Apang Djafar Shieddieque
Apang Djafar Shieddieque has a total of 26 co-authors. Here are the top co-authors by number of shared publications:
Bambang Widyanto
Universitas Jendral Ahmad Yani, Indonesia
4 shared publicationsRochim Suratman
Inst Teknol Bandung, Fac Mech & Aerosp Engn, Ganesha 10, Bandung 40132, Indonesia
3 shared publications- Sukarman Sukarman
Universitas Buana Perjuangan Karawang, Indonesia
3 shared publications - Amri Abdulah
Department of Mechanical Engineering, Faculty of Engineering, Universitas Sebelas Maret, Jl. Ir. Sutami 36A Kentingan, Surakarta 57126, Indonesia
2 shared publications - Dede Ardi Rajab
Sekolah Tinggi Teknologi Wastukancana
2 shared publications - Khoirudin Khoirudin
Department of Mechanical Engineering, Faculty of Engineering, Universitas Sebelas Maret, Jl. Ir. Sutami 36A Kentingan, Surakarta 57126, Indonesia
2 shared publications
Latest Publications
- Open Access
- 12 January 2025
- Published by Universitas Muhammadiyah Magelang in Mechanical Engineering for Society and Industry
- Vol. 5 (1) , 133-144
Development of hybrid nanofluids and solar heat exchangers (SHX) to improve heat transfer performance in solar panel cooling
This study examined the thermohydraulic efficiency of a novel Solar Heat Exchanger (SHX) designed for cooling solar panels. The SHX was specifically created for 20 Wp solar panels measuring 450 × 350 mm. The cooling medium was a hybrid nanofluid (HNF) consisting of Alâ‚‚O₃ and SiOâ‚‚ nanoparticles (0.5”“1%) suspended in a base fluid of ethylene glycol and water (EG/W) at a 10:90 ratio. Experiments were performed using flow rates ranging from 1 to 3 LPM. The HNF coolant demonstrated enhanced performance in the solar heat exchanger, with a maximum heat transfer rate increase of 56.07% compared with that of the base fluid. This improvement in the heat-transfer rate was associated with an increase in the heat-transfer coefficient, which was influenced by the flow rate and volume fraction of the HNF. The effectiveness of the HNF surpassed that of the base fluids by approximately 117%. The results indicated that higher flow rates and volume fractions improved cooling performance. The enhanced cooling efficiency and innovative SHX design make this study particularly relevant to the development of solar panel cooling systems, particularly those employing hybrid nanofluid coolants.
- 12 January 2025
- Published by Universitas Muhammadiyah Magelang in Mechanical Engineering for Society and Industry
- Vol. 5 (1) , 133-144
Open AccessDevelopment of hybrid nanofluids and solar heat exchangers (SHX) to improve heat transfer performance in solar panel cooling
This study examined the thermohydraulic efficiency of a novel Solar Heat Exchanger (SHX) designed for cooling solar panels. The SHX was specifically created for 20 Wp solar panels measuring 450 × 350 mm. The cooling medium was a hybrid nanofluid (HNF) consisting of Alâ‚‚O₃ and SiOâ‚‚ nanoparticles (0.5”“1%) suspended in a base fluid of ethylene glycol and water (EG/W) at a 10:90 ratio. Experiments were performed using flow rates ranging from 1 to 3 LPM. The HNF coolant demonstrated enhanced performance in the solar heat exchanger, with a maximum heat transfer rate increase of 56.07% compared with that of the base fluid. This improvement in the heat-transfer rate was associated with an increase in the heat-transfer coefficient, which was influenced by the flow rate and volume fraction of the HNF. The effectiveness of the HNF surpassed that of the base fluids by approximately 117%. The results indicated that higher flow rates and volume fractions improved cooling performance. The enhanced cooling efficiency and innovative SHX design make this study particularly relevant to the development of solar panel cooling systems, particularly those employing hybrid nanofluid coolants.
- Open Access
- 1 January 2024
- Published by International Digital Organization for Scientific Information (IDOSI) in International Journal of Engineering
- Vol. 37 (10) , 1979-1988
Optimization of In-situ Synthesis Process Parameters of LiFePO4/C-MAF-5 Surface Modification for Conductivity Improvement of Lithium-ion Battery Cathode Material by Response Surface Method
This study presents an evaluation of the conductivity of in-situ synthesis of LiFePO4/C-MAF-5 through the use of Response Surface Methodology (RSM) in optimizing process parameters.. Performance and optimization were established by combining RSM with the experimental carbonation process, crystallographic analysis using X-ray diffraction (XRD), and Fourier infrared spectroscopy (FT-IR). The results revealed that crystal structure is important in determining electrical properties, with conductivity consistently higher at smaller sample sizes. Furthermore, the main focus is provided on how the lattice parameters and electrical conductivity of LiFePO4 are affected by particle size. The higher electrical conductivity is due to the smaller particles, where reduced lattice strain is indicated. Furthermore, the success of the synthesis process was confirmed by the absorption peaks that corresponded to the expected LiFePO4 features and corresponded to specific vibrational methods as presented in the FT-IR spectrum results. The complex relationship between conductivity, LiFePO4 amount, and imidazole concentration is demonstrated by the RSM contour plot. It was found that the optimal LFP concentration was 4 mol, the ideal Imidazole concentration was 58.79 mol, and the optimal temperature was set at 700 °C. Under these recommended operating conditions, the resulting conductivity was determined to be 0.0000592 S cm-1.
- 1 January 2024
- Published by International Digital Organization for Scientific Information (IDOSI) in International Journal of Engineering
- Vol. 37 (10) , 1979-1988
Open AccessOptimization of In-situ Synthesis Process Parameters of LiFePO4/C-MAF-5 Surface Modification for Conductivity Improvement of Lithium-ion Battery Cathode Material by Response Surface Method
This study presents an evaluation of the conductivity of in-situ synthesis of LiFePO4/C-MAF-5 through the use of Response Surface Methodology (RSM) in optimizing process parameters.. Performance and optimization were established by combining RSM with the experimental carbonation process, crystallographic analysis using X-ray diffraction (XRD), and Fourier infrared spectroscopy (FT-IR). The results revealed that crystal structure is important in determining electrical properties, with conductivity consistently higher at smaller sample sizes. Furthermore, the main focus is provided on how the lattice parameters and electrical conductivity of LiFePO4 are affected by particle size. The higher electrical conductivity is due to the smaller particles, where reduced lattice strain is indicated. Furthermore, the success of the synthesis process was confirmed by the absorption peaks that corresponded to the expected LiFePO4 features and corresponded to specific vibrational methods as presented in the FT-IR spectrum results. The complex relationship between conductivity, LiFePO4 amount, and imidazole concentration is demonstrated by the RSM contour plot. It was found that the optimal LFP concentration was 4 mol, the ideal Imidazole concentration was 58.79 mol, and the optimal temperature was set at 700 °C. Under these recommended operating conditions, the resulting conductivity was determined to be 0.0000592 S cm-1.
- Open Access
- 7 June 2023
- Published by Jurnal Teknologika, Sekolah Tinggi Teknologi Wastukancana in Jurnal Teknologika
- Vol. 13 (1) , 9-19
PERANCANGAN MOLD SET KOMPONEN HANDLE PINTU MOBIL DENGAN MATERIAL ALUMUNIUM 6061
In the world of the manufacturing industry, developments and needs are increasing every day and very rapidly. Many parts and components in automotive production are very important and very much too because each component has its own function and use. There are many alternatives and development of materials for component manufacturing in the automotive world which aim to cut production costs and efficiency. To overcome this condition, the authors tried to research and make a Mold for the Avansa car door handle using HIPP (High Impact PolyPropilane) material. Generally, not many HIPP use it in the automotive industry. Making this door hendle using the Hot Compression process. Among other things, hot compress is the process of making a product by using heat and pressure to form the desired product. So far, making molding is less precise because mold making is not in accordance with the manufacturing process, therefore the author uses a CNC (Computer numarical control) machine for this molding-making process, the molding process using this CNC machine aims to make the results more precise and more accurate. more as desired.
- 7 June 2023
- Published by Jurnal Teknologika, Sekolah Tinggi Teknologi Wastukancana in Jurnal Teknologika
- Vol. 13 (1) , 9-19
Open AccessPERANCANGAN MOLD SET KOMPONEN HANDLE PINTU MOBIL DENGAN MATERIAL ALUMUNIUM 6061
In the world of the manufacturing industry, developments and needs are increasing every day and very rapidly. Many parts and components in automotive production are very important and very much too because each component has its own function and use. There are many alternatives and development of materials for component manufacturing in the automotive world which aim to cut production costs and efficiency. To overcome this condition, the authors tried to research and make a Mold for the Avansa car door handle using HIPP (High Impact PolyPropilane) material. Generally, not many HIPP use it in the automotive industry. Making this door hendle using the Hot Compression process. Among other things, hot compress is the process of making a product by using heat and pressure to form the desired product. So far, making molding is less precise because mold making is not in accordance with the manufacturing process, therefore the author uses a CNC (Computer numarical control) machine for this molding-making process, the molding process using this CNC machine aims to make the results more precise and more accurate. more as desired.
- Open Access
- 16 December 2022
- Published by Nak-Kanak: Journal of Child Research in Rekayasa
- Vol. 15 (3) , 316-325
Pengaruh Variasi Campuran Bentonit Terhadap Karakteristik Pasir Cetak Untuk Proses Sand Casting
Pengaruh Variasi Campuran Bentonit Terhadap Karakteristik Pasir Cetak Untuk Proses Sand Casting
- 16 December 2022
- Published by Nak-Kanak: Journal of Child Research in Rekayasa
- Vol. 15 (3) , 316-325
Open AccessPengaruh Variasi Campuran Bentonit Terhadap Karakteristik Pasir Cetak Untuk Proses Sand Casting
Pengaruh Variasi Campuran Bentonit Terhadap Karakteristik Pasir Cetak Untuk Proses Sand Casting
- Open Access
- 23 April 2022
- Published by Universitas Muhammadiyah Magelang in Automotive Experiences
- Vol. 5 (3) , 288-303
Multi-objective Optimization of Sansevieria Trifasciata Fiber Reinforced Vinyl Ester (STF/VE) Bio-composites for the Sustainable Automotive Industry
Bio-composite materials have taken an extensive interest in research over the years due to their excellent properties, such as excellent mechanical and physical properties, stiffness, and low density/lightweight. The exceptional properties of bio-composite materials have had a widespread application in several industries, such as; the packaging industry, construction, automotive, and other related engineering fields. This research investigates mechanical, physical, and microstructure properties of Sansevieria Trifasciata (STE) natural fiber, -reinforced Vinyl Ester (STF/VE) bio-composite. The mechanical and physical properties of STF/VE bio-composites, including the tensile strength and density, are investigated through fibre preparation, orientation, and fibre volume fraction parameters. The STF/VE bio-composite tensile strength coupon is manufactured using the bio-composite transfer moulding (BTM) process and with pressure moulding. The Taguchi experimental design and analysis of variance (ANOVA) are selected to investigate the effect of variables on the mechanical properties model. The alkali preparation of STF, unidirectional fibre orientation, and fibre volume fraction improve tensile strength. Non-alkali treatment and random fibre orientatio, on the other hand, result in a reduction of density. The results of the ANOVA analysis show that the fibre volume fraction (wt.%) is the variable that most significantly affects the tensile strength and density responses, with contributions of 50.57% of tensile strength and 51.34% of density, respectively. Based on the optimization results, the STF/VE with alkali treatment, unidirectional, and 15 w.t.% is chosen as the best bio-composite formulation, with the best tensile strength-density balance. It indicates that the optimum parameter was successfully achieved among the samples examined in this work.
- 23 April 2022
- Published by Universitas Muhammadiyah Magelang in Automotive Experiences
- Vol. 5 (3) , 288-303
Open AccessMulti-objective Optimization of Sansevieria Trifasciata Fiber Reinforced Vinyl Ester (STF/VE) Bio-composites for the Sustainable Automotive Industry
Bio-composite materials have taken an extensive interest in research over the years due to their excellent properties, such as excellent mechanical and physical properties, stiffness, and low density/lightweight. The exceptional properties of bio-composite materials have had a widespread application in several industries, such as; the packaging industry, construction, automotive, and other related engineering fields. This research investigates mechanical, physical, and microstructure properties of Sansevieria Trifasciata (STE) natural fiber, -reinforced Vinyl Ester (STF/VE) bio-composite. The mechanical and physical properties of STF/VE bio-composites, including the tensile strength and density, are investigated through fibre preparation, orientation, and fibre volume fraction parameters. The STF/VE bio-composite tensile strength coupon is manufactured using the bio-composite transfer moulding (BTM) process and with pressure moulding. The Taguchi experimental design and analysis of variance (ANOVA) are selected to investigate the effect of variables on the mechanical properties model. The alkali preparation of STF, unidirectional fibre orientation, and fibre volume fraction improve tensile strength. Non-alkali treatment and random fibre orientatio, on the other hand, result in a reduction of density. The results of the ANOVA analysis show that the fibre volume fraction (wt.%) is the variable that most significantly affects the tensile strength and density responses, with contributions of 50.57% of tensile strength and 51.34% of density, respectively. Based on the optimization results, the STF/VE with alkali treatment, unidirectional, and 15 w.t.% is chosen as the best bio-composite formulation, with the best tensile strength-density balance. It indicates that the optimum parameter was successfully achieved among the samples examined in this work.
- Open Access
- 3 August 2021
- Published by Nak-Kanak: Journal of Child Research in Rekayasa
- Vol. 14 (2) , 238-244
Analisis Material Efoxy EF150K Terhadap Temperatur dan Kelembaman Tinggi Pada Komponen Charger Mobil Listrik
Electric cars have now been made and developed by famous car manufacturers outside of Indonesia. Of course electric cars have batteries that must be recharge. Inside the electric car charger there is a controller which is one of the components, which is an epoxy coated capacitor. The faster the charger, the higher the temperature will be, to deal with this problem, it is necessary to increase the performance of the capacitor to increase the temperature and humidity resistance. Then from this explanation the researchers will test the EF150K epoxy coating on the Disc Ceramic Capacitor (DCC), by using epoxy coating thickness testing by using 3 samples the results obtained are on average 0.8 mm, Pressure Cycle Test (PCT) using 20 samples with conditions temp: 121 °C, p: 2 bar for 48 hour, obtained average capacities and insulance resistance before PCT testing C: 2155,4pF, IR: 141540Ω and after C: 2238,2 pF, IR: 147140 Ω, and humidity test using 20 sample with condition 95% RH, temp: 40°C for 504h obtained average capacities and insulance resistance before humidity test C: 2.157,89 pF, IR: 119560 Ω and after C: 2.233,63 pF, IR: 123160 Ω. The use of EF150K epoxy is very well used as a DCC capacitor coating, because the coating is resistant to temperatures up to 121 ° C with a pressure of 2 bar, and withstands temperatures up to 40 °C with 95% RH.
- 3 August 2021
- Published by Nak-Kanak: Journal of Child Research in Rekayasa
- Vol. 14 (2) , 238-244
Open AccessAnalisis Material Efoxy EF150K Terhadap Temperatur dan Kelembaman Tinggi Pada Komponen Charger Mobil Listrik
Electric cars have now been made and developed by famous car manufacturers outside of Indonesia. Of course electric cars have batteries that must be recharge. Inside the electric car charger there is a controller which is one of the components, which is an epoxy coated capacitor. The faster the charger, the higher the temperature will be, to deal with this problem, it is necessary to increase the performance of the capacitor to increase the temperature and humidity resistance. Then from this explanation the researchers will test the EF150K epoxy coating on the Disc Ceramic Capacitor (DCC), by using epoxy coating thickness testing by using 3 samples the results obtained are on average 0.8 mm, Pressure Cycle Test (PCT) using 20 samples with conditions temp: 121 °C, p: 2 bar for 48 hour, obtained average capacities and insulance resistance before PCT testing C: 2155,4pF, IR: 141540Ω and after C: 2238,2 pF, IR: 147140 Ω, and humidity test using 20 sample with condition 95% RH, temp: 40°C for 504h obtained average capacities and insulance resistance before humidity test C: 2.157,89 pF, IR: 119560 Ω and after C: 2.233,63 pF, IR: 123160 Ω. The use of EF150K epoxy is very well used as a DCC capacitor coating, because the coating is resistant to temperatures up to 121 ° C with a pressure of 2 bar, and withstands temperatures up to 40 °C with 95% RH.
- 19 July 2021
- Published by International Journal of Technology in International Journal of Technology
- Vol. 12 (3) , 549-560
Preparation and Characterization of Sansevieria trifasciata Fiber/High-Impact Polypropylene and Sansevieria trifasciata Fiber/Vinyl Ester Biocomposites for Automotive Applications
The increasing demand for vehicles is resulting in environmental problems, such as a higher demand for fossil fuels and higher CO2 emissions. Lightweight materials, such as fiber-reinforced polymers, have been used in automotive components to reduce the weight, fuel consumption, and CO2 emissions of vehicles. Natural fibers are often used as substitutes for glass fibers because they are abundant and require less energy to produce compared to glass fibers. The present research focused on the preparation and characterization of composites reinforced with Sansevieria trifasciata fiber (STF). High-impact polypropylene (HIPP) and vinyl ester (VE) were chosen and compared as matrix materials. The results showed that the mechanical properties of the produced biocomposites increased with increasing amounts of fiber, alkaline treatment, and unidirectional fiber orientation. A tensile strength of 59.77 MPa and a stiffness of 1.97 GPa were obtained for STF/HIPP composites with unidirectional alkali treatment and a 15% volume fraction of fiber. Moreover, a tensile strength of 121.1 MPa and a stiffness of 7.65 GPa were obtained for STF/VE composites with unidirectional alkali treatment and a 15% volume fraction of fiber. The STF/VE biocomposites were comparable to commercial glass fiber composites for automotive applications and even exhibited greater tensile strength properties.
- 19 July 2021
- Published by International Journal of Technology in International Journal of Technology
- Vol. 12 (3) , 549-560
Preparation and Characterization of Sansevieria trifasciata Fiber/High-Impact Polypropylene and Sansevieria trifasciata Fiber/Vinyl Ester Biocomposites for Automotive Applications
The increasing demand for vehicles is resulting in environmental problems, such as a higher demand for fossil fuels and higher CO2 emissions. Lightweight materials, such as fiber-reinforced polymers, have been used in automotive components to reduce the weight, fuel consumption, and CO2 emissions of vehicles. Natural fibers are often used as substitutes for glass fibers because they are abundant and require less energy to produce compared to glass fibers. The present research focused on the preparation and characterization of composites reinforced with Sansevieria trifasciata fiber (STF). High-impact polypropylene (HIPP) and vinyl ester (VE) were chosen and compared as matrix materials. The results showed that the mechanical properties of the produced biocomposites increased with increasing amounts of fiber, alkaline treatment, and unidirectional fiber orientation. A tensile strength of 59.77 MPa and a stiffness of 1.97 GPa were obtained for STF/HIPP composites with unidirectional alkali treatment and a 15% volume fraction of fiber. Moreover, a tensile strength of 121.1 MPa and a stiffness of 7.65 GPa were obtained for STF/VE composites with unidirectional alkali treatment and a 15% volume fraction of fiber. The STF/VE biocomposites were comparable to commercial glass fiber composites for automotive applications and even exhibited greater tensile strength properties.
- Open Access
- 1 August 2019
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 547 (1) , 012048
The Effect of Dibutyl phthalate plasticizer to Impregnation and Mechanical Properties of Biocomposite Sansevieria trifasciata/High Impact Polypropylene
The aim of this research was to investigate the effect of dibutyl phthalate plasticizer to impregnation and mechanical properties of biocomposite sansevieria trifasciata/high impact polypropylene and to analyze the morphology of interfacial bond between matrix and fiber. In this research, biocomposite sansevieria trifasciata/high impact polypropylene was manufactured by using a hot press method with temperature 180°C and pressure 140 bar for 10 minutes. Fibers were extracted from sansevieria trifasciata by using mechanical retting. In this experiment, the fibers weree treated by NaOH 3% (wt%) solution at temperature 100°C for an hour. The volume fractions of fiber used in this experiment were 0%, 15%, 25%, and 35% with unidirectional orientation. To improve impregnation of high impact polypropylene matrix, 2% dibutyl phthalate was added as plasticizer. Actual density and mechanical properties of biocompositesare conducted based on ASTM standard testing methods D792 and D3039. The results showed that tensile strength, modulus of elasticity and elongations of bio composite sansevieria trifasciata/high impact polypropylene with plasticizer were higher than without added plasticizer. The fracture analysis was investigated by scanning electron microscope (SEM). The highest tensile strength, modulus of elasticity and elongation of biocomposites were 65 Mpa, 2.31 GPa and 0.42% respectively. Their highest properties were obtained from bio composites with 35 % volume fraction of unidirectional alkaline treated fiberand 2% dibutyl phthalate. Morphological feature based on scanning electron microscope (SEM) observation showed that biocomposites with added plasticizer had better interface bond between matrix and fibers.
- 1 August 2019
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 547 (1) , 012048
Open AccessThe Effect of Dibutyl phthalate plasticizer to Impregnation and Mechanical Properties of Biocomposite Sansevieria trifasciata/High Impact Polypropylene
The aim of this research was to investigate the effect of dibutyl phthalate plasticizer to impregnation and mechanical properties of biocomposite sansevieria trifasciata/high impact polypropylene and to analyze the morphology of interfacial bond between matrix and fiber. In this research, biocomposite sansevieria trifasciata/high impact polypropylene was manufactured by using a hot press method with temperature 180°C and pressure 140 bar for 10 minutes. Fibers were extracted from sansevieria trifasciata by using mechanical retting. In this experiment, the fibers weree treated by NaOH 3% (wt%) solution at temperature 100°C for an hour. The volume fractions of fiber used in this experiment were 0%, 15%, 25%, and 35% with unidirectional orientation. To improve impregnation of high impact polypropylene matrix, 2% dibutyl phthalate was added as plasticizer. Actual density and mechanical properties of biocompositesare conducted based on ASTM standard testing methods D792 and D3039. The results showed that tensile strength, modulus of elasticity and elongations of bio composite sansevieria trifasciata/high impact polypropylene with plasticizer were higher than without added plasticizer. The fracture analysis was investigated by scanning electron microscope (SEM). The highest tensile strength, modulus of elasticity and elongation of biocomposites were 65 Mpa, 2.31 GPa and 0.42% respectively. Their highest properties were obtained from bio composites with 35 % volume fraction of unidirectional alkaline treated fiberand 2% dibutyl phthalate. Morphological feature based on scanning electron microscope (SEM) observation showed that biocomposites with added plasticizer had better interface bond between matrix and fibers.