Aldin Justin Sundararaj
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Aldin Justin Sundararaj has a total of 29 co-authors. Here are the top co-authors by number of shared publications:
B. C. Pillai
Propulsion and High Enthalpy laboratory, Aerospace Department, Karunya University 1 , Coimbatore - 641 114, India
2 shared publications- Kesavan Marimuthu
Karunya Institute of Technology and Sciences
2 shared publications A N Subash
1 shared publicationA. N. Subash
Propulsion and High Enthalpy laboratory, Aerospace Department, Karunya University 1 , Coimbatore - 641 114, India
1 shared publicationA. P. Haran
Aeronautical Department, Park College of Engineering and Technology 2 , Coimbatore - 641 659, India
1 shared publication- Abhijith Girish Nair1 shared publication
Latest Publications
- 9 September 2026
- Published by SAGE Publications in International Journal of Protective Structures
Experimental study of blast wave attenuation using perforated plates and sandwich structures
Blast waves in confined environments generate severe overpressures due to repeated wave reflections, posing significant threats to structures and personnel. Therefore, effective mitigation strategies require experimental evaluation under controlled conditions. In the present study, blast wave attenuation using perforated plates, and hybrid sandwich configurations is investigated experimentally using a shock tube facility. Shock waves with velocities between 500 and 650 m/s were generated using driver pressure ranging from 3 to 12 bar and characterized using high-frequency pressure transducers. Circular and triangular plates with perforation ratios (PR) of 30-50% were examined to assess the influence of perforation geometry and blockage ratio on pressure and velocity attenuation. Results show that blast attenuation increases with blockage ratio and is strongly dependent on perforation shape. Circular perforated plates achieved maximum pressure reduction of approximately 59% at 30% perforation ratio, while triangular perforations resulted in a maximum attenuation of 70% at a perforation ratio of 40%. Among the materials tested, polyurethane foam exhibited the highest attenuation, achieving pressure reductions up to 62% due to its superior energy absorption. Hybrid sandwich configurations combining perforated plates with polyurethane foam further improved blast mitigation, achieving pressure reductions up to 70% along with substantial reductions in transmitted shock velocity.
- 9 September 2026
- Published by SAGE Publications in International Journal of Protective Structures
Experimental study of blast wave attenuation using perforated plates and sandwich structures
Blast waves in confined environments generate severe overpressures due to repeated wave reflections, posing significant threats to structures and personnel. Therefore, effective mitigation strategies require experimental evaluation under controlled conditions. In the present study, blast wave attenuation using perforated plates, and hybrid sandwich configurations is investigated experimentally using a shock tube facility. Shock waves with velocities between 500 and 650 m/s were generated using driver pressure ranging from 3 to 12 bar and characterized using high-frequency pressure transducers. Circular and triangular plates with perforation ratios (PR) of 30-50% were examined to assess the influence of perforation geometry and blockage ratio on pressure and velocity attenuation. Results show that blast attenuation increases with blockage ratio and is strongly dependent on perforation shape. Circular perforated plates achieved maximum pressure reduction of approximately 59% at 30% perforation ratio, while triangular perforations resulted in a maximum attenuation of 70% at a perforation ratio of 40%. Among the materials tested, polyurethane foam exhibited the highest attenuation, achieving pressure reductions up to 62% due to its superior energy absorption. Hybrid sandwich configurations combining perforated plates with polyurethane foam further improved blast mitigation, achieving pressure reductions up to 70% along with substantial reductions in transmitted shock velocity.
- Open Access
- 13 February 2026
- Published by Polish Scientific Society of Combustion Engines in Combustion Engines
- Vol. 206 (3) , 140-150
Experimental and kinetic analysis of low to intermediate temperature auto-ignition of binary ethylene-acetylene blends
Understanding the ignition characteristics of binary hydrocarbon blends is essential for designing high-speed propulsion systems such as scramjets, where ignition under short residence time is a critical challenge. In this work, the ignition delay behaviour of ethylene-acetylene/air mixtures was examined through shock tube experiments and kinetic simulations under engine-relevant conditions. Ethylene was used as the primary fuel and blended with acetylene at 5%, 10%, and 20% by volume to form binary mixtures, at an equivalence ratio of 1.0, temperatures between 560–1030 K, and pressures of 2.5–9 bar. The ignition delay time was determined from peak pressure rise and CH* chemiluminescence behind the reflected shock. Unlike previous blended fuel studies dominated by saturated hydrocarbons, this work presents a comprehensive dataset for ethylene-acetylene blends at low to intermediate temperatures and increasing the acetylene fraction from 5% to 20% reduces the ignition delay time by up to 50–60% in the 700–850 K and 2–5 bar regime. Numerical simulations were performed using ANSYS Chemkin in a closed, homogeneous, constant-volume reactor with the NUIG, ARAMCO, LLNL, and San Diego mechanisms. The sensitivity and rate-of-production analyses reveal that ignition is governed by HO2–H2O2 radical chemistry, with the thermal decomposition of H2O2 triggering rapid OH formation. Acetylene enhances ignition by promoting the regeneration of HCCO radicals and accelerating the transition to chain-branching chemistry.
- 13 February 2026
- Published by Polish Scientific Society of Combustion Engines in Combustion Engines
- Vol. 206 (3) , 140-150
Open AccessExperimental and kinetic analysis of low to intermediate temperature auto-ignition of binary ethylene-acetylene blends
Understanding the ignition characteristics of binary hydrocarbon blends is essential for designing high-speed propulsion systems such as scramjets, where ignition under short residence time is a critical challenge. In this work, the ignition delay behaviour of ethylene-acetylene/air mixtures was examined through shock tube experiments and kinetic simulations under engine-relevant conditions. Ethylene was used as the primary fuel and blended with acetylene at 5%, 10%, and 20% by volume to form binary mixtures, at an equivalence ratio of 1.0, temperatures between 560–1030 K, and pressures of 2.5–9 bar. The ignition delay time was determined from peak pressure rise and CH* chemiluminescence behind the reflected shock. Unlike previous blended fuel studies dominated by saturated hydrocarbons, this work presents a comprehensive dataset for ethylene-acetylene blends at low to intermediate temperatures and increasing the acetylene fraction from 5% to 20% reduces the ignition delay time by up to 50–60% in the 700–850 K and 2–5 bar regime. Numerical simulations were performed using ANSYS Chemkin in a closed, homogeneous, constant-volume reactor with the NUIG, ARAMCO, LLNL, and San Diego mechanisms. The sensitivity and rate-of-production analyses reveal that ignition is governed by HO2–H2O2 radical chemistry, with the thermal decomposition of H2O2 triggering rapid OH formation. Acetylene enhances ignition by promoting the regeneration of HCCO radicals and accelerating the transition to chain-branching chemistry.
- Open Access
- 1 August 2023
- Published by Springer Nature in Research Square
Blast Wave Mitigation Through Confined Volume and Porous Material
Over a period of time, the impact of shock waves on human bodies and structures has been studied. To understand the shock wave mitigation over confined volume and porous material, an experimental study is carried out using a shock tube. For the current study, shock velocities ranging from 500 m/s to 650 m/s are created in the tube. The normal shock pressure ranged from 1.1 to 2.8 bar, and the reflected shock pressure ranged from 4.3 to 8 bar in the closed tube. High-frequency PCB pressure transducers is used to measure shock pressure. Three different methods are studied to understand the shock wave mitigation through a confined volume. The methods are perforated bodies with 30%, 40%, and 50% of circular cross section on one side and closed at other end, porous compressible materials kept outside the shock tube to understand head on collision of shock wave and head on shock wave impact on porous material sandwich between the two plates. The number of times the shockwave travelled is highest in the least porous material. On direct shock impact porous compressible material such as glass wool foam, rubber foam is observed to be shredded off, whereas polyurethane foam was comparatively stable. When sandwiching between the two thin plates, it is observed that the shock loading is more on the glass wool foam, less on the rubber foam and the least on the polyurethane foam. It can be concluded that shock waves can be attenuated by perforating bodies, and further impact of the shock can be reduced by materials having blast mitigation properties.
- 1 August 2023
- Published by Springer Nature in Research Square
Open AccessBlast Wave Mitigation Through Confined Volume and Porous Material
Over a period of time, the impact of shock waves on human bodies and structures has been studied. To understand the shock wave mitigation over confined volume and porous material, an experimental study is carried out using a shock tube. For the current study, shock velocities ranging from 500 m/s to 650 m/s are created in the tube. The normal shock pressure ranged from 1.1 to 2.8 bar, and the reflected shock pressure ranged from 4.3 to 8 bar in the closed tube. High-frequency PCB pressure transducers is used to measure shock pressure. Three different methods are studied to understand the shock wave mitigation through a confined volume. The methods are perforated bodies with 30%, 40%, and 50% of circular cross section on one side and closed at other end, porous compressible materials kept outside the shock tube to understand head on collision of shock wave and head on shock wave impact on porous material sandwich between the two plates. The number of times the shockwave travelled is highest in the least porous material. On direct shock impact porous compressible material such as glass wool foam, rubber foam is observed to be shredded off, whereas polyurethane foam was comparatively stable. When sandwiching between the two thin plates, it is observed that the shock loading is more on the glass wool foam, less on the rubber foam and the least on the polyurethane foam. It can be concluded that shock waves can be attenuated by perforating bodies, and further impact of the shock can be reduced by materials having blast mitigation properties.
- 21 January 2021
- Published by SAGE Publications in International Journal of Engine Research
- Vol. 23 (3) , 460-468
Experimental investigation of the effect of temperature on ignition of modified kerosene
Kerosene based hydrocarbon fuels are preferred candidates for the source of energy due to its stable properties. Based on the requirement of the combustor and the growing concern over pollutant, kerosene based fuels are modified. The fuel under investigation is a modified form of kerosene with ultra-low sulphur content. The effect of temperature on modified kerosene is studied for viscosity, surface tension, specific heat, density and ignition delay. The time delay for ignition of gas-phase mixtures of modified kerosene/oxygen have been measured using a shock tube facility. The experiments are conducted in the temperature range of 1200–1877 K, pressure range of 4–12 atm and equivalence ratio of Ø = 1.5, 1 and 0.5. The ignition delay time measurements were carried out using piezoelectric pressure transducers, which records the pressure rise due to ignition and simultaneously recording the light emission during the process of ignition using a photodiode. The ignition delay is represented as τign = 0.168841 × P−1.49 × Ø0.72 × e(14310/T)
- 21 January 2021
- Published by SAGE Publications in International Journal of Engine Research
- Vol. 23 (3) , 460-468
Experimental investigation of the effect of temperature on ignition of modified kerosene
Kerosene based hydrocarbon fuels are preferred candidates for the source of energy due to its stable properties. Based on the requirement of the combustor and the growing concern over pollutant, kerosene based fuels are modified. The fuel under investigation is a modified form of kerosene with ultra-low sulphur content. The effect of temperature on modified kerosene is studied for viscosity, surface tension, specific heat, density and ignition delay. The time delay for ignition of gas-phase mixtures of modified kerosene/oxygen have been measured using a shock tube facility. The experiments are conducted in the temperature range of 1200–1877 K, pressure range of 4–12 atm and equivalence ratio of Ø = 1.5, 1 and 0.5. The ignition delay time measurements were carried out using piezoelectric pressure transducers, which records the pressure rise due to ignition and simultaneously recording the light emission during the process of ignition using a photodiode. The ignition delay is represented as τign = 0.168841 × P−1.49 × Ø0.72 × e(14310/T)
- 1 January 2021
- Published by American Scientific Publishing Group (ASPG) LLC
- Vol. 5 (1) , 17-27
Guardians of the IoT Galaxy: Using Deep Learning to Secure IoT Networks Against Botnet Attacks
American scientific publishing group
- 1 January 2021
- Published by American Scientific Publishing Group (ASPG) LLC
- Vol. 5 (1) , 17-27
Guardians of the IoT Galaxy: Using Deep Learning to Secure IoT Networks Against Botnet Attacks
American scientific publishing group
- 1 February 2019
- Published by Geological Society of India in Journal of the Geological Society of India
- Vol. 93 (2) , 218-222
Investigation of Ignition Delay for Low Molecular Weight Hydrocarbon Fuel by Using Shock Tube in Reflected Shock Mode
Shock tube facility in the Propulsion and High Enthalpy laboratory, Aerospace Engineering Department, has been extensively used to study the ignition characteristics of fuels by measuring the ignition delay times for various hydrocarbon fuels at high temperatures. Initially a systematic method has been followed to calibrate the shock tube for ignition delay time measurements by measuring the delay times of C2H6 – O2 gas mixture diluted with argon. The results show good agreement with earlier reported works of Ethane ignition. Ignition times of low molecular weight liquefied petroleum gas, a fuel used in many industrial and household applications has been studied in the temperature range of 1250-1880 K and in the pressure range of 6-11 atm at equivalence ratios (Φ = 0.5 & 1). The ignition delay was measured in the reflected shock region by recording the ignition-induced pressure rise and emission from CH radical simultaneously. From the present study it is noted that the ignition delay time for liquefied petroleum gas reduces with increase in temperature and its activation energy lies in the range of 40 kcal/mol.
- 1 February 2019
- Published by Geological Society of India in Journal of the Geological Society of India
- Vol. 93 (2) , 218-222
Investigation of Ignition Delay for Low Molecular Weight Hydrocarbon Fuel by Using Shock Tube in Reflected Shock Mode
Shock tube facility in the Propulsion and High Enthalpy laboratory, Aerospace Engineering Department, has been extensively used to study the ignition characteristics of fuels by measuring the ignition delay times for various hydrocarbon fuels at high temperatures. Initially a systematic method has been followed to calibrate the shock tube for ignition delay time measurements by measuring the delay times of C2H6 – O2 gas mixture diluted with argon. The results show good agreement with earlier reported works of Ethane ignition. Ignition times of low molecular weight liquefied petroleum gas, a fuel used in many industrial and household applications has been studied in the temperature range of 1250-1880 K and in the pressure range of 6-11 atm at equivalence ratios (Φ = 0.5 & 1). The ignition delay was measured in the reflected shock region by recording the ignition-induced pressure rise and emission from CH radical simultaneously. From the present study it is noted that the ignition delay time for liquefied petroleum gas reduces with increase in temperature and its activation energy lies in the range of 40 kcal/mol.
- 18 April 2018
- Published by Springer Nature in Journal of Mechanical Science and Technology
- Vol. 32 (4) , 1685-1691
Convective heat transfer analysis of refined kerosene with alumina particles for rocketry application
- 18 April 2018
- Published by Springer Nature in Journal of Mechanical Science and Technology
- Vol. 32 (4) , 1685-1691
Convective heat transfer analysis of refined kerosene with alumina particles for rocketry application
- 28 December 2017
- Published by Springer Nature
- p. 309-322
Development of Single and Multi-jet Conical Nozzle Based Open Jet Facility for Cold Jet Simulation
- 28 December 2017
- Published by Springer Nature
- p. 309-322
Development of Single and Multi-jet Conical Nozzle Based Open Jet Facility for Cold Jet Simulation