P G D C K Karunarathna
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
P G D C K Karunarathna has a total of 9 co-authors. Here are the top co-authors by number of shared publications:
- Chakrawarthige A. N. Fernando
Department of Nano Science Technology, Wayamba University of Sri Lanka, Faculty of Applied Sciences, Wayamba University of Sri Lanka, Kuliyapitiya, North Western, 60200, SRI LANKA
6 shared publications - S P A U K Samarakoon
Department of Nano Science Technology, Faculty of Technology, Wayamba University of Sri Lanka, Kuliyapitiya, Sri Lanka
4 shared publications - Pubudu Samarasekara
University of Peradeniya, Peradeniya
2 shared publications B M C M Bandaranayake
Univ Peradeniya, Dept Phys, Peradeniya, Sri Lanka
1 shared publicationH P Weeramuni
1 shared publicationJayashani Subhashini Theresa Wickramasinghe
Physics, University of Peradeniya Faculty of Science, Peradeniya, Central, SRI LANKA
1 shared publication
Latest Publications
- 11 December 2018
- Published by IOP Publishing in Materials Research Express
- Vol. 6 (3) , 036415
Spin coated multilayered CuO/ZnO films with high output power under irradiation
Thin films of pure CuO, pure ZnO and CuO/ZnO multilayers were synthesized using spin coating technique. CuO and ZnO layers were spin coated for 30 s at speeds of 2000 and 1500 rpm, respectively. All the samples were subsequently annealed at 500 0C for one hour in air. Structural properties of films investigated using XRD patterns indicated the crystallization of single phase of CuO and ZnO. Optical band gaps of samples determined by UV-visible spectrums were in the range of the band gaps of CuO and ZnO. The main objective of the preparation of multilayered CuO/ZnO was enhancing the output power by combining wide band gap and narrow band gap materials. CuO with higher photocurrent and ZnO with higher photovoltage were employed to achieve this task. Photocurrent, photovoltage and impedance were measured in order to investigate electrical properties of samples. A liquid junction photocell with electrolyte KI was employed to measure photovoltaic properties. Multilayer with ZnO as the top layer provides a higher output power of 3.6088 µW/cm2 compared to the output power of multilayer with CuO as the top layer (1.101 µW/cm2). This is the highest output power reported for a multilayer of CuO/ZnO without any dye coating in KI electrolyte. The highest output power of our multilayered samples is more than twice the previously reported highest output powers of pure CuO and pure ZnO thin film samples without dye coating. Structural properties of samples were confirmed by FTIR. Crystallite size was in the range from 23.41 to 28.51 nm. Impedance curves of all the samples were measured under dark and light conditions. Two semicircles could be observed at Nyquist plots of both multilayer samples.
- 11 December 2018
- Published by IOP Publishing in Materials Research Express
- Vol. 6 (3) , 036415
Spin coated multilayered CuO/ZnO films with high output power under irradiation
Thin films of pure CuO, pure ZnO and CuO/ZnO multilayers were synthesized using spin coating technique. CuO and ZnO layers were spin coated for 30 s at speeds of 2000 and 1500 rpm, respectively. All the samples were subsequently annealed at 500 0C for one hour in air. Structural properties of films investigated using XRD patterns indicated the crystallization of single phase of CuO and ZnO. Optical band gaps of samples determined by UV-visible spectrums were in the range of the band gaps of CuO and ZnO. The main objective of the preparation of multilayered CuO/ZnO was enhancing the output power by combining wide band gap and narrow band gap materials. CuO with higher photocurrent and ZnO with higher photovoltage were employed to achieve this task. Photocurrent, photovoltage and impedance were measured in order to investigate electrical properties of samples. A liquid junction photocell with electrolyte KI was employed to measure photovoltaic properties. Multilayer with ZnO as the top layer provides a higher output power of 3.6088 µW/cm2 compared to the output power of multilayer with CuO as the top layer (1.101 µW/cm2). This is the highest output power reported for a multilayer of CuO/ZnO without any dye coating in KI electrolyte. The highest output power of our multilayered samples is more than twice the previously reported highest output powers of pure CuO and pure ZnO thin film samples without dye coating. Structural properties of samples were confirmed by FTIR. Crystallite size was in the range from 23.41 to 28.51 nm. Impedance curves of all the samples were measured under dark and light conditions. Two semicircles could be observed at Nyquist plots of both multilayer samples.
- 1 June 2018
- Published by IOP Publishing in Materials Research Express
- Vol. 5 (6) , 065052
Characterization of Fe doped n-CuSCN/p-Cu2S solid-state photovoltaic cell
- 1 June 2018
- Published by IOP Publishing in Materials Research Express
- Vol. 5 (6) , 065052
Characterization of Fe doped n-CuSCN/p-Cu2S solid-state photovoltaic cell
- 1 June 2018
- Published by IOP Publishing in Materials Research Express
- Vol. 5 (6) , 066418
Electrical properties of spin coated Zn doped CuO films
- 1 June 2018
- Published by IOP Publishing in Materials Research Express
- Vol. 5 (6) , 066418
Electrical properties of spin coated Zn doped CuO films
- 14 November 2017
- Published by IOP Publishing in Materials Research Express
- Vol. 5 (1) , 015005
Explanation of the photocurrent generation of Cu2O quantum dots (QDs) sensitized p-CuSCN stable photoelectrochemical cells
Fabrication of Cu2O quantum dots (QDs) sensitized p-CuSCN photoelectrode provides a significant photocurrent enhancement in photoelectrochemical medium for the first time. The variation of photocurrent quantum efficiency (Ф%) with Cu2O amount formed on p-CuSCN was presented. Here, two maxima of photocurrent could be observed in Cu/p-CuSCN/Cu2O photoelectrodes. The first photocurrent peak was due to the Cu2O QDs sensitization on p-CuSCN layer, and the second photocurrent peak was due to the formation of p-n junction. Time development of the photocurrent for Cu/p-CuSCN/n-Cu2O photoelectrodes and material characterization from Fourier Transform Infrared (FTIR) spectra, Scanning Electron Microscope (SEM) images, Energy Dispersive X-ray Spectroscopy (EDX) and X-ray diffraction (XRD) were done in this study in detailed.
- 14 November 2017
- Published by IOP Publishing in Materials Research Express
- Vol. 5 (1) , 015005
Explanation of the photocurrent generation of Cu2O quantum dots (QDs) sensitized p-CuSCN stable photoelectrochemical cells
Fabrication of Cu2O quantum dots (QDs) sensitized p-CuSCN photoelectrode provides a significant photocurrent enhancement in photoelectrochemical medium for the first time. The variation of photocurrent quantum efficiency (Ф%) with Cu2O amount formed on p-CuSCN was presented. Here, two maxima of photocurrent could be observed in Cu/p-CuSCN/Cu2O photoelectrodes. The first photocurrent peak was due to the Cu2O QDs sensitization on p-CuSCN layer, and the second photocurrent peak was due to the formation of p-n junction. Time development of the photocurrent for Cu/p-CuSCN/n-Cu2O photoelectrodes and material characterization from Fourier Transform Infrared (FTIR) spectra, Scanning Electron Microscope (SEM) images, Energy Dispersive X-ray Spectroscopy (EDX) and X-ray diffraction (XRD) were done in this study in detailed.
- 1 August 2017
- Published by IOP Publishing in Materials Research Express
- Vol. 4 (8) , 086413
Synthesis of p-Cu2O/rGO composite films for enhancing photocurrent of p-Cu2O and H2generation
Composites of p type cuprous oxide (p-Cu2O) and reduced graphene oxide (rGO) were prepared by depositing an rGO layer on top of nano-sized Cu2O particles prepared on a Cu substrate. These synthesized composites help to enhance the photocurrent over that of bare Cu2O, which means rGO acts as an excellent electron acceptor to separate electrons from Cu2O particles. Here the p-Cu2O layer was fabricated using thermal oxidation and the rGO layer was fabricated using electrophoretic deposition (EPD). The samples thus fabricated were characterized using diffuse reflectance spectra, Fourier transmission infrared (FTIR) spectra, scanning electron microscopy (SEM) images, time development of the photocurrent of photoelectrochemical cells, and electrochemical impedance spectroscopy (EIS) measurements. H2 evolution was observed using a gas chromatograph system.
- 1 August 2017
- Published by IOP Publishing in Materials Research Express
- Vol. 4 (8) , 086413
Synthesis of p-Cu2O/rGO composite films for enhancing photocurrent of p-Cu2O and H2generation
Composites of p type cuprous oxide (p-Cu2O) and reduced graphene oxide (rGO) were prepared by depositing an rGO layer on top of nano-sized Cu2O particles prepared on a Cu substrate. These synthesized composites help to enhance the photocurrent over that of bare Cu2O, which means rGO acts as an excellent electron acceptor to separate electrons from Cu2O particles. Here the p-Cu2O layer was fabricated using thermal oxidation and the rGO layer was fabricated using electrophoretic deposition (EPD). The samples thus fabricated were characterized using diffuse reflectance spectra, Fourier transmission infrared (FTIR) spectra, scanning electron microscopy (SEM) images, time development of the photocurrent of photoelectrochemical cells, and electrochemical impedance spectroscopy (EIS) measurements. H2 evolution was observed using a gas chromatograph system.
- 2 May 2017
- Published by IOP Publishing in Materials Research Express
- Vol. 4 (6) , 065011
Large photocurrent enhancement in the Cu/n-Cu2O/p-Ag2O/n-Cu2O photoelectrode at the electrolyte interface
N type Cuprous Oxide (n-Cu2O) has been shown to be an excellent material for fabricating low cost solar cells due to the optical band gap of ~2.0 eV. A substantial photocurrent enhancement of 80% was measured at the Cu/n-Cu2O-electrolyte interface in a photo-electrochemical cell with the introduction of a thin layer of p type Ag2O between n-Cu2O layers. The enhancement in photocurrent is attributed to the creation of copious electron-hole pairs due to the introduction of a sub-monolayer narrow band gap (~1.5 eV) Ag2O. To study the structure-property and evidence for the presence of fabricated materials, characterization techniques like diffuse reflectance, XRD, EDX, FTIR and SEM have been used.
- 2 May 2017
- Published by IOP Publishing in Materials Research Express
- Vol. 4 (6) , 065011
Large photocurrent enhancement in the Cu/n-Cu2O/p-Ag2O/n-Cu2O photoelectrode at the electrolyte interface
N type Cuprous Oxide (n-Cu2O) has been shown to be an excellent material for fabricating low cost solar cells due to the optical band gap of ~2.0 eV. A substantial photocurrent enhancement of 80% was measured at the Cu/n-Cu2O-electrolyte interface in a photo-electrochemical cell with the introduction of a thin layer of p type Ag2O between n-Cu2O layers. The enhancement in photocurrent is attributed to the creation of copious electron-hole pairs due to the introduction of a sub-monolayer narrow band gap (~1.5 eV) Ag2O. To study the structure-property and evidence for the presence of fabricated materials, characterization techniques like diffuse reflectance, XRD, EDX, FTIR and SEM have been used.