitic Stainless Steel
- 24 May 2019
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 104 (1-4) , 159-177
Monitoring of friction stir welding for dissimilar Al 6063 alloy to polypropylene using sensor signals
- 24 May 2019
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 104 (1-4) , 159-177
Monitoring of friction stir welding for dissimilar Al 6063 alloy to polypropylene using sensor signals
- 14 February 2019
- Published by Springer Nature
- p. 101-109
A Review and Case Study on Mechanical Properties and Microstructure Evolution in Magnesium–Steel Friction Stir Welding
- 14 February 2019
- Published by Springer Nature
- p. 101-109
A Review and Case Study on Mechanical Properties and Microstructure Evolution in Magnesium–Steel Friction Stir Welding